How to change front wheel bearing on FORD MONDEO MK3 Saloon [TUTORIAL AUTODOC]

No video

How to change front wheel bearing on FORD MONDEO MK3 Saloon [TUTORIAL AUTODOC]

Рет қаралды 20,852

autodoc.co.uk

Күн бұрын

Пікірлер: 23

@boosteddiesel1834 Жыл бұрын

Great video, it has shown me all the steps I needed to see and all of the tool information I needed as well. Thanks

@autodocuk Жыл бұрын

Thank you for your feedback! We are pleased to know that our video was helpful for you.

@thomasbrennan5837 2 жыл бұрын

Mate of mine is a mechanic and did the 2 front bearings, same model car, except where you have 3 nuts and bolts at end of wishbone, on my car there's 3 large solid rivits , not nuts and bolts, made job very difficult, is this a modification or have you experienced this before, thank you

@thomasbrennan5837 Жыл бұрын

@@leebenstead7171 thanks for info Lee👍

@ibrahimoruc5795 7 ай бұрын

buy Lemforder , it comes ready with 3 bolts

@AGF78 5 ай бұрын

I have read that the wheel hub nut torque is 290 nm. Are you sure that the nut torque is only 165 nm?

@autodocuk 4 ай бұрын

Yes you are right, the correct tightening torque is 290Nm.

@AGF78 4 ай бұрын

@@autodocuk It is very critical that you have the torque correct in the instruction videos, if this nut is to loose, the wheel can fly and someone could die!!

@johanbogg9158 4 ай бұрын

@@AGF78 the wheel will more likely just lock up, the brake rotor and caliper incl. holder will still keep the wheel in place, so if the nuts losens it will wobble, give of a loud noise as the rotor collides with the caliper and just mess up the front end. The wheel won't just fly off... The drive shaft will become a bit lose and will probably mess things like handling up well before the nut unscrews all the way. But yes, they will need to be more careful giving torque specs in the videos.

@lagunafishing 2 жыл бұрын

Approx 1 hour from start to finish?

@autodocuk 2 жыл бұрын

If you have all the necessary tools, then about an hour. AUTODOC

@rimmersbryggeri 2 жыл бұрын

Depends on how stubborn the nuts and bolts are. The lock bolt for the ball joint can be a pig. I would also reccomend to do the suspension control arms at the same time and probably the other suspension joints to while you are there if they have not been changed recently. ( Track rod ends & anti roll bar links)

@ronron7763 2 жыл бұрын

Given all tools handy, it would take about 3-4 hours first time. After first experience, you might do it by 1-2 hours. And so on, reduce your time on each further attempts. But normally these bolts are gone through thosuands of cycles of HEAT-WATER-DUST which makes them fused with rust and what not, that they get difficult to unbolt. So it would throw you odd curve to follow. Like needing heat gun, rounding nuts or breaking parts.

@absorbtheride 2 жыл бұрын

Pleased this vid is here, but shocked at the sloppy torque setting. Bloke went way over the set torque on the wrench each and every time. Ya should stop when you hear the click. Looks like he went a good margin over on every bolt lol.

@autodocuk 2 жыл бұрын

Hi! Thank you for your comment. We understand that mistakes were made during the replacement, and in the future we will try not to allow this to happen again.