The measure mistake and recovery was excellent. It show the viewer that it happens and how to fix it. Good job.

Great simple to follow video! Great Job!!!

thanks for making these and making them realistic - it's so helpful to see how you fix little mistakes.

Thanks again for your video I am learning from you. At work really no ones want you to learn 😒. You are awesome.

I love your videos 👍 thank you very much for let us know your experience in this field

Hi , thanks a lot for teaching every day new steps To install the tubing . Very interesting. Congratulations

Extremely useful content. Thanks a lot.

Good stuff, love the little tricks

Great video. Very helpful

You are very talented

Thanks for posting!

If you're doing a lot of this at a time, a bandsaw will save so much time and effort. Also, using the knockout furthest from the stud gives you a bit more angle & clearance when sliding in the pipe, especially if it's a tight fit 😉

Very nice video mate.Keep up the good work.

Appreciate you leaving in the errors because those are the things likely to bite a new person attempting this!

Good work i love yr video i'm electrician too we many diff zbout that because here in morocco we use 230 v to 400v ac voltage

More vedieo it's really helping as thanks so much.

More videos like these please it's helping a lot 👍

Great job!!!

Thanks, very helpful. I'd like to see how things are usually routed at the panel with lots of conduits.

Put connectors on pipe then stab in box, make your life much easier.

Excellent videoz

Could watch this all day 👏🏽

Very good thanks

He is right when he stated, "he wasn't thikin". He does have only one bit, too large? Good thing he is in construction.

good job

YOU HAD ME AT 16' FAT MAX! excellent video

Thank you!

Hello coming from Michigan I'm used to Romex. Could you do a video on the type of wire ran through the conduit? Thank you for the awesome information!

thank you😃😀

You are good dood

Nice

Thanks

Great videos. Howbout making a video on installing conduit on a block wall building. Thanks

The 1” depth mark for the offset should be placed onto the arrow, for those who didn’t know.

Another brutal video.. 😂 2 for 2

I use an abrasive chop saw to cut conduit its a game changer

More conduit bending please

Hey Bob, Does the code allow for a power inlet box (used to install a portable generator for emergency power) to share the same conduit with another line so I only make a single hole into the house? In other words, I would like to run a 120 amp service out to a single exterior outlet served by it's own dedicated exterior enclosure separate from the power inlet box. Both circuits would be on their own dedicated circuit breakers. A single pole 15 amp breaker for the exterior service line and a 30 amp breaker using a generator interlock kit. I would like to avoid punching 2 holes into the wall near the electric panel to keep things looking tidy. (I'm following the "fill" rules regarding the number of cables inside the conduit) Thanks in advance.

1/2" conduit bend is 5" not 6"

3:00 drills own leg

Do you ever need to make a 3 or 4 point saddle bend?

Ideal benders are the best ones. Made to be used by right handed and left handed. Not like the greenlee ones.

What do u do if there already is an installed conduit but you want to move it?

Nice video. 9:30 next time, just drill much bigger holes in the studs. Prevents small measuring mistakes. 😏 Or.. you could do the piping first, and then screw the box on the stud. This way you will punch the best knockout on the box. Or.. you could do like you did, but with the connector on the pipe, rather than on the box.

How do you set up conduit at the corner of the house?

Instead of ruining a good pair of channel locks, you could also just buy a reamer which is faster too since it reams the inside and outside at the same time. I also use a cordless Milwaukee bandsaw to cut my pipe and I realize that people may not have the money for a tool like that too but it makes everything so much faster and easier.

Who the heck is getting the coupler and connecter backwards there Bobby Boucher eh? Haha

I gave my first 1k like

Does some code require the type that screws together?

Why no rubber bushings/end caps at the end of the pipes? Are they not needed?

Best tool I have but never used that much for conduit the makieta 9.6 one handed Sawzall from the late 1990s. I'm sure the tool works but Batts don't hold a charge I mean nicades from late 90s lasted till 2010( cld have been longer but they were lent out to someone who didn't know nicades need to be cycled I got them back 2013) was pissed had no clue where my drill 12v went. Batts no longer hold acharge. Cld buy new Batts but haven't used in 15 yrs

stub for 1/2 is 5

For that second bend on that offset, the 45. why didnt you bend on the arrow? I always do offsets on the arrow. Just wondering, I like understanding different ways to do things

Show you actually pulling the wire after running the conduit

I want it done with one piece.... no couplings !

Why don't you use wheel cutters?

For my own home, I’d build it using conduit even if it isn’t required in that jurisdiction. NM is trash.

Like on texas they use cheap materials

Really struggle

? No levels or proper measurements?

Please your video’s show your inexperience with your conduit bending . I would not let my students watch this video with its error’s . First comment to anyone and you need to be thankful it is a shed and not a house.

5 inches for the 1/2 conduit. That’s why your math was wrong. It’s important to know what you’re bending !

First step: get a proper drill bit

At 6:50 he's using blueboxes ????

When in doubt hog it out (the hole). Not very accurate. And bend was not 90 degrees

So I spent 200 on a bandsaw just to do the same thing you’re doing…I’m annoyed lol

They never make u use emt in residential. I'd like to see this guy's license. It's highly illegal to do electrical wit out a master electrician license, contractor license, insurance and bonding. Don't get taken for a ride.

LOL still need more practice to post videos.

Were you held at gunpount to make this video?? No excitement whatsoever lol.

You are not a good electricien, i seen enough