Today I show you how simple it can be to align the mirrors on your co2 laser cutter / engraver while speaking plain English #howto #laser affordable mirrors I like amzn.to/3PNY8r7 lenses I buy amzn.to/3pIpnJ1
Пікірлер: 46
@user-xw5gj4sk2n Жыл бұрын
I have watched countless videos and spent what seems like half of my life and a few rolls of masking tape trying to get my OMTECH 60w aligned correctly. I was so frustrated that i had all but given up and thought oh well that will do. Your video makes alignment so simple and i now have perfect alignment in less than 15 minutes. Can't thank you enough
@JaysToDoList Жыл бұрын
I am glad I could help
@agunjal2 жыл бұрын
Thank you thank you.....After trying for 7 hours I was ready to sell my laser.....With this method it took me less than hour and my laser works great
@JaysToDoList2 жыл бұрын
Glad it helped I remembered my first time this is the reason I make the videos trying to help out however I can have a great day
@bigfranksworld10 ай бұрын
Yes, this seems much easier than some of the other alignment videos I have watched. Thank you!
@JaysToDoList10 ай бұрын
Thanks for watching im glad I could help
@chrisl49996 ай бұрын
Excellent alignment vid. I had never considered bulking the tape up and using it's semi-transparency to verify alignment. Nice.
@JaysToDoList6 ай бұрын
Thanks hope it helps
@onesmarthome Жыл бұрын
Wow you are a lifesaver! I literally spent all of yesterday aligning my Omtech 55W and thought I had it really dialed in. Following your instructions, within 15 minutes found that it was close but not quite and had it completed shortly after. Thank you for sharing this technique that was shared with you!
@JaysToDoList Жыл бұрын
Thanks for watching alot of people over complicate alignment glade you found this helpful
@rusu9596 ай бұрын
very well done! great job and thank you for the tutorial
@JaysToDoList6 ай бұрын
Thanks
@frankgarcia46443 жыл бұрын
Awesome instruction with the layers of tape. That will make aligning the mirrors easier. Going to try today. I’m currently having an issue as you described with the machine not cutting well on the right side of my bed. I’ve found getting the alignment from mirror two on to mirror three difficult to stay on the mark when moving the head from the far left to the right. Hopefully this method will help out. Thanks for the info.
@JaysToDoList3 жыл бұрын
Great I hope this helps the masking tape idea really does help you get alignment in much better and faster
@VillainCrew Жыл бұрын
Did this fix the issue of not cutting properly on one side of the laser? I am having the same issue and before I tinker with it was just curious
@JaysToDoList Жыл бұрын
This can be one of the problems with it cutting better one one side then the other
@matbell151410 ай бұрын
Thanks….much appreciated
@JaysToDoList10 ай бұрын
You're welcome!
@fernandorevilla4 Жыл бұрын
Thank you!!! Great video!!!
@JaysToDoList Жыл бұрын
Thanks
@karabritch78343 жыл бұрын
Great info!
@user-lk2gl8qw1q5 ай бұрын
mirror 1 to 2 spot on. mirror 2 to 3 if i move the mirrors close to each other and get it center then when its far away its off by alot. if it hits center while far away then it will no longer hit the same spot when i move it back close. Any recommendations?
@JaysToDoList5 ай бұрын
Do it again your machine must of been off alot
@frankabbott2326 Жыл бұрын
i have a OMtech 55 watt. i have really messed up the alignment. I adjusted mirror 1 for no particular reason other than I assumed that's where to start without reading any instructions. I found your video and its not evening helping due to my stupidity of playing with the first mirror. I have adjusted mirrors 1 & 2 and align them but they are so off kilter to what the originally looked like that its impossible to adjust mirror 3. its so far off i cut through my air hose!! Is there a way I can go back to basics with mirror one which i am positive was the stat of my problems. Any help would be greatly appreciated as i am totally stuck and have spend another hour today and am back to square one. I am completely defeated. Thanks
@JaysToDoList Жыл бұрын
Start with the mirror closest to the laser tube then follow my instruction in the video mirror closest to the laser tube is mirror 1 the move to mirror 2 then 3
@speedybeak Жыл бұрын
I’m very confused on my adjustment. If I have the tape close to mirror one I hit center, I adjust the nozzle to the front (left) mirror 2 and I hit center. Well when I move the laser to the far right by control, mirror 3. I am hitting high. I don’t know how I’m supposed to adjust mirror 2, to hit correctly to 3, without having to adjust mirror one back to center. Any help would be awesome
@JaysToDoList Жыл бұрын
move mirror 2 covered in tape close to mirror 1 by moving y axis all the way to the back of the machine and pulse it should hit about center then move y axis all the way to the front of machine as far away you can from mirror1 fire again the two dots that it crates on the tape should line up on top of each other if it is not lined up adjust mirror 1 until it does do not move to mirror 3 until mirror 1 is fully aligned to mirror 2. then repeat on the x axis between mirror 2 and 3. please watch the video again it spells this out better
@speedybeak Жыл бұрын
@@JaysToDoList so I have mirror one and 2 spot on. So if I move mirror 3 all the way by controller, then it’s hitting high. So can I adjust mirror 2 to where it hit mirror 3 accurately? Because once I adjust mirror 2 to hit mirror 3, then doesn’t that mess up where mirror one hits mirror 3?? Idk if that makes sense
@JaysToDoList Жыл бұрын
@@speedybeak mirror 1 is the one back by the laser tube and mirror 3 is the ono above the nozzle I am just making sure we are talking about the correct mirrors. Adjust mirror one so it aligns with mirror 2 close then far. Once the burn marks line up move to mirror 2 to 3 adjust mirror 2 near then far from 3 align the burn marks by adjusting mirror 2 that will not affect the adjustments on mirror 1
@J.M.19538 Жыл бұрын
hello, please i have a problem with mirror 2, at the start of axis it shoot into center of tape, but at the end of the axis it absolutely does not shot the mirror at all... and i dont know how to set it... im pretty desperate from it already
@JaysToDoList Жыл бұрын
Move mirror 3 away maybe 25% the distance from mirror 2 try again get it to about center then move it 100%away ir should hit the tape so you can align it perfect. Be careful that laser beam can burn you when you don't know where it is at
@J.M.19538 Жыл бұрын
@@JaysToDoList i sucessfully set laser beam into mirrors.. but.. the 2nd and 3rd mirrors pulse at the start of axis hits the center of mirror, but end of axis hits a little bit next to first pulse, but laser beam from nozzle is right now perfect... is that a problem ? i mean those mirrors, or is it ok ? differences are about 1-2 millimeters
@JaysToDoList Жыл бұрын
It will most likely work now but you should have them on top of each other. The 1mm difference could cause some power loss or make your Laser cut better on one side then the other
@J.M.19538 Жыл бұрын
@@JaysToDoList i would like to set them on themselves on both sides, but i spent already a whole day on that and im glad i get at least this :D i simply cannot get them on each other, because when i move left/right, on the start of axis it moves just a bit and on the end it moves even for 1cm well its not easy, but thank you for advice :)
@hrothgarshoard46563 жыл бұрын
It is very unhelpful when the mirrors are pretty much aligned to begin with. Start with something out of alignment and help work through the problems that might occur. I'm off by probably 5mm from left to right and no amount of micro adjustments is making any difference. This does not help me learn how to make those adjustments.
@nikkicork88152 жыл бұрын
Hear hear! Good effort making the video but little effort applied to help 1 2 and 3 alignment problems
@JaysToDoList2 жыл бұрын
It is the same process just adjust the mirrors slightly more
@derek2593 Жыл бұрын
Lol, "pointless" red dot. Mine broke off when I was cleaning the lens. I consider it an "upgrade". Just a confusing, cumbersome, hassle anyway.
@JaysToDoList Жыл бұрын
Yea I thought on my first one you had to have them I see I was wrong
@antoniokfranco3 жыл бұрын
a video would help if mirror 2 does not align from back to front and how to solve that. thanks
@JaysToDoList3 жыл бұрын
Yes you will need to align all three one adjustment throws them all out
@antoniokfranco3 жыл бұрын
@@JaysToDoList. I put in a new tube and I am unable to align mirror 2 . I have one high when mirror 2 is at the back and in the middle dead center at the halfway point, then low when mirror 2 is all the way front. I think my laser tube needs adjusting?
@JaysToDoList3 жыл бұрын
Oh I see you may need to level the laser tube
@taylorlanter49952 жыл бұрын
Modus did you ever solve this issue? I am trying to get a brand new unit aligned and I get it dead on with the gantry back then move it forward and am barely in the circle. I am a noob to this and it's stressing me out
@antoniokfranco2 жыл бұрын
@@taylorlanter4995 this procedure can be completely frustrating. I eventually figured out the proper alignment process by watching this video. kzfaq.info/get/bejne/qL-IY92XvKzSeYE.html