How to build a MILD small block 350

No video

How to build a MILD small block 350

Рет қаралды 337,766

Theblackcarguru

Күн бұрын

Пікірлер: 634

@SoylentGamer 6 ай бұрын

Mild builds are underrated. An understressed V8 will give you many miles of smiles.

@misfit1x444 5 ай бұрын

Yeah you don't need a bunch of horsepower to have fun 😊

@user-hm6iq6sj7i 2 ай бұрын

Exactly I agree

@95Sn95 Ай бұрын

One of the funnest cars I've owned was back in the early 90s it was a beater 76 nova SS a total day 2 type car it had an old tired 350 with a crane 268 Energizer cam long tubes dumping in front of the rear tires and a Holley on a factory cast iron intake if I remember right, it had a 3.31 gears Camaro 12 bolt posi with 235/60r14 rear tires, I blew the trans up replaced it with a $200 manual valve body th350 blew that up and dropped a tci street fighter with a converter with 1800 or 2500 rpm stall and it would flat out destroy the rear tires with all the transmissions tho, I dropped a nice little 325ish hp 355 in it with a crane Saturday night special had 106lsa cam and a nasty idle and then a lunati bracket master II cam and both sounded sweet but the lunati was way better on the street than the crane circle track style cam and obviously it was bit faster but for the buck it was just as fun with the old tired 350. I miss that car shoulda kept it it had the usual 70s style setup, shackles and air shocks stripes on the hood, 14x8 aluminum slots mags 235/60s on back and 14x6 unilug slots on front with a 195 or 205s or something, but those unilugs were it's demise one day the front right wheel sheared the lugs and took off but it porked the fender on its way out i got discouraged and sold it after i pulled the motor n trans, it was pretty rusty too, i vowed to never run uni lug wheels again.

@Gojira5667 10 ай бұрын

I work alone in my shop. Never had a desire to punch someone else's time clock. However, it would be nice to have someone like you to work with.

@colin1567 7 ай бұрын

Probably one of the more wholesome comments I’ve seen a while I bet you’re shop would be awesome to work at

@AR-nu4qe 6 ай бұрын

You have ur won shop? How did u do it

@TwLilBubba 3 ай бұрын

🙌

@keglock54 Ай бұрын

I wish I had somebody to work on cars with to learn well motors

@TwLilBubba Ай бұрын

@@keglock54 Mann we all do

@chetstarvish2859 6 ай бұрын

I’m 55 and props to you young man for your thorough knowledge of engines across all brands you should be damn proud of yourself.

@Harrypotter-og3bl 4 ай бұрын

Much respect my brother

@redneckswitwheels Ай бұрын

All he does is repeats someone's posted info he don't know sh it

@briang4470 Жыл бұрын

Good results from a 350 can be done ALOT CHEAPER than what is listed here, find a 86-02 880 casting 1pc rear seal short block, find a set of vortec 350 heads(heads used form 96-98 trucks and 96-02 Vans) port the heads a bit yourself and then if you have a bit to spend, send the heads to the machine shop and get them milled down a bit and maybe even a 3 angle valve job if budget allows, then get a thin shim style head gasket and get a carb intake for the vortec heads, get a cam with around .480-.500 lift, for an N/A build MSD ignition isn't necessary just a stock type HEI distributor is more than enough, and for carburetor use any good carb in the 650-750cfm range, it can be a Holley, edelbrock, or even a good quadrajet, all of those will do the job. And bam, you now have solid reliable set up that will make a solid 360-400hp for under $2,000. And if your on a super, super tight budget just find a complete 96-02 vortec 350 and put a carb intake and hei distributor in it with a set of headers and it will make 300hp without changing any of the internals and will bolt right in place of any older type 350.

@1DS9 Жыл бұрын

Lmaooooo

@Christoph_NTX Жыл бұрын

Verified solid budget build

@Christoph_NTX Жыл бұрын

Locked timing

@briang4470 Жыл бұрын

@@Christoph_NTX locked timing can make it hard to start unless your running an MSD box with the start retard feature. But just limiting the mechanical advance or just running lighter distributor weight springs helps.

@irocz1380 Жыл бұрын

I’ve done this 😂😂😂 but I also shaved the block down it’s is a monster set up

@cloudyam2286 Ай бұрын

Replacing my 90hp 2.5 in my 90s Dakota on airbags with a 1970s 350 and 4spd trans. I picked this motor for the pure simplicity of it. I’ve never motor swapped anything but if she got fuel,air,spark she’ll run

@MatthewTitterington-bq7eh 10 ай бұрын

I'm learning so much about V8 from your videos.

@BurlSigler 10 ай бұрын

Man, you don't need non of that stuff. Money is tight! keep it original that's the way to go!👍

@troyburns6971 10 ай бұрын

Went from mild to wild quick 🤔 , don't forget about a high speed stall converter for that thumper cam 😂😂🔥🔥👍✌️✈️✈️

@MultiKelly85 Жыл бұрын

See, this guy gets it! The real deal king of motors! Small block 350! Do like he said and when you put it all together, you'll make some fuckin magic!

@keiths.4540 2 жыл бұрын

I'm saving this video. Got a 85 monte carlo I just put a 350 in. Need it to move when I want.

@bobduncan9840 Жыл бұрын

Will you be making videos. Be interested to see that

@jordieclaudio1449 Жыл бұрын

Bro I just inherited my dads Monte Carlo ls has a 350 in it as well haha

@keiths.4540 Жыл бұрын

@Jordie Claudio lol wow nice. I got mine from My father as well.

@danieldowd8205 Жыл бұрын

Keith there's waaayyyyy cheaper ways to do what he's saying in the video. He has the right idea, but one could do it much cheaper. Not a bad video but that's an expensive parts list that he's just shown.

@validpoints8186 Жыл бұрын

85 Grand Prix ... GBODY

@user-nk6nj7kw6b Жыл бұрын

This gentleman is one of those guys who is great with sharing information that some mechanics won't share due to charging for something too expensive. "Electric water pump." Excellent idea!

@Exquisitewrk Жыл бұрын

It’s a response of a magazine dreamer..not a builder..yeah throw a 1200$ water pump On it..that’s half the build cost 😂

@josejuanrosales3614 Жыл бұрын

Love the simplicity of an old sbc 350

@Texasmule 7 ай бұрын

Tuned by a flat head and a 9/16 wrench(for the distributor)

@Stainlessslayer 11 ай бұрын

I went 385c.i. 10.7:1 compression. AFR 210s, 240/244. .575/.590 on a 107 lsa. Victor jr. Manifold ported Courtesy of wilson manifolds. Sniper efi. Spent 4 years getting the parts. Who needs budget when you have patience

@jamespepper2541 Жыл бұрын

I got a 350 4 bolt main and it's bored 30 over. I have a comp cam 292h cam with world product heads they have been ported and polished also milled with double springs. My heads are good for 570 lift with 58 cc chambers. I want to run an air gap intake with a 750 carb also, I'm running flat top Pistons. I'm hoping for 450 horsepower. 😎

@cegill23 9 ай бұрын

What about the pistions?

@jamespepper2541 9 ай бұрын

@@cegill23 I thought, I had it my engine machine guy screwed me over!!!

@kdsboosted4954 4 ай бұрын

@@jamespepper2541Screwed you over how?

@jamespepper2541 4 ай бұрын

@@kdsboosted4954 Mostly by wasting my time almost a year of my life waiting on my engine machine guy giving me the run around.

@lastfanstanding999 Жыл бұрын

Long tube headers and duel electric fans, oil cooler, purhaps electric fuel pump as an option ! Short videos are limited so I'm just helping. 😊

@gbeving3167 10 ай бұрын

I've had too many issues with electric pumps, just run a decent mech pump

@atomicaddict111 8 ай бұрын

no need to run an electric pump for a carbed setup. the mechanical pump with be more than suffice

@gbeving3167 8 ай бұрын

@atomicaddict111 technically less loss I guess, but I run a mech pump myself

@carolriley9392 10 ай бұрын

Always the best information, no nonsense channel!

@blazecarnie4721 Жыл бұрын

Gotta do this with the 305 in my 86 c10, but she sounds so good open headers as she is right now..

@Drew_peaballs_128 11 күн бұрын

Nice SBC with a 100/150 shot for racing other than that street cruise Sound alike a good idea

@Aidanthebigman 3 ай бұрын

Nice stuff! That build is a little on the wild side I’d say!! But it would do! And would need a high stall for auto trans! Good build! Mine is 185cc int. Pro max project x heads, stage 3 LS firing order summit 1223 cam, dual plane rpm air gap intake, 750 cfm Holley vacuum secondary. More of a low end grunter than a high revving hp beast.

@JeffRogosz-zh1zo Жыл бұрын

My favorite chevy motor vortec heads carbed intake and a LT4 hot cam

@GiancarloFloyd Жыл бұрын

I have this exact same set up minus the water pump. I hate electric water pumps in my El Camino. It’s not fast or anything compared to my LS cars but it does make me smile and that’s all I needed to do. It breaks the tires loose it will get Squirrley in the car plus brand new engine costed me under 10k

@rashewhite Жыл бұрын

You warmth a 600 to 650cfm carburetor for driver ability. 750cfm for drag race and lots of nitrous.

@docsmallblock6584 9 ай бұрын

The regular ol hei ignition is plenty good enough for that! No need for an msd box , actually I've ran the GM hei ignitions @ 500hp with no issues. The Chevy 350 is an awesome engine that'll take one hell of a beating!

@kaseykiller7973 6 ай бұрын

Okay here is one for you I've always been just a part's changer. Alternator goes out. Put a new one in belt goes out. Put another one in transmission goes out. Put another one in never pulled a motor never really did any type of upgrades to anything. I got a 1978 Chevy long bed. It's got a 454 in it it's a big block. Small block. Not quite sure on the transmission I know it had a 203 transfer case which blew up. It's sitting on 46 inch. Tires with the 13 inch left with the 4 inch body left. I have way too many questions to ask. I've been asking the same question to a lot of people on KZfaq. How do I find out what type of 454? It's got what type of transmission. It's got what would be the best set up for 44. The transmission and transfer case too many questions to ask. Not enough people out there answering. I'm 44 now. I'd like to have it somewhat done by a time on 50.

@santannathegreat5167 Жыл бұрын

You hella intelligent about automobiles my guy!! I just subscribed, I dig your energy my guy

@markharris1473 Жыл бұрын

I like this dude, I subbed to your channel. He makes good sense when he said looking for a cruiser in your C10. Yes that is a nice cruiser engine. I mean you could go a size or 2 bigger on the cam, but you're looking at changing the pistons to a higher compression which means using a higher octane fuel. But from 360 to 400 hp is a lot for the everyday driver. Also gear change, transmission kit for harder shifts. Only if you wanna go bigger. But this man knows what he's talking about. And he's right about the everyday street cruiser. 360 to 390 hp is plenty hp. I give him my 2 thumbs up, 👍👍😃

@yashuwasaves Жыл бұрын

Same motor i have in my c1500 chevy love it

@tyroneharrison84 Жыл бұрын

Great video bro. Keep it up. Don't let the internet master mechanics tell you different.

@Bobthebuilder.69 7 ай бұрын

I just dynoed a l31 carb'd vortec with a Comp cams 4x4 cam and decent port job. Made 371hp and 409 ft lbs of torque. Runs like a scalded dog compared to stock

@gregoryfrink8931 3 ай бұрын

Keep it coming us car guys appreciate your knowledge..

@jacobdimarco4204 Жыл бұрын

Deck the block and get a set of used vortec heads and change springs and retainers to handle .520 lift and throw in a good cam and lifters with a speed master or another cheap intake with a 650-750 cfm carb and a msd distributor will get you to 400hp and possibly more

@zachnickles7655 Жыл бұрын

All stock bottom end Vortecs 480/480 hurricane intake and 750 makes 435 z28 springs stock distributor Inch and 5/8 headers This is at the crank

@patrioticaussiesams8581 18 күн бұрын

Still put a 383 Striker kit into that package will give more torque. It doesn't cost heaps more WELL worth the extra Coin

@lm5085 10 ай бұрын

Combine that with the correct intake and some mild work on the heads and back cut them valves. I built a similar beast 30 years ago. I used 2252AF TRW powerforged pistons. Damn that was a beast

@D.N.Collins 3 ай бұрын

You know your stuff. Keep on making these videos. 🔥

@diegoabreu9608 4 ай бұрын

Saving everything from this video gonna do this same exact build. Please give me somewhere i can send you pics of updates.

@jimmychandler3760 Жыл бұрын

Great video keep up the great work you're doing

@caseyaylward8853 Жыл бұрын

Thanks dude. You literally answered the exact question I was asking. I have a sweet 87 K5 Blazer but it's really slow. The motor is fine it's just slow. Ima do exactly what you just said.

@samhapke6862 Жыл бұрын

You can do it for way cheaper and make the same power

@caseyaylward8853 Жыл бұрын

@@samhapke6862 how?

@samhapke6862 Жыл бұрын

Vortec heads - $100 on marketplace Mill heads .030 and valve job- maybe $400 Valve springs- $60 Cam and lifters- around $200 Steel shim head gasket- $20 Hei distributor- $70 Aluminum intake- ~ $100 on Marketplace 650-750 cfm carb- $300 or so (depends if you rebuild a carb or are buying a new one) I’m assuming you already have a good 350, and front accessories. You may already have an Hei distributor. So all in all it might just be a top end swap for you. You can def make high 300s hp with this recipe. Maybe 400 if you hand port the heads a bit. If you hunt for good deals and negotiate you could probably have it all for under $1000 versus the near $4,000 you would spend for the video combo if you include taxes and shipping. Richard Holdner has a good video on a budget Vortec build on KZfaq.

@samhapke6862 Жыл бұрын

@@caseyaylward8853 or you can sub the used Vortec heads for a new casting from Scoggin-Dickey or JEGS/Summit ,some cheap aluminum heads, eBay or used ones from marketplace

@Camopar87 10 ай бұрын

I have a 74 C20 with a 350. When it needs rebuilt I'm going to turn it into a 383 stroker. I'm going to kept it looking factory so it'll be a sleeper

@2414kels Жыл бұрын

I had a Chevy 350 brand new block thats been sitting for years. My neighbor build engines, so i had build my 350 was able to squeeze 420hp out of it. I put in my roller 89 Camaro. Its in paint shop now candy cobalt blue then going for suspension and handling upgrades.

@kyleanderson6505 3 ай бұрын

Great list although I’d go for a different cam. The motherthumper is more for noise than actual power/efficiency. Also, a good set of vortec heads from a retailer like Scoggin Dickey is a great option or AFR Enforcer 195s if you want aluminum heads

@SweatyFatGuy Жыл бұрын

That is a lot of money to put an anemic 350 in something. I bought a rusted and parted out 2500HD pickup for $1000 with a good 6.0 and 4L80E in it. Needed the rear end for my 2500 I use to haul things in winter, so I figure the engine and transmission are free. Swap mounts are $150 if you get the pricey ones, but you can use stock sbc mounts if you drill a hole in them. Use the fuel tank from the donor truck, and run nylon fuel lines to the rails. Its simple and easy. You can use the radiator and lots of other stuff from the donor truck. My 76 C10 and the 80 C10 along with the 88 C1500 are all getting 6.0 low buck swaps... because $400 buys a rusted out 4x4 with 150k on it where I live. It helps I can rebuild transmissions, engines, and everything else, but this is doable. For all my cars, well they get Pontiac power because 450ftlbs is super easy, and 550ftlbs is just a 4.25" crank kit away with a 400 block or with a stock bottom end very mild 455. $2500 spent on a 455 gets 11s in most muscle cars, and its mostly factory stuff. Iron heads, cheap headers, stock intakes work just as good as aftermarket ones, whatever compression ratio you want is attainable with a head swap since they all have flat top pistons and every head from 1954 to 1979 will bolt to all the blocks made during that time. Then I can tell everyone that that 505 in my car is just a 326... I dig sleepers.

@ryurc3033 Жыл бұрын

.30 over 4 bolt main block, forged flat tops, used forged scat crank stock true vortec head( not the fast burn 89 truck crap).big cam, headers. 350 ish hp and reliable

@ryurc3033 3 ай бұрын

O and never ever an electric water pump on a street motor.... never

@hamletxxx1363 Ай бұрын

That's 450hp right there. I just did that last week in a 1982 El Camino

@doobzthechamp3134 6 ай бұрын

MAN KNOWS HIS SHIT. I CAN LISTEN TO CAR GUYS TALK CAR SHIT ALL DAY

@sylvia8583 Жыл бұрын

Stroke it a little and a top end kit 355 good enough or big power 383 easy 500 HP

@sylvia8583 Жыл бұрын

Now this is true this guy has fuckin style brother you should make a video of this set up

@yonatantesfay5541 4 ай бұрын

Im a big fan, thank you for giving me hope. I just want a small block with a nice lope.

@MystikalDawn 7 ай бұрын

Just finished dropping my brand new crate SP350/357 in my 85 TA, paired it up to a TH350 with a 3000RPM stall, should be fun this summer.

@MuscleWagonRT_T.V.9143 7 ай бұрын

Ok so I did almost everything he is talking about. No electric water pump. But a rpm performer intake and heads, 750 double pumper, msd 6A with matching distributor. Long tube headers and a 526 cam. It made almost 600 horse with a 1000 horse turbo 400 tranny. Don't use a turbo 350 on your 350 engine the 400 can handle more power easily.

@chehystpewpur4754 8 ай бұрын

you want a good sbc. vortec 5.7l fuel injected turn key like a daily driver. cam and headers is over 400hp. torque off rip. for 1200 bux you can rebuild a vortec 5.7 stick a cam in it. the one i picked is perfect for the application. and get the headers u need for ur car but it loves long tubes.

@MystikalDawn 9 ай бұрын

I went out and bought an SP350/357 and a TH350 and heaved that into my 85 Trans Am, should be half sick when it's done.

@davidwasicek9869 Ай бұрын

Love the channel

@Smokey-88 3 ай бұрын

350ci plus compression 11.1 will do wonders, get some camel humps 2.02 and MSD = 425+ hp Combine that with a solid TH350 and you can neutral drop it all day long.

@ramie-uz9xi 6 ай бұрын

Save yourself some money . Use that Delco distributor with an Accel super coil and cap . All the spark you need

@RockstarMafiaa Жыл бұрын

It’s funny as hell cause I started off with this set up now I’m too far gone

@gmonjr2079 Жыл бұрын

Is it a good setup

@RockstarMafiaa 6 ай бұрын

Damn right . Great start off . Especially easy for someone that's just getting into building engines . I have the same motor twin turbo'd , forged flat pistons and same vortex heads ported and polished about 8 psi boost yessirr I haven't dynod and he also hit a big point . GET THE MSD TIMING IS EVERYTHING WITH THESE MOTORS

@Pendragon69608 6 ай бұрын

Speak the truth brother I have this motor and pulls hard and I just want to give it more spice to it and I think this is what I will do

@Allmotorjun Жыл бұрын

Love the old 1st gen 350 in a s10

@connormcnamara6490 11 ай бұрын

thats what im fixing to do. how hard is it to get the engine mounted.

@willy3sticks647 10 ай бұрын

@@connormcnamara6490 Not hard at all ive built 7 V8 S10's the fire wall needs to be clearanced for the distributer, and the stock drive shaft will usually work on th350 tranny,if you can mount the motor back far enough

@jaws2003 7 ай бұрын

This is a solid setup

@memynamealex3514 Жыл бұрын

Got a sbc in my 84 cutlass and I love it😂

@xenissus8551 Жыл бұрын

Got a sbc in my 84 grand prix🤣 I love it too

@wxxregta8388 Жыл бұрын

Same I got a 390 in mine

@Sinsirink 10 ай бұрын

4 door or 2 door

@memynamealex3514 10 ай бұрын

@@Sinsirink2 door

@ZootedSosa Жыл бұрын

This is exactly what I’m looking for I want good power but I don’t wanna constantly replace shit just a good little street truck

@SOLDOZER Жыл бұрын

Just get a stock Vortec engine.

@Sluggger69 Ай бұрын

@@SOLDOZERno fun or conversation in putting in a stock engine, it’s always more fun to actually actually tinker with it and make it how you want it and it gives a good conversation topic to people wondering what all you did to your car, putting a bone stock engine in a vehicle takes the fun out of it, also it’s always fun once you build it to how you want it and take it to dyno to see how much power you can get from your build.

@SOLDOZER Ай бұрын

@@Sluggger69 Plenty of fun in a stock engine. It will come with a warranty.

@Sluggger69 Ай бұрын

@@SOLDOZER warranty doesn’t matter if ya know how to build an engine and fix it yourself and warranties are limited they don’t last forever, also the moment you try to modify that engine to get more power your warranty goes out the window

@morbidchaos254tx4 3 ай бұрын

Dont forget, certain honda connecting rods are the same spec as 350 sbc rods.... good way to shed some rotating mass

@nickholzschuher1421 Жыл бұрын

You can make around 400 horsepower out of a 350 by born at 40 over putting bowtie heads on it and a 305 Crank That Way has more RPMs with a 4-barrel elderbrock 750 CFM carb cuz if I can get 550 horsepower all motor reliable out of a 305 you can definitely do it with 350

@off-roadmechanic 3 ай бұрын

I have to keep this all in mind have a 85 Firebird trans am with a 350 cop engine in want to try and push more power out of it Edit we started tearing down the engine and I checked the casting numbers and it’s a 305 gonna be a lot harder to push any power at of that thing Another edit :ended up buying a 350 small block so when I do get the chance one day I’m gongs to try to push a good bit of power out of that sucker

@doctorwhodj Жыл бұрын

The mother thumper is for a street rod where u dnt care about low end torque n idle quality. A truck needs good low end n idle

@elcaminodraco Жыл бұрын

That added up quickly 🤒🤕

@matteblackexterior Жыл бұрын

you can do it for cheaper, I built an average Joe 350 and it’s got a small comp cam in it and overall I would say it makes about 180 horsepower but it’s probably got 300 pound feet of torque and the only major difference is that I have an edelbrock torker intake with a Holley 600 and cam and it’s not even 800, you can build a high compression 355 that pumps maybe about 350+ horsepower for $1575 with a lunati voodoo cam, KB high compression pistons, oversized valves in a pair of stock heads, edelbrock performer intake and a Holley 670 street brawler carburetor and a high volume oil pump (which may not even be needed) I think this guy is just talking from a perspective of money isn’t an issue

@Ab-glo 6 ай бұрын

@@matteblackexteriorbest comment

@P-nutBD 11 ай бұрын

I'd take a 4-bolt main block bored 30 over. KEEP the stock 350 crank and build the bottom end for a 355 build. Then find 202-iron heads and match that for a 1.6 lift on those rockers, pait that with a 12-deg RV cam. Use an Edelbrock performer intake and mate that with a 750-800 cfm crab (or a jetted out quadra-jet carb would do). Ignition is probably the MSD otherwise a modified-from-stock HEI would do. High volume oil pump and high flow fuel pump. My dad built this with a buddy and had 550ish BHP at the crank 490-505 at the wheels in a 76 k20 paired to a th350 and np203 transfer on floating axles. It was bonkers. mechanical water pump though: I personally wouldnt trust an electric pump.

@BigCountry_06 22 күн бұрын

Might have to take notes I need to rebuild the 350 in my 85 blazer 😂

@hessdominguez170 2 ай бұрын

Love the old school build po did in my k10 nice power all across the board and it’ll spin and keep it all 4 spinning if I want 😂❤

@rivernorcal679 Жыл бұрын

Love the Life you Live!

@williamromero4445 Жыл бұрын

This set up actually can get you 405 HP 👍

@henrywal Жыл бұрын

Great car spokesman no doubt.

@KevinMartinez-nh7qx 11 ай бұрын

This the comment i was looking for lol thanks

@WilshIAm 11 ай бұрын

yeah this setup is good for way more than 360hp you can get that easy with a stock engine and a 100 shot of nitrous

@enriqueharris9702 2 ай бұрын

If i do this for a truck, how much torque are we talking about?

@punishersantiago 11 ай бұрын

Perfect set up for my OBS GMC 🤙🏾

@lancegodbey6450 11 ай бұрын

Dad's got a 85 k15 with 33s and the old manual fuel pump. I feel it would be way more cost friendly to block it off and go electric, already got the electric water pump. Just my two scents, but it does need more power

@dewaynem559 8 ай бұрын

You can have your LS enguine the last 350 I owned I got over 400k miles out of it and it was still running great when I sold it

@bradthackston5217 3 ай бұрын

Crazy how a mild build on an old engine is less then a new truck stock the 3rd gen coyote is 400 hp 410 lb-ft technology is crazy

@princetyler9886 Жыл бұрын

Got one in my 72 cj5 man that thing is fun to drive 💯

@Joehouse900 10 ай бұрын

Why are you speaking directly to me

@1949joshuarodriguez 13 күн бұрын

With that kit that he's explaining, you might as well buy A. L. S3. Back in the days building a bad ass 350 was cheaper to me. It's not worth it. The field injected motors nowadays are way better.

@robertblah2373 Жыл бұрын

Cheapest option is 993 heads(not crack prone and flow just enough in stock form with 1.94-2.02 heads) Used dual plane intake of your choice Flat top(regular gas) or pop up/dome(premium gas) pistons L79 327/350hp cam from melling Z28 valve springs 1.6 stamped rockers if you want just a little extra power(prefer stamped because they're cheap and essentially never fail) Cloyes or similar adjustable timing kit set to advance the cam to bring down the l79 power band to be more low rpm and street friendly 160 degree stant superstat This will get you into the 350hp ramge with a dummy amount of torque and is gonna be the cheapest while still reliable option. I'd bet if i built this and somebody built the engine he suggested,i could walk away from their pile of missmatched thrown together parts down the strip if both cars were equal. Especially a heavier street car Almost forgot,no fancy ignition. A stock HEI will work,or an accel/msd HEI will work better. No need for anything more at the rpms these kinda engines will see

@phatgav1923 2 ай бұрын

My 88 Sierra is about to get these mods thank you for the help lol

@allwork_noplay 4 ай бұрын

Yessir 💪🏾 aye bruh on his shit, he be taking kats to school wit it, Salute cuz

@mrwelch5517 Жыл бұрын

I know it’s probably irrelevant to a lot of people but maybe do a overview on the GM 3800 V6 naturally aspirated and supercharged

@majorkeys616 Жыл бұрын

Plz

@free4gs 11 ай бұрын

me personally i wouldnt do an electric water pump or an msd ignition. i prefer an HEI ignition.... but its all about how you want to build you car/truck, i like small blocks/big blocks for the lack of electronics

@HairBandDan Жыл бұрын

I like your idea, but ever since I got a Big Block it’s hard to Go Back tho

@user-ro1lt1px5j Жыл бұрын

Really enjoying your videos bra

@rydahj5054 2 жыл бұрын

Thanks mane I got a sbc 350 in my 71 Monte Carlo now I know what to do

@lattojynx5684 2 жыл бұрын

Same 84 Mc ls

@sylvia8583 Жыл бұрын

Stroke it

@davidgomez3737 6 ай бұрын

You could make probably the same power if you piece everything together separately and in the long run you save yourself money for example that ignition system itself would probably run around 800 $

@Daveyboy919 9 ай бұрын

I had a 74 Camaro with a 350 with headers. That had so much power it was scary if I power braked it the tires would dig into the street 3inches

@nouns7504 5 ай бұрын

Saving this, was gonna do a ls swap for my 1989, but its 2wd i think a 350 is fine for her now

@kongzfitnesss3892 8 ай бұрын

lol you giving some crazy combos that ain’t cheap

@mikekerr4594 10 ай бұрын

I'm doing that. Cool!

@Ted_Dee 10 ай бұрын

Good engine

@bizzyb8 7 ай бұрын

I like this guy

@doctorwhodj Жыл бұрын

220cc heads are for 450-500 + hp wild street build, u need 170-200 cc,,, the cam you picked is for 2500-6500rpm... a mild 350 needs a cam 1200-6000rpm cam. Electric water pump os a waste of money the mechanical won't take away much in a low rpm mild,, don't need mad box for mold just a good hei set to hood timing, 32-36 degrees

@aaronjonwanyemcnair8629 11 ай бұрын

My guy. Love it

@lamarchevelle8639 4 ай бұрын

Thanks bro🏆🏆🏆

@Unit957 Ай бұрын

😮... I've seen that before..even that fuel pump ..

@kinglokimrvegas8687 3 ай бұрын

Man some of those built 350s fly i had a 03 suburban that had a 350 and it was nice because it was fast but not as killer on gas as a big block and have seen some built in square bidy trucks and s 10s that can outrun some newer cars with ease