Decrease-Start does not work on my charger. Is the calibrate menu not available at all for some firmware versions? If so, I'll load new firmware.
@boeingpete8 жыл бұрын
Useful to know. I tend to use another branded battery checker after using my B6, and it is always a little on the low side (i.e. the safe side).That said the B6 does do a pretty good job of balancing the cells with a max diff of 0.02 volts which I can live with.
@Erik740t2 жыл бұрын
Yes, I have another now, still low.
@cakonemicke21988 жыл бұрын
a clone imax. You should add it to description. Nice helpful video
@ItsMeJbird8 жыл бұрын
good video!
@Spartacusse9 жыл бұрын
I, myself, rather it undercharge. Mine is also a knock off and I know they don't read voltage very well, so I rather it thinks it's 4.2 per cell when it's actually 4.15 than the other way around. Besides the reduced risk of lipo fire, undercharge will also increase battery life.
@CrazyCruz269 жыл бұрын
Hey what If I can't get into the menu while holding down the keys nothing happens?
@paulkaygmailcom9 жыл бұрын
problem is that calibration doesn't account for individual cell imbalance.. you need to either charge each cell separately to make a very balanced pack OR build a precision resistor voltage divider to calibrate the unit
@paulkaygmailcom9 жыл бұрын
***** are you kidding? voltage per cell is irrelevant? Let me know how your 3s pack does with one cell at 4.5v, another at 3.9 and 4.2.. sure overall voltage it correct for a full pack.
@paulkaygmailcom9 жыл бұрын
***** with the factory firmware and the cheap iMax clones individual cell calibrations are most likely off.. like I said before, if you think that one cell that is overcharged is irrelevant then you my friend lack some basic knowledge in Li-ion/polymer charging safety. IF you only calibrate the over-all voltage detection and increase it from its factory setting you would only be compounding the problem if there is an individual cell reading lower than the rest. That is why I would not recommend showing the world only half of the calibration procedure WITHOUT also calibrating the individual balance ports with a verified pre-balanced pack or a precision resistor voltage divider.
@Erik740t2 жыл бұрын
The charger accounts for individual cells. Calibrated correct, each cell will be correct. Smart-ass, it's science
@santoroma178 жыл бұрын
has anyone had an issue with it booting right into discharge battery mode? i cant fix it..
@jimhill40448 жыл бұрын
Erik740t how did you get it to charge without the balance plug plugged in.
@Erik740t2 жыл бұрын
You can charge, without balance
@zhillsx9 жыл бұрын
Very helpful info thanks. I just bought a Dynamite Prophet Precept charger. When I balance charge the charge will stop at 96% actual full but reads at 100% full. I went to use your calibrate method and found the charger to be correct in the voltage reading. So after balance charging a battery I have to put it in charge mode to top off at your suggested .2 amps and works fine at 99% full. Is this a common with lipo chargers to work this way?
@randy12033 жыл бұрын
I see a lot of confusion here, would you mind moving the camera closer in, to then better see the buttons and view the screen? Thanks.
@Erik740t2 жыл бұрын
Wasn't thinking about it at the time. Just doing the best with what I had.
@eduardomalcom22289 ай бұрын
Hello, is the calibration done only once ? Or is it done with every battery that is going to be charged? Thanks
@Erik740t9 ай бұрын
Only once
@josemanuelburgospolanco14177 жыл бұрын
Good video? Not working in imax b6 mini?...
@chris551302 жыл бұрын
I got a real Sky RC IMax B6 and you can't calibrate it I tried but it's not necessary. It's spot on when compared to a calibrated Fluke meter.
@Erik740t2 жыл бұрын
A real one would be ideal.
@NickDelDuca9 жыл бұрын
What meter are you using?
@ca11910 жыл бұрын
calibrating .... can you do it several times, or just once? (read it was only posibile to do it one only time?)
@Bullshitvol210 жыл бұрын
As far as I read you can do the balancing calibrating just once. I can do this single calibration as much as I want. Erika Thornes thanks for that tutorial. My Imax still gives me to high readings (+0.06V over Norm) but at leasts its better than the +0.18V earlier. Now it charges an Lipo at least to 95% max capacity (earlier it was around 80%)
@Erik740t2 жыл бұрын
Unfortunately just once
@Andre_M_3D6 жыл бұрын
I tried it with the clone B6 mini and no luck. It was a cheap 20$ charger so I got it as my ISDT Q6 plus will only balance charge and the battery for my QX7 cannot be balance charged so I figured why not. I knew in advance this would probably not charge correctly as they are not calibrated very well from the factory. Hopefully, someone will know how to do this
@UlisesBatalla8 жыл бұрын
When I press the two buttons this menu will not come up?
@miguels1888 жыл бұрын
i have the same problem
@maxdj81666 жыл бұрын
same sh.... Remember, yet, on a previous fake B6, having done this w/o problem... Any chance you found the solution by now?
@Shadow_of_STLKR7 жыл бұрын
For Dec and enter Shows: System update Please Wait... ? But its in ACv2
@Microplastic_Therapy3 жыл бұрын
I bought the same charger and it was way out of whack, now it’s calibrated
@markward41767 жыл бұрын
anyone know if you can make the screen brighter on this charger?
@MariusVilceanu4 жыл бұрын
This is not original skyrc mini
@bartsshorts4 жыл бұрын
my imax b6ac is showing wrong voltage of the cells, i know my 6 cells are 3.8v but the charger is charging saying they are all over the place, 4.11v etc. damn.
@Erik740t2 жыл бұрын
I will remake this video but zoomed in and enhanced within a week. I am sorry about the visuals on this.
@mafiafpv34694 жыл бұрын
You have to do this to every battery???
@Erik740t2 жыл бұрын
No, just one time when you know it is correct
@furulevi9 жыл бұрын
nice camera position! :)
@devinduncan69229 жыл бұрын
furulevi sarcasm I hope... the camera is so far away you can't see what is on the display.
@furulevi9 жыл бұрын
Devin Duncan the position is good, but the distance is not so good...
@Erik740t2 жыл бұрын
I will download this and redo it
@jeffbarton8318 жыл бұрын
ya i just ordered this and from what ive heard on the fake ones it can lock the charger up turning it into a paper weight so i WONT be attempting. If it charges a little under then thats better than over so oh well
@TheKetsa7 жыл бұрын
people just need to know how to finish the calibration procedure...
@ABDUL177647 жыл бұрын
tq
@maxdj81666 жыл бұрын
thx However, I used this menu a year ago on another B6 (fake), and on the current one, this won't show up... No way to get this option. any idea ? (if this channel is still fed and messages read !)
@Erik740t2 жыл бұрын
I am not sure really. It's been a while but I am back.
@jimmihenry2 жыл бұрын
How to calibrate your fake IMAX B6 the genuine one is spot on :).
@Erik740t2 жыл бұрын
Your point? I have a real one next to me right now.
@jimmihenry2 жыл бұрын
@@Erik740t Right one should be on point, no need to calibrate!
@bullrunhunter64898 жыл бұрын
Tried doing what you suggested and it locked my charger up and no longer works. Thanks!
@TheKetsa7 жыл бұрын
What was your problem ? Did you ever find the solution ?
@bullrunhunter64897 жыл бұрын
No i didn't my house burnt down a few days later and it fries so now i use a icharger 406duo. I will never use an imax again for charging lipos. Cheap junk. They don't balance properly or cap off batteries full. You don't realize until you spend money on a quality icharger the night and day difference.
@gymkhanadog7 жыл бұрын
Hitec for life! :D Though I gotta admit, my Turnigy Accucell 6 has served me well for many years. Right now it's doing duty charging and discharging 18650 cells from laptop batteries.
@Erik740t2 жыл бұрын
So, you managed to f your charger up and then on top of that burn your house down? Sounds like total bs, or rival channel, or you need to stay away from electronics.
@cym2473 жыл бұрын
Can’t see the screen of imax charger....charger is far to the camera...
@Erik740t2 жыл бұрын
Sorry, I made this a very long time ago.
@lucasalvatore288 жыл бұрын
My b6ac don't work this MODALITY! WHY===??
@TheKetsa7 жыл бұрын
Some are a bit different, there are so so many copies around. You need to press the "menu" and "stop" buttons on some of them, but BEWARE : search how to calibrate them before or you'll get stuck. you have been warned.
@That99chevy8 жыл бұрын
It won't work for me
@blighto7 жыл бұрын
How can you be confident that the meter you are calibrating to is more accurate than the charger was?
@privateagent6 жыл бұрын
i also need to know that
@mpoerot80135 жыл бұрын
branded pro multimeters
@Erik740t2 жыл бұрын
Thank you, but it has also been calibrated
@mangmukidintea7 ай бұрын
Is not work to my iMax b6ac dual power
@Erik740t6 ай бұрын
Maybe a different version.
@devinduncan69229 жыл бұрын
Huh? You say you entered negative numbers to show the value determined by the meter? WTH?
@tonypinto99524 жыл бұрын
Cannot see the charger display
@Erik740t2 жыл бұрын
Was a long time ago, I apologize
@amalanto17807 жыл бұрын
sir i am having a lipo 14.8v 4600mah 4cell 68wh battery and when i set 14.8v and 4.6amp on the turo charger balance mode and trying to charge to charge the attery the charger is shutting down after 11 sec and restarting.what is the prolem.plss help
@JohnHill-qo3hb5 жыл бұрын
The problem with your calibration process is that you are relying on your multimeter as your "standard". When or has your multimeter ever been calibrated? The number of digits your meter will read is not accuracy, that is resolution, to be accurate, the meter must be calibrated against a standard of known PROVABLE accuracy. I used to work in a calibration shop, all our "standards" were calibrated against the national standard which in turn were calibrated against the world standard. Calibration is a chain, your multimeter is first or anchor link in your calibration chain, therefore the weakest link. Have you considered that your multimeter readings may be in error as well? What I would recommend is that you get your buddies over for pizza, have them all bring their multimeter with them and take a reading on your "standard" battery then average them and use a good stable well regulated variable power supply as your voltage "standard". Then carry on as per your video.
@timyang47754 жыл бұрын
How was the original calibration derived?
@overbuiltautomotive12992 жыл бұрын
really i got 3 units imax 6 and they are like way off and multi-meter ant off that much and were the f is one to fine a hp voltmeter to vett the multimeter he has so we do what we can
@Erik740t2 жыл бұрын
Sorry brother. That meter has been calibrated to the t
@Erik740t2 жыл бұрын
I had the meter in the video calibrated. It is exactly on point.
@Erik740t2 жыл бұрын
Thank you. Even an unclibrated meter is way closer than the image b6.
@onemorehunter9 жыл бұрын
did not work on mine. I dont have the B-6ac. I just jave the regular B-6. Oh, and yes it is the fake.
@That99chevy8 жыл бұрын
Can any one help me??
@emilmadsen89729 жыл бұрын
dammit its not working it just goes straight to lipo charge
@phlopalopagus9 жыл бұрын
Emil Madsen Mine wont go into cali either. Did you get it to work?
@emilmadsen89729 жыл бұрын
Phlop Alopagus no i couldnt get it to work but a few tenths of a percent in voltage doesnt make a huge difference
@phlopalopagus9 жыл бұрын
Emil Madsen Well that sucks cause I think mine only charges to about 11.9 and I think its supposed to be 12.7 or something. Thats odd that it wont go into cali. If I figure it out ill drop the info here in case ya need it/want it.
@emilmadsen89729 жыл бұрын
Phlop Alopagus thanks man
@SaureHefePegorino8 жыл бұрын
thats like 30-50% less capacity
@vinanderson25359 жыл бұрын
Doesn't work.
@cp18555 жыл бұрын
Filming too close
@Erik740t2 жыл бұрын
Too far away you mean?
@jameshankssr4663 жыл бұрын
Best way to Calibrate that charger is throw it in the trash and buy a real charger
@Erik740t2 жыл бұрын
The charger has actually done a great job and I had the same lipo packs cycled hundreds of times and didn't lose capacity or flight time.