How to change the Unloader | Kranzle Pressure Washer

Рет қаралды 15,034

4 жыл бұрын

Was this video helpful? Please LIKE|SUBSCRIBE|COMMENT
Check us out on Instagram - bit.ly/kranzle_
For the latest prices and specifications visit - bit.ly/kranzleunloaders
_____________________________________________
📞01925 44 44 64
💻 www.kranzle-pressure-washers.c...
📧 info@aquaspray.co.uk
📸@kranzle_
🐦 @kranzlepressure
📺 Kranzle Pressure Washers
-------------------
#kranzle #aquaspray #parts
Disclaimer: you accept all responsibility for any damage or injury to yourself or others if following any of my videos.
it is sad I have to put this, but if you do something wrong you could damage your machine or hurt yourself or someone else.

Пікірлер: 51

@FoodOnCrack

Wow, can't believe my grandfather's West German pressure washer had the unloader valve locknuts set at the wrong threads all these years. It had full pressure all the years but wouldn't do lower than 60 bar. Goes all the way now without the nylon nut backing out all the way. I suspect it might be the original unloader valve as it needed some new grease but other than that, no blockages, marks, cracked or rotten o-rings etcetera. And its been used by his painting/all-round maintenance business ever since the fall of the berlin wall.

@jeevanjunawane3841 2 жыл бұрын

Great sir

@sudeshputran69 3 жыл бұрын

Super

@keirnofear1692 3 жыл бұрын

Hi, my kranzle is only giving low pressure that red nob usually springs out when I pull the trigger on lance but has stopped doing that, resulting in low pressure I adjust it but no difference?

@the_microfibre_man Жыл бұрын

Might be a stupid question but should you wind (clockwise) the unloader valve all the way in?

@garybyrne2420 4 жыл бұрын

Is there any maintenance on the other side of unloader. Or as long as the spring in the valve works is it all good?

@MrSagsta Жыл бұрын

I have a kranzle160 TST. Left it out in the recent heatwave doubt that was the real cause lol. However the actuator is not operating the push switch. It's a attach to the pump body behind pressure gauge. Any suggestions please

@bennyzakaria 3 жыл бұрын

Hi, How to modify a Kranzle HD 7/122 becomes a HD 7/122 TS, using original parts?

@kidbanga10 3 жыл бұрын

My kranzle 1322ts is surging when stopped. When the trigger is pressed it works fine. No drop of pressure on gauge when pressed. When the trigger is released it surges every 15-20seconds. What would cause this issue? Thanks

@jspecmedia 3 жыл бұрын

How do I adjust the psi I noticed mine only goes to 1300 when it’s rated for 1800. Also need to state is I barely use mine and don’t have much knowledge about these pressure washers 😬

@beano6584 3 жыл бұрын

Any info or links at all?????

@motomuscl3 3 жыл бұрын

Where can I get a new unloader?

@nathanbarker3789 3 жыл бұрын

I've tried an 8mm socket and it doesn't fit in and I've got a thin socket and still doesn't fit any help

@kerndetailology7632 3 жыл бұрын

I’ll be doing this in a couple days : I received my machine with a bent unloader 😔

@falcondetailing2564 Жыл бұрын

Can I heck find a 8mm socket with a thin enough wall to fit.

@beano6584 3 жыл бұрын

Bought one of these brand new, 1152 tsp , £750 from a main dealer, pulsing straight out of the box, checked the unloader and the soap pick up hose junction for grit, nothing! At least the Karcher with its crappy plastic pump waited 5 years to start it!