Have a look at other videos on our channel: 🔸 BMW 3 E46 car repair tutorial - kzfaq.info/sun/PLWep5LzT0sxlrZzJ2LwR3ZRbK2is26dj9 🔸 How to replace front springs / front coil springs on BMW 3 (E46) - kzfaq.info/get/bejne/ot6qjLSetrCdpGQ.html 🔸 How to replace a front shock strut on BMW 3 (E46) - kzfaq.info/get/bejne/btOYl7OTmsjclWg.html 🔸 How to replace wipers blades / window wipers BMW 3 (E46) - kzfaq.info/get/bejne/jrZ1ptl61J29lmg.html 🔸 How to replace front anti roll bar link / front drop link on BMW 3 (E46) - kzfaq.info/get/bejne/etCkYNucnrbLloE.html

drivin me crazy to see the old rear bushing being put on the new arm.. :( replace with new..

Good video but a couple of small adjustments needed. Firstly - WD40 isn't really ideal when used to dismantle components, It works here because they aren't actually rusty, but on a car used in salty / winter weather (aka british weather) you need a proper penetrating oil to get into the rust. (and they're available at usually a similar price / cheaper than WD40!) Second point - It's worth making a note / mark of which direction the bush was pointing before removing it from the arm to allow you to install it at the right angle (or as close to it as possible) or putting it back on the car will be a pain! Third point - WD40 makes lots of different types of rubber swell / degrade more quickly. So you'd be better off using a silicone oil / red rubber grease / motorcycle chain lube even! for assembling the bush. Fourth point - I wouldn't advise copper grease for the alloy wheel / brake interface. There are better alternatives (something that handles heat better) if you must use it, but lots of mechanics wouldn't recommend it at all! Lastly, If you're spraying grease near the disc you should be cleaning them off after as well to stop contaminating the pads. Like I said, overall it's a very helpful video, but just these few additions in later films would make it better still!

This is why I won't take my car to a mechanic haha who the hell uses wd40 to lube a rubber bush haha it'll fall to pieces in a few months from dry rot lol

Nothing out of the ordinary for a BMW leaking oil everywhere :)

Why would you reuse the same bushing from the old one??? Wtf

I wish I knew before in what mess I was getting myself into this guy makes it seem like is peaches and gravy, but it is not my tools to go was a mallet and grinder and lots of 4 letter words

Yeah mechanic here, penetration oil and rubber = failure. Grease. Use grease.

The most amazing thing to see here is that they appear to have found an E46 with no obvious signs of rust!!! I wonder where they got that.....A museum perhaps? lol The video is a useful guide, but why go to all that trouble to fit brand new arms, then refit them with a used bush? Really they should all be changed at once or ideally, replaced with poly bushes that will last a lot longer.

Never spray WD40 on rubber parts.

I have problem with one arm…the left is original mpack…..can I put myele hd on the right side ? Or they need be the same ?

I had no issue removing but i am unable to reinstall new bushing 😭 i need one of those table clamps maybe, and a table 🤯

thanks for the video and yes I just got an alignment yesterday on my 2005 Z4 but still noticed when I brake or coming down to lower speed sometimes my steering wheel shimmy or vibrate a little and goes away. Is this due to the lower control arm bushing you think? Yes I do hear the minor metal clunk when I turn at random or like a sound of crackling.

For the price you have to change out that lollipop WTF? order the full kit!!!

hi, Does the meyle product use well?

Link on tool to press it out

Good video annoying music

There is something wrong. I dismantled twin screws with 16 combination spanner not 18.

Subframe bolt????? 🤷‍♂️

This is a mechanic????? Lolololololo

Wd40 is very bad for rubber

Wurst how to video I've seen

Wd40🤣

Terrible how to video, blink and you'll miss