man you have no idea how money your videos have saved me least I could do is like and comment

I have seen a lot of your tutorials. Thanks for sharing. No one in Argentina share this stuff. You are a genius!

Great video Hunter !!!!!.... finally getting back into installing my D15b vtec installed in my civic. Now to find a P28 ecu. Glad your videos are still around for refreshers !!!! God bless you and yours and hope all is well .

Great video, I'm learning my everyday about chips/tuning/converting. Thanks for the great info!

Thank you for this vid, it is a much-needed "go-to" type video!

Way better than anything on Hondata's site. They should sponsor you and use your videos for their own tutorials lol! Thanks dude.

I spent 3 hours chipping my ECU because I didn't know how to properly desolder and didn't plan on doing it ever again but after watching this I may give it another shot.

Great video, very informative!👍

Great video! I was always so scare of touching an ecu, but after this vid...im confident o can do it myself now...but how to tune? :[

the one handed tech...

Sweet video man hope your having a great day

ECU 101 !!! #HUNTERBOIZ

Mint !!!!!!!!!!

Nice. Ever use the quick release eprom holders with the locking arm? That’s what I used on the one I did. Just flip the arm and the chip falls right out with no prying. 👍🏻

i could probably pick you up an ecu at the junkyard if you want to pay for it and the shipping

Hello from Turkey!cI watched your video and liked it I have a 1.4 civic with engine code D14A4. The previous owner changed the transmission to manual. I am getting an a/t error. I have p3y-g51 ecu. Will the same steps work for me? OBD-1 ECU Thank you for your help!

Do you sell a chipped ECU for a 94 Accord EX Automatic? In by chipping it what would it release HP wise? I'm not looking for a lot of gain's only to make it a little quicker

So I just found out I have an automatic ecu . Probably why I'm getting a fuel cut while driving. Thanks

what did you use for jumper wire? piece of paper clip?

Question. Do you think an auto p28 would work on an auto d16y8? Found one for cheap and wanna make my car tunable without having to swap it😅

My first P28, mint. I have done two recently that I burned the solder right out of the board and fooked myself. This last time, I bought one that was already socketed and it came shot. The fuel pump wouldn't run. Sent it back to dude, he sends it back, ran mint for a week, then no fuel pump again. I bought another one and sent dude back a dog turd in a box.

Have a question I have a chipped ecu jus like your doing to this one you installed instead of taking off the 28 pin can I just install The Hondata chip on top of the 28 pin and then jus install those 4 pins for the data logging or do I have to take the 28 out all together

awesome video ,thanks !

let me ask you hunter. i have a p28 ehich is already socket and chipped. I want to buy hondata s300 only, is possible to modify again to install this? need female adapter instead of male like socket

I just got a stock 92 cx in September I messed up the ecu messing around with something i shouldnt have Bought another p05 of facebook It came socketed and chipped with an sst chip Theres other stuff in there too Question: my car runs fine but the cel stays on and my shift light is going bonkers I contacted the dude i got it off and he swears theres nothing on the chip... Will this damage my car in anyway Should i do the paper clip trick or something? Thanks in advance

I got p28on my d16z6 automatic i change transmission to s20 I got check engine light because the automatic solenoid socket I take out the solenoid only and put back on my conector soo no more check engine but now I going to swap engine to b18c1 vtec gsr 5 speed , wht is you recommend me or advice, thx.

I check,your video.is very,very good.im interesed in cheap my computer,my engine is a f23a1 vtec,the car is shif stick,or manual transmission.i need your opinion,your help.let me know what do you think

hello , can i put a on-off botton on J8, and run the car whit 2 Maps???

how about automatic b20b can use manual transmission

Yeah Buddy...!!!

Hey Hunter I have like 6 stock Ecu's let me know if you needs some. Good contents!

Another great video Hunter how do you know what resistor to use on R54?

If i sent you a nice shipment of ecu's would you cut a deal to put together a kpro set up for a d17? If so let me know. Thanks bud

hey man been watching and learning a lot from your videos I'm looking for some help and youre a Honda wizard so maybe you can answer this I had a knocking y8 pulled it out (harness is fuckin hackjob) found a d16z6 for 300$ I heard it run and pick it up Monday if I get the harness off it it will be auto and a auto ecu if I can should I get a manual harness and ecu>? also I'm planning to use my y8 tranny will any of this even work ?

I have a p28 and a P06. Im running p28 on a b7 but it aint chipped. I need it chipped

How hot does the iron needs to be???

hi bro. how about the ecu p2m automatic convert to manual its is possible bro.

Hey do I really need to put a new resistor for the s300 chip into a p28

why do you change the c14 capacitor and where can you buy one

help..!!i did rechip on P30 ECU..but vtec wont engage?what did i miss?

can you chip my 93 honda del sol automatic ecu?

Do you have to have data logging when chipping ecu

Hey man I need some help and was wondering if you could get in touch

Can that ecu work in a 2002 honda civic

hey dude im looking to chip my manual p28, what chip should i get?

Hey witch is the priming number

Vtec conversation?

How much for the service

Hunter can this be done with a p06 also? Or strictly p28

U sell them

How much do you charge

So much adv