How to Adjust & Tune a Chainsaw Carburetor (Fixes Bogging | Hard Starting | Poor Performance)

  Рет қаралды 128,369

Helping U online

Helping U online

2 жыл бұрын

How to Adjust & Tune Up a Chainsaw Carburetor. Doing This Fixes Bogging Down, Hard Starting and Poor Performance issues.
In this video you will learn the easy steps to take to properly adjust and tune up your chainsaw carburetor for maximum performance.
Caution:
If you choose to adjust the H (High) side carburetor setting be very carful not to set the rpm's too high. If you do you run the risk of overrevving the engine and causing damage to the internal parts. If you are going to make the high side adjustment be sure to have a tachometer available to measure the rpm's and check your owners manual for the appropriate maximum setting.
*If this video was a help to you give it a "thumbs up". If you have not already done so, please consider subscribing to this channel.
Disclaimer:
Although I have been following these procedures for many years; I assume no liability for any damage that may occur to any person or property as a result of the information provided in this video. I take necessary precautions (that I am aware of) when working on these projects but that in no way implies or creates any expressed or implied warranty or guarantee of any kind of particular result. Any injury, damage or loss of any kind to anyone or their property or anything related to information in this video is the sole responsibility of the user and not Helping U Online (this video).

Пікірлер: 30
@dewanehill1435
@dewanehill1435 2 ай бұрын
Outstanding!!
@annaaron3510
@annaaron3510 Жыл бұрын
Nice chaps.
@01butenkieler30
@01butenkieler30 15 күн бұрын
Have to try it out😉
@Amarillobymorning777
@Amarillobymorning777 2 ай бұрын
GR8 explanation
@helpinguonline
@helpinguonline 2 ай бұрын
Thanks
@George-iu7sz
@George-iu7sz 4 ай бұрын
You know, you started off great. Your saw had exactly the same problem as mine. Bogging down (and THEN) difficulty starting. The problem is the you skipped all that and jumped to where your saw wasn't bogging anymore. That was EXACTLY the problem i'm trying to solve and you skipped it !!!!! I can't "warm up my saw" because it won't stay running and is hard as heck to start. This is VERY frustrating.
@jsprague1988
@jsprague1988 Ай бұрын
he literally explained how to turn them. lmao
@jonpatrick66
@jonpatrick66 2 жыл бұрын
Thank you.
@dsnx2
@dsnx2 2 жыл бұрын
Thank you
@helpinguonline
@helpinguonline 2 жыл бұрын
You're welcome
@keithtuck4743
@keithtuck4743 8 ай бұрын
He knows my feelings
@dieseldavebrown
@dieseldavebrown Ай бұрын
I have 4 stihl chainsaws and numerous deivces with small engines- 2 and 4 stroke (my preference are honda engines) and I have replaced numerous carburetors and I have been seriously thinking about buying a seperator and removing the ethanol from the high octane gas. The ethanol in my opinion is the main culprit though I agree any gasoline siting in the carburetor can cause problems (I usually shut off the fuel first and let the engine run out of gas.
@highwatercircutrider
@highwatercircutrider 11 күн бұрын
Stop using ethanol fuel, it will eventually damage you engines and carb’s seals. Buy recreational alcohol free fuel and even then completely drain its fuel after use.
@Bryan-wq9vq
@Bryan-wq9vq Жыл бұрын
😊 I can't warm it up if I can't get it started
@genesmay6589
@genesmay6589 9 ай бұрын
Turn the high and low both in till the just seat and back them off 1.5- 2 turns and go from there if it's indeed a carb issue and not a fuel, spark, spark plug etc issue..
@Vacrie
@Vacrie 6 ай бұрын
@@genesmay6589what about the idle?
@jacobcarraway1989
@jacobcarraway1989 5 ай бұрын
If you can't get it running, more than likely, your L screw for idling isn't adjusted properly. I just had to adjust mine this morning as the saw was wide open on idle. I found a sweet spot in between where it wanted to die and before the chain started to turn. I haven't really had to mess with the H screw but might need adjustment if there is issues when cutting.
@wrangler6977
@wrangler6977 Жыл бұрын
I am surprised that there was no mention of checking the air filter. If it is clogged up you will not get enough air to mix with fuel to start or run properly.
@daultonruff2281
@daultonruff2281 Жыл бұрын
Hope this works. After 3rd trip to Jensen Pilligard I need to fix it myself. The draining is the screw up I made. Due to surgery I just let the saw set for a couple of months, which I promised myself I would not do. Thanks for your help.
@helpinguonline
@helpinguonline Жыл бұрын
thanks for your visit.
@haroldnorthern1230
@haroldnorthern1230 Жыл бұрын
Bubble burst ! My 017 stihl only has 1 adjustment which is thru the handle bar my ? Is which way to turn it to lower idle speed can't do the thru bar due to its not lined up right have to remove filter to assess carb
@markxrocksollidptofit
@markxrocksollidptofit Жыл бұрын
🙂
@rightsideofthegrass8114
@rightsideofthegrass8114 2 жыл бұрын
If the H screw has been changed,where to start. you gave info about L and LA (screw in to bottom, the 1 1/2 turns out as start points, but said nothing about H. I have a 210 that I cannot get started - never reach the point of fine tune. New carb and ignition module only a few service hours ago. It would run for 20 minutes, then stop, unable to get it started. screws have been changed, now unable to start. Ideas?
@BiggerAlan
@BiggerAlan 2 жыл бұрын
Did you double check to be sure your getting a good spark after you replaced the ignition module? May just have to continue playing with the H screw, turning it out 1/8” at a time. Don’t give up..
@willyfromthehillies
@willyfromthehillies 2 жыл бұрын
Start with H all the way in, the m. Back out 1 full turn
@bluntforcetrauma2141
@bluntforcetrauma2141 Жыл бұрын
That was my problem too. Will see what happens
@breckfreeride
@breckfreeride 3 күн бұрын
High altitude tuning is a bear... 9600 asl. Just getting it to start takes alot of monkey business.
@dukecannon2161
@dukecannon2161 Жыл бұрын
adjust high speed screw to no load max rpm..then saw will have perfect highspeed mixture low speed helps with how it responds when you suddenly whack the throttle open...you are no mechanic
@bluntforcetrauma2141
@bluntforcetrauma2141 Жыл бұрын
So keep it all the way counter clockwise?
@genesmay6589
@genesmay6589 9 ай бұрын
​@bluntforcetrauma2141 start it squeeze the throttle completely and adjust the H at full throttle till it runs smooth some say turn a quarter more after you find the best spot you'll hear it.
CORRECT WAY To Adjust Or Tune The Carburetor On A Chainsaw (Step-by-Step)
11:49
Steve's Small Engine Saloon
Рет қаралды 2,9 МЛН
How To Tune a Chainsaw
5:53
HowToLou
Рет қаралды 36 М.
Luck Decides My Future Again 🍀🍀🍀 #katebrush #shorts
00:19
Kate Brush
Рет қаралды 7 МЛН
Дибала против вратаря Легенды
00:33
Mr. Oleynik
Рет қаралды 3,1 МЛН
버블티로 체감되는 요즘 물가
00:16
진영민yeongmin
Рет қаралды 63 МЛН
Stihl MS 170 won’t start . Chainsaw won't start or stalls.
20:01
Kyle Hall woodworker
Рет қаралды 53 М.
How To Adjust / Tune a Chainsaw Carburetor | Husqvarna Stihl BEST Way
4:14
The Uneducated Outdoorsman
Рет қаралды 371 М.
HOW ADJUST CHAINSAW CARBURETOR:  Chainsaw Carburetor Settings Explained!
13:34
TheRepairSpecialist
Рет қаралды 1,5 МЛН
How to tune a chainsaw carburetor
14:17
Dyno Joe Mods
Рет қаралды 53 М.
STIHL’S OFFICIAL 2 STROKE CARBURETOR TUNING PROCEDURE.
5:56
Vintage Engine Repairs
Рет қаралды 173 М.
98% Make This Chainsaw Sharpening Mistake (Even The Pros)
12:54
KERF Tools
Рет қаралды 2,1 МЛН
HOW TO ADJUST A CHAINSAW CARBURETOR WITH NO SPECIAL SPLINE TOOL
8:09
Bob's Lawn Service & Plowing
Рет қаралды 218 М.
CHAINSAW CARBURETOR TUNING: For Correct Chainsaw Carburetor Operation!
2:50
TheRepairSpecialist
Рет қаралды 102 М.
Qual Fita NÃO vai Me AGUENTAR😱 #shorts
0:45
Lucan Pevidor
Рет қаралды 15 МЛН
Final muy increíble 😱
0:46
Juan De Dios Pantoja 2
Рет қаралды 35 МЛН
это самое вкусное блюдо
0:12
Katya Klon
Рет қаралды 1,7 МЛН