How to install the Mtake for the 2022+ Honda Monkey.
Пікірлер: 26
@unclefester5418 Жыл бұрын
I just fitted one of these to my 2022 Monkey. Easiest way I found was to remove the injector with hose attached, from the manifold. Remove the throttle cables, remove the complete throttle body / inlet manifold, and the assemble the new intake onto the manifold while on the bench. Fit the intake air temp sensor and connect the wiring to that sensor. Refit the complete manifold and intake assembly onto the engine. refit the injector, refit the throttle cables, and reconnect the wiring to the TPS and injector and last of all fit the new Air filter to the new intake. Trying to assemble it while still on the bike is way too difficult to get right. To add context to this I have in excess of 20 Honda Monkeys that are highly tuned and approximately 40 years working as a Mechanic. Very happy with the product, but the fitting instructions leave a bit to be desired, so I hope what I have written above helps someone fitting one of these intakes.
@Silence-and-Violence3 ай бұрын
I need to find a way to save this for like a year from now.
@danteisthe1 Жыл бұрын
This install was a pain in the ass! I can do it much faster now, but it took way too long! A proper installation video would have prevented wasting a bunch of time! For the love of god help your future customers out and make a better installation video!
@billwilliamson98422 жыл бұрын
I pick up my black 2022 tomorrow wooohooo!!!!!!! Can't wait to start moddin it. cool music in this vid too
@xgeska2 жыл бұрын
Actual video vs video of static images would be more helpful
@Silence-and-Violence3 ай бұрын
Budgeting for next year and honestly kinda suck at mechanical stuff compared to average rider... Does this have anything over the DNA dual exposed intake that you guys describe as an easy install on your website? Im wondering if I go DNA just to avoid the install nightmare... a veteran mechanic is saying it's harder than it should be.
@mnnthbx3 ай бұрын
Both units will perform the same. It's a matter of style, budget, and patience....
@Silence-and-Violence3 ай бұрын
@@mnnthbx thanks brother. I prefer to support mnnthbx products whenever they are superior or very close... But I am a shitty wrench and I hate asking a handier buddy to get annoyed over it too. I have some handier friends, but not true motorcycle or wrench vets. I might have to spend more to avoid the headache.
@brianhoward92172 жыл бұрын
Great vid, hope to use it when I get mine soon! Thanks! Cheers from Australia.
@Donkeydoodoo422 жыл бұрын
What's the torque specs for the manifold bolts
@chrissomers58592 жыл бұрын
What do we do with the second breather hose that is removed from the factory air box?
@mnnthbx2 жыл бұрын
Crank vent goes to the included Uni filter. Gas vent goes to atmosphere.
@promykzpolski Жыл бұрын
do you have in stock yet ? if no, when i can buy it ?
@mnnthbx Жыл бұрын
In stock….
@promykzpolski Жыл бұрын
@@mnnthbx ok, but the website says that it is a pre-order, btw can you tell me if yoshimura rs-3 full exhaust for monkey but from 2022 are produced and are they in stock?
@scatmancrothers1127 Жыл бұрын
I cannot for the life of me get the air temp sensor installed and connected after getting the intake on. There is just no room to get the sensor onto the bracket and then plugged in.
@mnnthbx Жыл бұрын
Make sure the wire is routed between the mounts as shown in the video. It will fit FOR SURE.
@erwinito12 жыл бұрын
Just got mine- so no issues with the sensor being outside ? I ride the bike off road every now and then-
@mnnthbx2 жыл бұрын
None. It's water proof. We design all of our intakes with it out of the runner.
@erwinito12 жыл бұрын
@@mnnthbx super- thanks for the answer. Can't wait to put it on this weekend. Cheers-
@3rdofthree2 жыл бұрын
Can this be on 2021 model year?
@mnnthbx2 жыл бұрын
No. We have a specific intake for your bike on our site. Just use the make/model/year search function at the top of the site to pull those options.
@jeremybrunan12182 жыл бұрын
Great video, but the install is a BITCH! So tight and getting the intake on the carb wasn't fun. It didn't want to go with that big O-ring that was included. Had to go with a tighter fitting O-ring and put a plastic razor blade between the half runners so it would slide on easier then pull the plastic out to tighten. Not a fun install, but you were the first to market with the intake so I went with it. Thanks for the video.
@mnnthbx2 жыл бұрын
It’s a tight space for sure, and not overly easy, but it sounds like you went about it wrong. The o-ring goes on the throttle body first, then you bring in the aluminum halves from the sides and tighten. That part isn’t hard. If you tried to connect the two halves then get theM pressed onto the throttle body, I’m sure it was a nightmare…
@jeremybrunan12182 жыл бұрын
@@mnnthbx I did the O-ring first, but tried sliding on the intake partially together on to the carb which was probably my problem. It seemed harder for me doing the halves separate so I did it partially together. BTW- where do you route the tube from the bottom of the gas tank.
@mnnthbx2 жыл бұрын
Just route it down and vent to atmosphere. It has no place in a proper intake.