Please don’t forget to subscribe for more content !!

2:15 Mr Bug stopped by, assessed, and approved this video.....

Great technique but I kinda lost it when the audience started clapping 😂😂😂

fast and easy! Thank you!

Thanks for that. You make it look easy

Thank you man this worked nicely

Looks like the concept may work on smaller tires. With an assistant. I tried this with an aluminum Snap-On jack by myself on a 37" Super Swamper and was a no go. Steel jack is a must as mine kept lifting even with me standing on it.

It really works best When you break the outside beads first. Then the inside beads. Regards :. Longtime rider!

Great video. How about one on rebuilding the tailgate, motor, tracks and weather stripping.

$60-$80 to just take them off? Where do you live at ? $20 & a 12 pack for 4 wheels is going rate around here plus I got a 5 gal bucket of old lead weights for molding sinkers. Providing Id mold some sinkers for the 2 guys there that fish. 👍🏻

Often time these long straps have cuts and nicks in them and need to be replaced. If you have one that needs to be replaced or find one at a yard sale; you can cut it shorter and have a strap that is easier to work with on tires and such. Praying for your safe travels.

LOL. Breaking one side bead is no big deal. Now get the tire off the rim!

A hilift Jack with the base removed works excellent

Thanks. Not sure if you needed to do it on both sides but I had a hard time sawsawzing the tire completely to split apart I only broke bead on one side but I think it would of been easier if I flipped it and did the other side

Do you think the jack stand pressure on the sidewall, squeezing the tire in a small area, damages the sidewall cords inside the tire? I need to replace all 4 cracked valve stem and reuse the tire? Also, do you think a 2 ton floor jack will work?

Ugh, dang it! I broke the bead and I could see it was off the rim with my own eyes. But when I let the pressure off the jack and unstrapped it, it reseated itself! The sidewall seems to have a ton of flex, so instead of peeling away around the rim, it just unseated at the pressure point of the jack head and slid back into place. I've had some that were easy peasy and others like these two off a trailer. The worst were ATV tires. After the better part of a day where I even tried to break the bead using the edge of the bucket on a front end loader, even bouncing the weight of a 60 hp diesel + tractor frame + the weight of the loader itself across the bead outside the edge of the wheel, I finally gave up and took them to a shop. It's a little exasperating to think about how much of my life I've wasted on the ones that needed their press. If I had a do-over and the shop space, I'd have just bought a good quality machine, primarily because I live in a rural area and the travel time plus fuel is an expense and chore in itself.

Can I use this method if I’m keeping the tires just getting rid of the rims.

The applause was hilarious

Excellent explanation. Great video

If you waived your strap into the rim hole and around the shaft of the jack wheels and back through the rim hole and then lock the straps then you wouldn't need an assistant

That’s a very good way to break the bead of a tire, another way you might like using a scissors jack and put the tire on the ground under a high enough or lifted up vehicle and place the jack on the tire and raise the jack to hold on to the vehicle chassis to create the force to push down the tire to break the bead

That was a fucking good one hope it works

Followed it to the T but the tire refused to be removed. It’s like it’s cemented to the rim. I even had help. Should I just take it to a shop at this point? I’m broke af.

Great video! Although I have to say, the moral of the story is, don't be poor...

tractor and a bucket culd work to mabye

this was recorded Infront of a live studio audience

Sandals and white socks lol

Looks like it would work but there's way easier ways to do it. I can't believe that you put your hand down there to check the bead. Shit happens.

Now the hard work comes you didn't show how you got to get the tire off the rim you just did the easy part time for the breaker bars and a lot of muscle getting that complete tire off the rim you just broke the bead😊

Bringing back socks with sandals, what what what

no holes in my wheels.

It takes you 5 mins?

DIdn't work for me. Tried several times, no luck. Bead is just too stuck

A lot of work there. Maybe there's an easier and less time-consuming way?

It's time consuming that

The video does not show critical angles of how the technique works . Thankfully I found a much better video.

Thats the easy part, the part everybody wants to know is how to get the tire off the wheel. Your not cutting the bead with a Sawzall

All that to save 50 bucks. No thanks

Thank you, but no.

Way too hard. There are easier ways that don't require equipment most people don't have. 2 people? You've got to be kidding.

You talk too much