Honda cl90 Swap meet find part 2 #barnfind #tarylfixesall #viral #ct90 @tarylfixesallskits

Рет қаралды 1,508

2 ай бұрын

Today we get into part two of getthe cl90 Running again! but first Buckets Tries to head back in time to see if he could find the proper parts in 1967 and decides to borrow the tardis 😆
As always thanks to #tarylfixesall ! you can check him out
@tarylfixesall
For the doctor who And the eleventh Doctor skit. (Everybody knows i'm a big doctor who fan ) check out the trailer
kzfaq.info/get/bejne/h7Ohh8ugltillYk.htmlsi=MzwaIBZ60LH7l-DF
The next car slot meet profile.php?id=100066741278194&mibextid=kFxxJD
#vicegripgarage

Пікірлер: 24

@AdamDeal-KF0PRI 2 ай бұрын

ITS ALIVE! IT SHALL LIVE! and camera girl mowing grasss! 😂😂😂! by the way thanks for the light show sir!

@leviphillips1589 2 ай бұрын

Nice job, sweet find on the big bore top. I’m actually the guy who sold this to you at Canfield. Been following it since. Glad to see it start up and being used. Would have been all parts if you didn’t get it.

@bucketsgarage 2 ай бұрын

Hey bud, thanks It's quite a bit of work but a lot of fun to see that old thing run again. Still got some more work to do to it but it'll get there in time. Thanks for watching and thanks for the great bike ☺️

@leviphillips1589 2 ай бұрын

@@bucketsgarage the best bikes are the ones you wrench on the most

@kevinhaley6776 2 ай бұрын

My older brother used to have the same bike in the 70s he loved it

@indianachrisUDX1313 2 ай бұрын

Pretty Cool! That larger Jug & Piston should make it fly once you go through that Trans!

@indianachrisUDX1313 2 ай бұрын

OH & Hey to Camera Girl...

@bucketsgarage 2 ай бұрын

O ya I sure love to dig into that right now but you know got to get ready for Portland 😁

@indianachrisUDX1313 2 ай бұрын

@@bucketsgarage Be safe & have a good Time Brother! Happy Memorial Day.

@bucketsgarage 2 ай бұрын

You as well 😊

@Kev-N42000 2 ай бұрын

Just finished watching the video , can’t wait to see what’s making it not shift lol

@bucketsgarage 2 ай бұрын

Yeah I'm going to start off. Simple on that one. Hopefully it's a tumblers on the clutch side. Hopefully I don't have to split the whole engine that would stink 🙄

@Kev-N42000 2 ай бұрын

Big Bore! I like it, never seen a piston like that in one them before lol

@bucketsgarage 2 ай бұрын

I know right when I took it apart. I'm like holy buckets. What have I got here? It's awesome. Never knew if it was even in that engine 😆

@iancameron198 2 ай бұрын

Where did you get the book.i can use one for my ST90 HONDA 1974@@bucketsgarage

@bucketsgarage 2 ай бұрын

@@iancameron198 I've had that for many years. I actually I think I found it at a swap meet. Let me do some research for you. Let's see if I can locate one. I'll get back to you as soon as I can

@bucketsgarage 2 ай бұрын

Okay bud, you can find a few that's books on eBay. This one here looked pretty good for what you want to do. Here's the link to it what I'll do is I'll take a picture of the one I do have and post it on my Facebook page. Bunker's garage hope this helps you out man. Let me know. Have a great night and thanks for watching. www.ebay.com/itm/364794678609?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=RV5cOengQ5q&sssrc=4429486&ssuid=t1-uOIcURNm&var=&widget_ver=artemis&media=COPY

@Kev-N42000 2 ай бұрын

I would of put the wrist pin circlip with the space directly up or down , when installed with the circlip gap sideways there’s always a chance under reciprocal forces that the circlip can compress flex and pop out , im sure it don’t matter on that low rev Honda but I always go ahead and install with the gap up or down anyways

@bucketsgarage 2 ай бұрын

That is definitely good advice. Thanks bud!

@donsoule6411 Ай бұрын

@@bucketsgarageAnother suggestion, or better yet a recommendation… When removing or installing wrist pin cir-clips, stuff a rag or something else into or over the crankcase opening to prevent the potential “launch” of the clip into the engine!