Great video. Very detailed. Thank you. 🤝

I've been on the fence about if I should buy or hire or build a shed myself. I've watched a bunch of KZfaq shed builds and there's a lot of bad advice out there! This is the first video I've seen that shows how to properly build a shed with structural integrity and explains the framing process in a way I can duplicate. This video has convinced me to build my own. Thank you my friend!

Good video. Something I see wrong a lot on roofing shingles is the starter. How you are supposed to use 3 tabs as starters is install them so the tabs overhang the drip edge, so the tar strip is right at the edge of the roof, then cut off the tabs. This puts the tar bond right at the edge to hold down the field shingles. Otherwise, you're leaving 5-6" of wind lift area right at the edge which can and will lead to wind damage to the roof. Also, and this is just nit-picky, the drip edge is supposed to go UNDER the felt at the eaves and over the felt on the rakes. Again, this has to do with wind driven rain: at the rakes, if wind pushed rain under the shingles, it'll go over the drip, onto the felt and run down, and if the felt is over the drip at the eaves, it runs off the top of the drip and out, never getting to the sheathing. Then the argument that wind could drive water under the shingles and felt at the eaves, well, if the starter is nailed down correctly, and the shingles are overhanging 1", then the wind would have to overcome gravity to get it under there, but that could be mitigated by tarring down the drip to the sheathing before the felt. All that to say, that is SUPER overkill for a shed. LOL But the wind lift at the eaves and rakes from the starter tar bond not being at the edge still holds. Good job overall, and again, the way you roofed it is the way most carpenters do, but just like everything, there is a better way that doesn't take too much more effort to do, if you know to do it. I do roof inspections for a living. Have a great day! Looking forward to more content.

Thank you... You do a great job filming and explaining. Well done!!!

You mentioned turkeys and ducks but not the deer walking behind ya the whole time lol great video 🤙

Thank you bud!! I’m building mine based off of your video!

Awesome shed, y'all. It's always good to hear home folks explain something. Thanks for the share.

good stuff fun to watch

Awesome 🥰🥰🥰

Man I've watched a lot of shed building videos and this my friend is GREAT!!!! You were so thorough in explaining things, especially how to hold ridge beam in that saddle.. Thank you for sharing your skill.

Great video fellows

Nice, I used to be a roofer, we never left just a small piece on the edge?, I guess it will stay with Flex tar..., and, you did not use level on a door, wonder, why?? Other than that, OK video ;o)

Time for new nailer😂. Good video.

nice job

That Flexshield will help a lot when the shed washes down the river.

Great video brother. A job well done by you and your crew. Glad to hear the Lord is blessing you 😊 God is good all the time and all the time God is good. Stay safe and keep growing in your faith and in your knowledge of carpentry/construction. Put God first and everything else will fall in line.

Good video. Thank you. I will be building one for myself this spring. Biggest concern is getting the rafters correct. That's the only part I have no experience with. This was very helpful!

I wish you had shown cutting the rafter beams, but other than that great video.

The pad was level without any extra work?! Did you buy a lottery ticket after work? :D

Did you feel that using 2x4 at 24" centers was strong enough?

Do you by chance remember just the cost of material's only .Thx !!!

Curious....on this build what exact measurement are the 2 x 4 wall studs...?

How do you keep the building from just sliding off the block foundation it's setting on?

Parts list quantity of each board needed? For this exact build. Tia

How did you cut the rafters?

If you don't mind me asking, how much watch time did you get on this video? I'm considering releasing my tutorials in this longer format