How to Change a Lawn Mower Tire | Tubeless Tire Change

Рет қаралды 154,874

2 жыл бұрын

If you need to change a small tubeless tire on your riding lawn mower or other lawn and garden implement, don't worry. Its not super difficult and you can do it with a few tools. This takes a little patience but its not hard to dismount and remount a lawn mower tire.
-- Affiliate Links to Products Used --
Tire Iron Set - amzn.to/3BeHbiw
Spray Bottles - amzn.to/3jeHi7A
Valve Stem Installer - amzn.to/3sLJXsL
Carlisle Turf Saver Tire, 15x6-6 - amzn.to/38eJHZW
Replacement Valve Stems - amzn.to/38buhFC
Longacre Tire Pressure Gauge - amzn.to/3ji5wOh
Valve Core Remover Tool - amzn.to/3ziGpQZ
Utility Knife - amzn.to/3sLrEnz
Super Clean Degreaser - amzn.to/3BdGgPr
**Super Clean Sample Pack Giveaway Rules**
- Must have a valid US Address
- Leave a comment on this video telling me what you need to clean up with Super Clean. Please keep comments clean as well.
- Valid ONLY for 2 weeks after this video goes live. This giveaway will end on Sept 11, 2021 at midnight. Winner will be chosen from the comments on 9/12/21.
- Winner will be picked at random from the comments and will be contacted through KZfaq to get your shipping address. Super Clean will be shipping you the sample pack
- This giveaway is in no way affiliated, sponsored by, or associated with KZfaq. Please see the KZfaq Community Guidelines for more info. kzfaq.info...
- Any Personal data collected will be solely used to ship the product giveaway. No Private Data will be collected.
- Good Luck, and Thanks to Super Clean for offering this sample pack
-- Visit My Website--
www.homebuiltworkshop.com/
-- Ways To Support HBW --
www.homebuiltworkshop.com/sup...
-- My TeeSpring Store --
teespring.com/stores/home-bui...
-- My Amazon Affiliate Store for recommended products--
www.amazon.com/shop/homebuilt...
-- Join the HBW Built not Bought Facebook Group --
/ 623919504748705
-----Connect on Social Media-----
/ homebuiltshop
/ homebuiltshop
/ homebuiltshop
/ homebuiltshop
-- Join the Community on my Website --
www.homebuiltworkshop.com/com...
-- Check Out My Handmade Guitars --
www.hayleyguitars.com/
----- My Mailing Address -----
Home Built Workshop LLC
P.O. Box 84
Peyton, CO 80831
-- Join in on My Weekly Live Stream (events calendar) --
www.homebuiltworkshop.com/eve...
Please remember when using tools of any type, there is the potential for injury. You are responsible for your own safety. Make sure you know how to use your tools properly, work at your own risk, be safe, wear your safety gear, and most of all, have fun!
#lawnmowertires #tirechanging #tubelesstires

Пікірлер: 150

@homebuiltshop 2 жыл бұрын

A huge Thank You to Super Clean for offering this sample pack giveaway. I sent the video to the Super Clean team to choose the winners. They couldn't choose just one so here are the 3 winners of the sample packs. Neptune's Creations Hayseed Shawn Olson Congratulations, and get ready to clean up some filthy stuff.

@Chitboxgarage 10 ай бұрын

Love to have some

@dastardlydave1455 2 жыл бұрын

Wish I saw this years ago. Tried to change a tire on my dad's mower. Couldn't get the new one on. Ended up at a tire shop. Probably needed those tire spoons. Thanks Jeff.

@homebuiltshop 2 жыл бұрын

Thanks Dave. Those tire spoons and soapy water really make it a bit nicer. Lol.

@JH-pn6zd Жыл бұрын

The ratchet strap worked brilliantly! Thank you!

@homebuiltshop Жыл бұрын

Its saved my bacon more than once. Lol.

@briandunn3315 10 ай бұрын

Clamp on the workbench, that's a good idea, going to have to try that!

@jimbond24 2 жыл бұрын

Jeff, some tricks and tips of mine are to use dish soap without water, last a bit longer when it’s being difficult. You didn’t mention getting the bead of the tire below where it seats on the rim. The rim is actually designed that way so one side can slip more towards the center of the rim to slip the tire on around the rim. Lots of times you may not even need spoons to put it back on. I recently had to do this on a log splitter and didn’t even take the rim off the splitter. Sometimes with the tire on your bench lube up the rim and tire and push the rim onto the tire while turning the rim works. I would also recommend you spray your valve stem both around it and on the core to check for leaks.

@boballard6040 3 ай бұрын

Thanks.. nice to see you struggle as much as I did and I am probably twice your age! And you're right, a lot of patience is the correct tool.

@user-wp5oz9es7m Жыл бұрын

The clamp idea was perfect. Tank you so much!

@user-xg5wx9bd6m 4 ай бұрын

I like the cleaning part comes out a lot easier than me scrubbing with a rush. I need to do my rims. Bow covers engines, and my car and certain spots. Thank you. I believe your product will work very well.

@CaraHillVoiceoverArtist Ай бұрын

Great idea with the clamp. Going to go try that after I take a nap as at this point, I am about to go buy a whole new wheel. 😂 Thanks for the video!

@homebuiltshop Ай бұрын

I hope it worked for you.

@genetjones5150 Жыл бұрын

11:53 Thank you for the ratchet strap tip!! Worked like a charm on our lawnmower tire that went flat over the winter. Without the strap, it was just wobbling all over the rim and letting air out uncontrollably.

@homebuiltshop Жыл бұрын

Awesome! I'm glad you got it. Its saved me a few times as well.

@uselessness7 Жыл бұрын

Had the same issue, worked great.

@user-oe6fp3ck6f Жыл бұрын

I'm just getting started. So far so good! Thank you, Jeff.

@sojournsojourntraveler1203 Жыл бұрын

This is a great video with some great tips. One important thing I have not seen on the lawnmower tire change videos IS ,along sure the back side of the tire is in the valley of the rim so your not fighting it.

@Doolie77 9 ай бұрын

After HOURS, and maybe a bit of cussing, this is the BEST vid ever! ESPECIALLY WITH ANOTHER VIDEO he made when he was told to, use STRAIGHT DISH SOAP!!! After a dozen vids, with no success BEFORE WATCHING THOSE 2!! THIS is the way. The clamp was a game changer, the undiluted soap was the icing on the bead! 8 minutes to mount a new a new rubber on the rim.

@homebuiltshop 9 ай бұрын

Thats awesome! I'm glad you got your tires on. Thats pretty fast too.

@lewisgiles8855 10 ай бұрын

Thank you brother, many of us need this video in the summer time. Thanks again!

@coloringoutsidethelines9755 2 жыл бұрын

YESSS! PLEASE...show us the rear tires! I just did my fronts this spring, but have been dreading the rears all summer!

@homebuiltshop 2 жыл бұрын

OK, I'll do it when I get ready to replace the rear tires. Should be later this fall I think.

@richardwinfield5216 Жыл бұрын

Show us the rear tires ,, please

@originalmetalhead73 2 ай бұрын

THANK YOU, the clamp worked fantastic! However, I needed two ratchet straps (one on each side of the tire) to get the bead set and for the tire to take air. These were very new and inflexible tires with strong sidewalls. I could set the bead on the tire I took off could by using one strap, but it was about 20 years old.

@marty01957 4 ай бұрын

Hey Jeff! I've been a subscriber for awhile and hadn't seen this video. I spent an hour this morning trying to mount one tire, then came to youtube for a refresher vid. Then spent the next three hours getting both tires mounted. The point is this vid didn't pop up till I sat down here this evening. Lol! Oh well, good vid as always! Thanks for posting!

@Forever_resist 11 ай бұрын

Great video. The ratchet strap technique works great! I wish I had known that years ago

@homebuiltshop 11 ай бұрын

Its been a real lifesaver for me too. I'm glad it worked out for you.

@scottcrossman2290 Жыл бұрын

This was more helpful than others I watched. Others didn't suggest clamps and tire spoons. Also, great suggestion to get tire warm.

@homebuiltshop Жыл бұрын

Awesome, thank you!

@deoeers 6 ай бұрын

Thanks mate. Good instructional video.

@Neptune730 2 жыл бұрын

I have to do the same thing on a trailer I built for my mower. I have the added fun of putting an innertube in mine though. Thanks Super Clean for letting Jeff give out a sample pack. I could use one. I'm redoing the brakes and all the brake lines as well as a bunch of other work on a 1997 Dodge Dakota.

@homebuiltshop 2 жыл бұрын

I almost went with a tube, but all the tubes I could find locally were at least half the price of a tire. Since I still had to break at least one bead loose, I figured I may as well change the whole tire. Now I need to do the rear tires. Lol.

@homebuiltshop 2 жыл бұрын

Congratulations, Super Clean has chosen your comment to receive a sample pack of products. Please send me an email to homebuiltshop@gmail.com with your shipping address. Super Clean will send you the sample pack.

@rickhartman3960 10 ай бұрын

Super great video. I just got my new rear tires delivered for my rider, gonna install them on the rims today. One thing most of u dont know is dish soap has patrolum distillates in it. It can eat up ur tire over time. They do make a white paste that tire repair shops use but who has tire paste laying around? I have a better idea. I am going to try Ky- jelly in a spray bottle mixed with a little water to slip on the tire to the rim. Yes, I said Ky- jelly-lol. It's water based so no deterioration later on. I also learned to NEVER use tire bead sealer to a good rim. The bead sealer will corrode a rim making the rim worse. Thanks again for a great video.

@na9260 Жыл бұрын

Great idea to use clamps. Thanks

@midgardner Жыл бұрын

This was thorough and clear. I appreciate the straight forward and expansive explanation. This is all the instruction I need to change my lawn tractor tire,

@10Seconds2Blastoff 2 жыл бұрын

Thanks for the video and tip about the ratchet strap. My tubeless ride front tyre went flat and tyre bead on one side let go. I couldn’t get it to reseat just with compressed air but when I put the strap around it, it popped on very nicely.

@homebuiltshop 2 жыл бұрын

Awesome! I'm happy to hear it worked for you. I've used it several times and its a neat trick to have up your sleeve.

@timmcardle959 11 ай бұрын

You can always squirt some starting fluid in there and light her up much more dangerous but much more fun

@randelcross 2 жыл бұрын

Nice job Jeff! My weekend project last week was my wife's bike tire.... it was probably easier than a tractor tire but I have a point! I was curious as to the leak... tire off the rim, put air in the tube and baptized it in the kitchen sink, only to learn........ it was the Schrader stem!! Ugh, I changed it out, lesson learned, saving the new tube for when I really need it. Holds air now!!

@homebuiltshop 2 жыл бұрын

Darn those leaky stems. Lol. At least you have a spare tube now.

@motemotola9821 Жыл бұрын

great video, very well done and funny too !

@tedsmith5083 7 ай бұрын

Good video! Thank you 😊

@carltoneddyiii809 Жыл бұрын

Been Trying to clean my Cub Cadet tire rim just as in this video, I love to get a sample to aid me in this issue

@shadow8479 5 ай бұрын

To break the bead on those smaller rims, I used my 20 ton press and a 2x4 about 6-7” long, worked beautifully

@bobbg9041 Жыл бұрын

Thanks, pulled tips from 2 different people, 2 years ago I just bought new rims and tires already mounted, but it had a set of these plastic bushings berrings that worked but not really good, my original cub cadet wheels were in very good shape with real berrings and zerts this junk set had a cheap plastic zert on the inside of the rim. I took the old tires off my factory rims pulled the new wheels back of the tractor after using them for 2 years and they were very muddy dry mud we've had one of the wettest summers I can remember in the last 50 years so it was pretty bad. Cleaned up the orignal rims put in new valve stems set aside busted down the new wheels and put the rubber on the orignal rims. Its pretty ez to bust the bead on that size rim with just 2 hands and pushing down. I also put agro type new tires on the back I had to buy and use a harbor fright tire machine for them and it worked really good pice of cake. I also got 2 long tire spoons from harbor freight. But you cant change a tire on a rim with a 3/4" shaft hole with it. You would need to buy the small one but it may not work for rear wheels as good and these agro style tires don't stretch as ez. To take what I did to a lawnmore shop or tire store your looking at 10 each or up to 40 each wheel. Its cheaper to just buy the tool and do it at home. I belive I could make an adaptor to do smaller tires on the big machine. What I did was used a black and decker workmate and put a long old screwdriver with a missing handel and it had a large flat spot the end of its made to hit with a hammer so it has to be 70 years old or more. You put your 2 long tire spoons in one side the long shaft is taller then the tire one spoon on one side the other on the other side you use the center shaft to pivot from as you push each spoon past the other like opening sizzors this pulled the bead up over the rim, works both sides keep the bead from the back side in the center of the rim at its smallest diameter that gives room for the tools. The tires pop right off the rims dry.

@INTERNA9 3 ай бұрын

WOW! It works. Thanx. Long time ago same way ..I did dirt bike tire...it was a pain.ha..ha...

@dianahaldi1 Жыл бұрын

thank you, i popped my tire, and im new to lawn tractors if the super clean offer is still available i'd appreciate a set

@walthyde5159 2 жыл бұрын

i really need to clean up my truck some and some old muskets as well

@digi3e 9 ай бұрын

Thank you!

@islandgal500 2 жыл бұрын

Working on adding an inner tube to my flat tubeless rear mower tire now. Really stiff tire so will use the heat of a hairdryer around the center of the tire and then the soap/grease since I don't have a heat gun or hot sun. A mechanic will take half a day to get to and travel $$.

@newriverdiggers5821 2 жыл бұрын

I just blew a front strut out and have hydraulic fluid all over the inside wheelwell and suspension. Super clean to the rescue.

@homebuiltshop 2 жыл бұрын

@newriverdiggers5821 2 жыл бұрын

@@homebuiltshop Thanks so Much and Thanks so much to Super Clean. Austiville Virginia is going to get a little bit cleaner thanks to others generosity.

@user-su5fh2zl9y Жыл бұрын

Yes! Back tire

@homebuiltshop Жыл бұрын

That one didn't work out very well. Lol. It seems as though I needed bigger tire irons. kzfaq.info/get/bejne/fMV8lraVtZ3FeKM.html

@user-zx7nq3bk4p Жыл бұрын

I am going to do the same thing as you, but time 4 . I need some super clean.

@rockpadstudios 8 ай бұрын

what a great idea :)

@zackmorehouse 9 ай бұрын

I like the use of clamps and changing the valve out. And easier way to break the bead is to use a 2x4 cut at an angle

@sojournsojourntraveler1203 Жыл бұрын

EXTRA ARMS A couple of tricks / tools I have been guided to use is a "HEACY" steel plate with a 6" X1/2"bolt welded in the middle that I drop the rim over and tighten it down to stabilize the work. 2nd Is I grab the rim with vice grips so the tire does not move around and loose what I have gained. I am really considering building a breakdown machine for the little tires. 3rd If I am dealing with a tire that does not want to be air tight on the rim / rust pits etc. I use a layer of toilet ring bees wax smeared around where the tire bead makes contact . 4th If your dealing with a persistent leaking tire, what I would recommend first is changing the stem as the cores are happiest with a new stem . Break down the tire enough to install a new stem is easier.

@jeffingle8011 Жыл бұрын

I’m getting ready to change all four 1995 Sabre 1546G riding mower tires away from their host wheels. I need all of the help I can get with this project here in NC. Jeff Ingle - 425 Madison Dr., Mount Holly, NC-28120. THANK YOU FOR YOUR HELP!

@davidbraner5889 4 ай бұрын

I like the ideas for the clamps to break the bead and clamp the tire to the work bench. Recently had to change the front tire on my stepfathers mower, and he never told me he SLIMED it years before 😱!! Had to use a wire brush for the heavy stuff, then penetrating oil and time (about 45 minutes) and it wiped off. Would those Super Clean products do anything for that, or would you recommend the same if you came across that (something that essentially melts it off)?

@jamesburba1995 2 жыл бұрын

i need to clean up the back half of the chassis of my '81 C-10, prior to painting it.

@neutrodyne Жыл бұрын

Using that wood clamp to hold the tire is a great idea!

@paulwaldrop 2 жыл бұрын

Hello. Great video. I could use that. I have a greasy engine I need to clean.

@antonheidebrink7716 6 ай бұрын

next time put a long steel rod in a vice put the center of the rim over the rod and then use those tyre spoons the moment you have 1 part over the rim than you can make a scissor movement with the rod as center and than you get it real easy of i learnt this at a car garage where the tyre machine was broken

@petekumnik9024 2 жыл бұрын

I need to clean a rim after changing tire and other Lawn Tractor areas. Also general purpose uses of Super Clean.

@cal4625 11 ай бұрын

Had the same problem with my dry rotted mower tires. Added some Slime and it don't go flat anymore.

@f-xdemers2825 Жыл бұрын

I have a pig farm. It's on a recuperated field backfilled over a swamp contaminated by a leaky slurry pound of undetermined yellow stuff left from an abandoned military base. Super Clean please.

@foxiedogitchypaws7141 Жыл бұрын

Will super clean clean a mobile home outside without a pressure washer? Thanks

@kiltymacbagpipe 2 жыл бұрын

Bad you considered using a tubeless sealant on the tire? Helps to seal the bead and plug any small holes. I’m not sure if lawn tractors use the stuff but it’s handy.

@homebuiltshop 2 жыл бұрын

I think this tire had sealant in it at one time. There was a goopy residue in the tire. I've used it before on other tires. With this one being dry rotted, I decided it would be best to replace it.

@phillpholbrookjr.7084 7 ай бұрын

Some refrigerator coils need a clean 😊

@janghu1681 Жыл бұрын

辛苦了，這的確不容易…

@drcoffee5588 Жыл бұрын

I gave it a shot and ended up taking the two tires to a local tire shop and paid $10 each. Well worth the money. My medical insurance deductible is way more than $20 😂 But something you should do while the wheels are off. Pop off the rubber outer seal of each of the wheel bearings and re-pack them with grease. Mine were bone dry and probably original from 1994.

@znogaragego3421 11 ай бұрын

Or you can get preinstalled tires on wheels for a few extra bucks. You save labor and get new wheels too.

@kwootamuckbear9294 2 жыл бұрын

Nice experiment…You should have it all figured out on the next one😬

@jonjongx Күн бұрын

How has the tire held up ?

@jamesdumez8086 2 ай бұрын

I need to clean brake calipers and also lawn tractor wheels.

@robertyoung7027 2 жыл бұрын

would like to clean up my nasty grill.. super clean will work?

@steelfender 2 жыл бұрын

Informational, but the Pyro in me was sad you didn't use the exploding carb cleaner method to seat the bead. I need to clean up my dirty victrola motor...and I wonder if Super Clean is safe enough to clean the crud off of the shower?

@homebuiltshop 2 жыл бұрын

I really wanted to try that, but I think that may have to be an off camera experiment. Lol.

@jerrylalonde1646 Жыл бұрын

My hands are pretty dirty out in the shop and what I do out there is a lot of Grease I wouldn't mind using it thank you

@Lutzboater 2 жыл бұрын

I have a BBQ Grill that could use a good cleaning with Super Clean.

@scottb.2022 2 жыл бұрын

I really need to clean the chain and rear sprocket on my mountain bike. It's filthy!

@francesweese885 11 ай бұрын

We could use some help cleaning our wood shop hope you send us a good cleaning

@smokeyplaces2go Жыл бұрын

I have a question, my owners manual shows an inner tube (service item only) is a inner tube really required? And why is this a service item only?

@mario8077 7 ай бұрын

How about two years after the video? 🙈 Cleaning also the tractor tires and rims, thank you 😀

@johnnysheets7703 Жыл бұрын

I need to clean up a rear lawn mower wheel

@korgullironclad1149 3 ай бұрын

For anyone who watches this video, save yourself some struggle. When attempting to remove or mount the tire, push the bead of the tire down towards the middle of the rim and put your spoon in the opposite side. All tubeless rims are designed so that the middle of the rim allows the bead to move towards the opposite side and you won't have to struggle to get the opposite bead on or off. Then you can work your way around. Don't try to take huge bites at a time. Also, try to work with the rim on the bottom. Gravity is your friend. Especially when you start working with bigger tires. If you notice, at one point in the video, he can't lever the spoons into the middle because he's trying to pull the rim out through the top and it's in the way. Finally, keep in mind that the smaller the diameter of the center of the tire is, the harder it will be to remove and mount. And just like most things in life, lubrication is the key ;)

@Rusty_ok 2 жыл бұрын

I used to jump on the tire to break the bead. Clamps are a better idea, fewer twisted ankles. I have a very dirty heavy duty two wheel string trimmer. I tried a pressure washer and between the leaked oil and dust/ dirt it just does not want to get clean. I have never tried super clean, would it work on caked on oily dirt?

@homebuiltshop 2 жыл бұрын

I can't say I've never done that. Even the twisted ankle part. Lol.

@dottiedurden8113 2 ай бұрын

This is just exactly the same way I changed bicycle tires

@Earthmadegarden Жыл бұрын

😂😂😂😂😂 “it helps if you have like 4 arms”

@homebuiltshop Жыл бұрын

It would. Lol.

@mpilksjr Жыл бұрын

Link for the valve stems didnt work for me.

@thejacklegpreacher1793 9 ай бұрын

You do have forearms. 😂

@homebuiltshop 9 ай бұрын

Lol. True.

@hal12b Жыл бұрын

Could you just saw zaw off the old tires?

@homebuiltshop Жыл бұрын

I'm sure that would work too.

@shawnh2870 2 жыл бұрын

Should of just put a tube in it. Also you can pull the valve core out and put a couple ounces of plane old automatic transmission fluid in it. You will be surprised how well the ATF works

@homebuiltshop 2 жыл бұрын

ATF? I haven't heard that. I'll have to experiment with that. I almost went with the tube but all the ones I could find locally, weren't much cheaper than a new tire.

@vondelldaniels5380 Жыл бұрын

Enjoy the video, have grill could use an awesome cleaning.

@znogaragego3421 11 ай бұрын

Or you can get preinstalled tires on wheels for a few extra bucks. You save labor and get new wheels too.

@bwill578 Жыл бұрын

Hell I've cut the tire in a few spots and it's still holding onto the rim 😂. It's almost like the lip of the tire has melted to the rim 😮

@racmakes 2 жыл бұрын

❤️🙏🏻

@gavett2833 10 ай бұрын

Spoons?

@angelabrasseale7638 3 ай бұрын

I need to clean my grill and a tire rim

@bettinanstevens9259 Жыл бұрын

The easiest way to get the old tire off of the rim is to use your ox-acetylene torch set. Fill the tire with pure oxygen next you will need a two foot fuse.......lol 🤣

@mickeyking2972 Жыл бұрын

I need to clean a grill and an old truck that has been sitting outside for years.

@jackmarchioni3114 29 күн бұрын

After you got it half off why didn’t cut it

@johnmcquithy8995 Жыл бұрын

where's super clean available?

@jaceisaac2064 Жыл бұрын

I too need a good cleaner to clean lawnmower wheels. William Berry 2514 Glenn Place Jonesboro AR 72404 Thanks!

@rebekahmartin2698 3 ай бұрын

Yard machine Mtd rear tire removal

@michaeltwiselton2973 6 ай бұрын

seven year old tractor has three flat tires

@giovannipetitti1588 2 жыл бұрын

wooden holes 🤣🤣🤣🤣🤣🤣🤣💯❤️

@shawnolson8222 2 жыл бұрын

My son and I need to clean an engine on a farm truck we are turning into daily driver

@homebuiltshop 2 жыл бұрын

@frankrowland63 2 жыл бұрын

I cut the old tire off with ban saw

@homebuiltshop 2 жыл бұрын

Thats an idea I might have to try. Thanks for sharing that one.

@jacobwetherby 2 ай бұрын

CUT OFF THE OLD TIRE, use any circular saw, or grinder, use a good sized pry-tool (dull-rounded), to hold the tire away from the rim... cut the bead Also, use a large CLAMP , to break the bead... no air (hand ones work good) Lastly, use some motor oil around (both sides) of the new tire bead, and STAND on it to put it ONTO the rim, DON'T USE SOAPY WATER, USE OIL (one side first, use a clamp, use a rag to clean up the oil later) firmly hold onto something (pole, table) while you stand on it.

@nicholasl.6606 5 ай бұрын

Rotate the rim and it’ll slide in. What are you doing

@johnparrish6489 Жыл бұрын

Same as video steel wheels

@anthonyvallante-su1jm 3 ай бұрын

Engine bqy of a 1963 sw corvette

@tracykey9227 6 ай бұрын

Why would you be worried about damaging the old tire, taking it off, if you're taking it off because it's already useless and damaged? It'd be nice if you could get some cable Cutters in there and just cut the bead on each side of the tire and then just pull it off, but it's obviously tight enough as it is and you don't want to risk damaging the rim.

@monkeybarmonkeyman Жыл бұрын

Ya know... if you aren't going to reuse that old tire, just cut it off... not like they're steel belted or anything 😛Plus you get a tad amount of satisfaction for all those times it went flat on you.

@homebuiltshop Жыл бұрын

Thats a good point. Lol.