Excellent demonstration on how to properly adjust and use this tool. I have used this tool but now I think you fully taught me the correct way to use it. Big thanks.

I bought it and it works great, you can actually set it up by feeling the mouth of the case hitting the bottom of the collet too. There is not any damage to the bullet whatsoever and I pulled different types of heads, doing a ladder test for seating depth or powder charge makes this tool a must have!! No more hammer for me…..

Being new to reloading I'm making a lot of mistakes. After using some long nosed vice grips to pull the bullets, I figured there had to be a better way. I followed the instructions in this video and with a little adjusting got the bullet puller to work flawlessly. If you are marring (grabbing) the case instead of grabbing the bullet, try backing off the top adjustment. I am now pulling bullets from error cartridges without destroying them. Thanks Hornady!!

Great product once you have sorted it out, used it on 25-06 and 222 worked flawlessly and projectiles were not marked at all

I’ve been trying for a day to get this to work on 300 blackout. I follow the instructions to a T and the cam grabs the brass, not the bullet and will not work. Any suggestions?

Got mine by 8am the next morning via Amazon. Great place to order it from

Excellent video. Thank you!!!

Or the other end of the “why pull the bullets: scale. Yesterday, I found out my scale was way off and wasn’t sure if the powder in the 50 cartridges I loaded last week were effected. Why take a chance. I pulled all 50 with this bullet puller with no problems.

My RCBS bullet puller arrived today. I have thirty 45- cal ACP rounds to pull. I didn't put enough Titegroup powder in them - they won't cycle my PPQ 45 pistol. 4.4 grains of Titegroup wasn't enough. 4.8 gr of Titegroup cycles the pistol.

Here’s the thing. The cam lock die doesn’t have enuf thread for it to sit high enough so the ram can go all the way up, it probably work better on shorter cartridges. So a lot of guys are saying it kept on gripping on the case than the projectile becuz when the ram goes all the way up the case enters the collet. The a dumb but easy solution to fix the frustration: sit your cam lock die all the way into the bushing so the bottom is flush with the bushing, now from underneath you can see the bloody collet open and close when you work ur cam lever. Visually determin when the bullet is sitting into the collet deep enuf, hold onto ur ram handle and now pull the cam lever from 45 deg angle down to flat so collet closes and grips the projectile. Lower the ram handle and work is done. This is better than guessing what a longer cartridge is doing inside the die and then it grips onto the case. Very frustrating.

great tutorial... thank you

This thing is tricky to use, but I found the trick is NOT to "cam over". Just pull it over enough to grab the bullet. And on .308, which is what I was doing, everything has to be opened up all the way. The die seems to be short for longer cartridges. It is pretty counter intuitive to what we are used to, but at the end of the day, it is better than the hammer.

iam having problems pulling 7.92x33 iam using 8mm but it keeps slipping off the bullet .ive tried the hammer puller and it fails to drive the bullet off? these are my reload mistakes not military or factory

Watched several times to make sure I was setting this puller die up correctly and still wrecked several kind of rare 6mm ARC cases trying to troubleshoot this thing. Not often I say this about Hornady reloading equipment, but this thing is junk, at least on smaller cases, back to the hammer.

I can't for the life of me get a hold of the cam lock die body. Does anybody have the part number for it. This search is driving me nuts

The 45 ACP collet broke the second time I used it. Really thin on material, my 5 other calibers work great.

Just got one from. Academy Sports but no collets,been trying to own this product,help

This thing is a PITA. I get the edge of the brass more than the bullet itself and I followed the directions to a tee.

Try it using 50 grain 22 bullets or 204 bullets. I cannot get the collet to release the bullet. PITA>

Will this work on a dillon 550b?

Take a shot everytime he says " GO AHAEAD " LOL

It's pronounced Hornady. Not Hornaday.

THESE SUCK IF YOU WANT TO USE THEM ON .223 55gr. + - They just don't work so don't waste your money

Hornady, you might as well stop making these videos. When you tried to force the shot on your employe’s as a condition of employment you lost a lot of customers. I won’t buy anything else from you.

Oh! Hornaday didn't get the word. We're not buying any more of your products after you lied and tryed to manipulate your own employees. There are plenty of other companies that make what you make. So once again( listen up this time )..... Good By!!

Please, please, please stop saying “go ahead and…”. It adds nothing to the context and is just a waste of time. Otherwise…great video!