Honda GCV160 Carburetor Replacement, Troy-Built TB130

Рет қаралды 10,295

Күн бұрын

How to replace the carburetor on a Honda GCV160. Remove and install. I used the Amazon carb at the link below and it runs great!
Carb Used: amzn.to/3ZrzB1t
Dewalt Impact Driver Used: amzn.to/3rl2AY6
Impact Socket Set: amzn.to/3PLwiid
Mower Mike’s Tool Store: www.amazon.com/shop/mowermike
Mower Mike
Disclosure: The Amazon link above is an Amazon affiliate links. This means that, I do earn a very small commission (at no cost to you) if you click the link and finalize a purchase.

Пікірлер: 36

@user-ih7jx8is9g Ай бұрын

Thank you, thank you! I took out the long screws, it all dropped down and could not figure how it went back together! You are a lifesaver!!

@MowerMike Ай бұрын

Haha I wouldn’t go that far but you are welcome. Now get to mowin!

@charlesbroomfield9832 Ай бұрын

same here!!

@hcslade3068 17 күн бұрын

That’s why I’m here!

@Amarillobymorning777 29 күн бұрын

Well : I followed your advice. Got the same part number. Put new carburetor with gaskets I used little tip of regular grease to hold the gaskets on the choke. Replace the spark plug And air filter. Start right up . Sounds and feels with more power on it . Blessing and greetings Señor from North Texas. Psalm 23 . Muchas gracias 🙏 21 bucks for the kit .

@MowerMike 28 күн бұрын

Glad you got her going. Great verse had to google Psalms 23. FYI my wife is from Amarillo and she hates that song lol.

@Amarillobymorning777 28 күн бұрын

@@MowerMike With all my respects play Lady From Kenny Rogers. Try to make it up . .

@MowerMike 28 күн бұрын

@@Amarillobymorning777 Haha yes sir now that is a winner, little slow but will take it.

@MowerMike 26 күн бұрын

@@Amarillobymorning777 I did and she actually likes that song, was shocked.

@Amarillobymorning777 26 күн бұрын

@@MowerMike Jajajajaja cheers buddy.

@entrthedragon Ай бұрын

As you take a bolt out replace it with a headless bolt to keep everything in place (from another vid).

@MowerMike Ай бұрын

Headless bolt???? Doesn’t sound like much of a bolt

@entrthedragon Ай бұрын

@@MowerMike it’s just temporary to hold stuff in place then when you replace, you put your regular bolts back on. Some people use 3/16” wood dowels to keep stuff in place too. Just work arounds to make it less of a PITA.

@ingramcl Ай бұрын

most use 6M 100MM rods with or w/o thread help hold things in place until your ready to install. At least that's what I found on another video & I will attempt 2 change my own carburetor 2moro. Thnx 4 your video too bcuz they all help. 😁

@entrthedragon Ай бұрын

@@ingramcl For sure, whatever works to keep it all in place. Good luck!

@cgilleybsw 18 күн бұрын

that's a brilliant hack!

@albondigas9549 29 күн бұрын

the gasket is so you can hold on to it during assy. 😮

@cgilleybsw 18 күн бұрын

You know, there are some things I just don't expect from Honda - a carburetor that falls apart is one of them. That said, a touch of gasket goop or grease would do the same as super glue. The only other thing I have seen worse from Honda is on some of their older Civics. The oil filter is between the firewall and the back of the engine and directly over the exhaust manifold. So, off to find some gasket goop.

@MowerMike 18 күн бұрын

Gasket goop? Be careful gas eats most goops. Needs to be a carb specific gasket. Never worked on a Honda car am a Chevy or MiniCooper type of guy

@obiemains1367 2 ай бұрын

a7 6;49, that gasket is on backwards. small hole goes on other side

@MowerMike 2 ай бұрын

Good eye, backwards or not it worked great

@Harry67544 Ай бұрын

My seems to rev way too high. Any tips?

@MowerMike Ай бұрын

It probably has an air leak. Try spraying carb cleaner around the intake and see if it changes. When it is reving too high it is sucking in air from somewhere. May just need to tighten down the carb bolts. Good luck

@Harry67544 Ай бұрын

@@MowerMike Thanks man! I found out it was my general allowing too much throttle. Gave me a little scare!