THANKS!!! Im actually going to be making a new one with different bleeder bottle for brake fluid flush.

Oh definitely. Who cares about the easy part lol

That is my goal.

Thanks and welcome. will continue sharing =]

Thank you! Will do!

In the beginning it was that initial valve opening, but at some point all the small bubbles later on in that right rear had to be from accumulated air in system somehow. I probably have a small gap somehow since all the lines were replaced.

Glad you liked it!

Thank you. I tried to not make it too long but just the right amount of knowledge needed to share.

Thanks hope you continue to learn more from my content.

Thanks for the vote of confidence from my video. 🙂

Rcf is 1000ml so 2 of these bottles.

Thank you so much 🤗

You can. The MX72 works great with stock rotors.

I dont recall but I know I just forced onto the valve.

You can use a 5-7mm ID hose.

Hey Benny, you can use high temp silicone and or brake grease/anti squeal grease. I didn’t do it in this video but my brakes hasn’t squealed. This step is just a extra measure for those that do have brake squeal.

Thanks for watching!

thanks

I havent had issues with abs. Do you have the light on or something?

No lights.

Only thing would be if you burn through the wear sensors which can happen if you let the brakes wear all the way down.

No squeal. Stops better. I have been through 2 sets so far

If you watch my recent videos, I just changed my brake rotors. They are at 100k on oem rotors when I changed out

lmao. Ultimate "Endless" braking performance.

endless

Thanks for coming

Once a sensor goes off, you gotta replace that brake wear sensor that went off

@@thehuangbrosright on Thx

Very much so

Wear and tear. Aggressive driving and little rocks

@@thehuangbros appreciate the response bro. Do u know where I can find the paint codes for these calipers ? In the event they do chip ect. I definitely drive aggressively. I have the blue gsf brembos. Thanks again

@@jamiele296 i unfortunately dont.

@@thehuangbros a got cha bro. Keep making videos I’m getting an rc f soon.

To which bolt?

Hey Benny, when car is off and you’re working the brakes, the resistance you are feeling when pushing pistons back is the brake fluid. The brake fluid system is pressurized. The brake pedal is not actively working the mechanism in the brake reservoir unless you have car off and you pump the brakes.

Was I able to answer your question? Have anymore questions?

Thanks and welcome

You can buy it online from Lexus of course but the small clip im not sure if anywhere else stocks them. I currently have mine not attached on the fronts and ziptied away because I do visual inspections

@@thehuangbros does this not cause a sensor to go off?

@@dannyly8300 nope. The sensor goes off when brake pad is close to the rotor and touches.

Im forcing my rotors through 100k. Im still on stock oem original rotors. I am 2k away from 100k miles before I change to 2 piece

@@thehuangbros Hmmm interesting. Lexus says the rotors are 2pc slotted OEM and cannot be turned. Therefore Rotors must be changed along with pads......Your honest opinion on this.

@@I3PREDACON the RCxxx are 2 piece. RCF is not 2 piece. Slotted rotors cant be turned because the slots would diminish even more. If an owner does not track the car, I see no purpose in changing he rotors with pads every time. Its a waste if all youre doing is gradually slowing down to a stop from 65mph. A set of rotors in my RCF’s lifetime has been through 4 pairs of brake pads already. 2 sets of endless and 2 sets of oem brembo pads. All on original rotor from the beginning of its lifetime. Sure there is lip but does the car stop? Yes it does. So I dont see a purpose in changing out rotors everytime pads are changed just because they recommend it. Thats my honest opinion.

@@thehuangbros Yes. I figured.

They say you should. I did it in this video. Every time after I have not and it has been fine.

I made a one way bleeder the tube submerged in old Brake fluid. Thats really about it.

@@thehuangbros I didn't realize it worked that way lol. Guess I've been doing it the hard way for way too long 😂. Thanks for getting back to me. All of your videos are super helpful.

@@RubberChickenMan007 i appreciate that

In top of brake pads?

@@thehuangbros yea by where the pins slide

@@peterock9682 im honestly unsure why but the stock brembos are that way.

1000ml so motul comes in 500ml bottles so 2

@@thehuangbros thank you king

💯👌✅

thanks for the love. =)

Yup they are 380mm

Thanks so much.

but isnt it bread before it becomes toast? haha

You'll need someone very motivating to keep the person in the stomper role stomping. =D

Oh do you have a video on changing brake hose?

If it works, it works 🙂

Connected