How to Bypass O2 Sensor

No video

How to Bypass O2 Sensor

Рет қаралды 76,047

Auto Hacker

Күн бұрын

#foryou #o2sensor #oxygensensor

Пікірлер: 53

@577buttfan Жыл бұрын

For all wanting to find out what wire is the signal ground you need to start up the car and look for voltage between it and the positive side of battery.

@ronaldhamblin4615 7 ай бұрын

This is verry halpfull to me menny thanks to you keep them vidios going kind regards to you

@FENIX-re9tx Жыл бұрын

La resistencia puede ser ser de 1M ohm 1/2 watt, y el capacitor de 1uf 50v segun entiendo (no se porque pero en unos paises cambia el color de la resistencia 😢)

@plusblood5101 Жыл бұрын

Zabardast dost

@RoadHeros610 9 ай бұрын

Very good video ...when you d0 this bypass do you ever get a heater code for high circuit on heater when your heatwr circuit is good

@RoadHeros610 2 ай бұрын

@@Lrv6532 I sold the bucket Lexus .. I've had 2 Japanese cars both hat cat and or 02 issues .. think I'll keep to my German cars ..

@jupitermobile6984 5 ай бұрын

Hi, can I use this method for my van? My van is showing engine light and it is saying sensor is not good.

@chiathau Жыл бұрын

How to know the proper ohm to use for the O2 sensor? anyway to check that? thx

@pornokid333 Жыл бұрын

Also to add, if you shake the sensor close to your ear, and you can hear a rattle...the element inside is burnt..no need to test.

@hpat225 Жыл бұрын

Please Can you right the exact value of the resistor and the capacitor ? Thank you a lot for your video.

@autohacker1137 Жыл бұрын

1 oham

@hpat225 Жыл бұрын

@@autohacker1137 you said 4,84 Kohm in the vidéo.

@autohacker1137 Жыл бұрын

That was an example, please listen to audio, i have said that use 1 ohm

@hpat225 Жыл бұрын

@@autohacker1137 Ok. 👍

@m1r786 Жыл бұрын

Thank you, much appreciated your video ❤️.

@century21z 10 ай бұрын

Hi, You used, 1Momhs 1/4 w and the 1uf 5 V or 50v.

@luiscuenca7926 10 ай бұрын

2005 Jeep Wrangler 4.0 all 4 sensors testing low on heater code P0031 - P0037-p0051-p0057 I replaced all with NGK and still lit on. I checked all the wires, disconnected the PCM, and continuity was all good, Pin 1-3-4 were good from the sensor to PCM plug and pin 2 to ground, what else?? Thank youi

@autohacker1137 10 ай бұрын

Either the sensor itself is bad or the harness is not gripping well. H2OS code p0031 is related to heater cicuit reading low, check the pins or the wires

@autohacker1137 10 ай бұрын

If the harness, the pins, wires have been checked and are ok, or if you have replaced the sensors with new ones, i will suggest you to recheck the continuity of the sensors, not matching the desired or required by the ecm

@jeremygugelmeyer4586 Жыл бұрын

Are all o2 sensors the same resistance

@Firefrei 10 ай бұрын

would this work for a p0137(low voltage from rear o2)? the sensor is the correct one and good but since i installed headers its been setting it as a nuisance code

@jimholland7622 Жыл бұрын

So if someone cut my cat's out I'm in a state where I don't need them to register the car so if we do this we don't need the downstream sensor at all do we?

@GenesisRC Жыл бұрын

You can leave it but the ECM will be mad and the money light will stay on

@roskomon1 Жыл бұрын

And us there away go get read off the light

@djdonbentley2141 9 ай бұрын

if you live specifically in the northeastern states, they are trained to spot devices attached to the vehicle such as these. they know what they are doing and will fail you . i hate the northeast , over here , you will 100 percent fail emissions just for a check engine light on, even if its not related to emissions. just the light being on will be a fail.

@jaywaves6575 9 ай бұрын

can I do both just to get rid the check engine after catalytic converter delete?

@joelock7691 Жыл бұрын

The blue color is a signal rite & white is a eart?

@Alientraveler003 Жыл бұрын

👏👏👏😛😛👍👍

@chidiuche754 Жыл бұрын

Can it work for upstream oxygen sensor?

@autohacker1137 Жыл бұрын

02. Only

@chidiuche754 Жыл бұрын

@@autohacker1137 Is it the first sensor or the second sensor?

@chidiuche754 Жыл бұрын

Or both?

@autohacker1137 Жыл бұрын

Second

@gallantfox4776 2 ай бұрын

It’s give me po606 ecu code what should I do

@Hamid-az Жыл бұрын

Actually heater wires don't make sound when you test it by multimeter and 2 wires have the resistance between 3-10 ohm.

@nek123 11 ай бұрын

Bravo - you outsmart the sensor, the control unit recognizes it as OK. It just can't regulate it, your ECU always gets the same input. As a result, the car never runs properly. BUT - you will no longer receive an error message!! Your crafting is total nonsense!

@autohacker1137 11 ай бұрын

I think i have mentioned that in the video, kindly no need to be over smart here. Thanks Mr, perfect

@dramjadali756 Жыл бұрын

السلام علیکم ۔۔۔برادر میرے پاس move 2015 dihatsu ہے۔RPM 400 سے اوپر نہی جا رہی اس پہ ہینگ ہو جاتا ہے۔چیک لایٹ شو ہو رہی ہے اور P0420 کوڈ دے رہا ہے۔میلیج کم ہو گئی ہے پٹرول زیادہ یوز کر رہا ہے۔catalytic چینج کی ہے کابلی لگایا ہے۔میر ے والے کا مٹی ٹوٹ گیا تھا۔آپ کچھ مشورہ دے سکتے ہو۔٢ مکینک کو دکھایا ہے لیکن تسلی بخش جواب نہ ملا

@autohacker1137 Жыл бұрын

Neechay walay oxygen senor mein adopter lagwa lo aur computer reset karwao set ho jaegi, P0420 catalytic aur o2 sensors related issue hai.