How to Choose Wire and Fuse Size | (PREVENT FIRES) BASICS OF WIRE/FUSE SIZE

Рет қаралды 119,160

4 жыл бұрын

In this video I teach you how to calculate the correct wire size and amp-rated fuse for each load in your off grid electrical system! After watching this video you will understand the importance of cable and fuse size.
This week, we got the majority of our electrical system connected!
West Marine 12V Ampacity Chart: www.westmarine.com/WestAdviso...
Max Current to AWG Chart: imgur.com/jfpTGYm
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
BLOG:
projectvagrant.com
INSTAGRAM:
/ project.vagrant
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
PRODUCTS USED:
Victron Solar Charge Controller: amzn.to/33ewoVA
40A Renogy DC-DC Battery Charger: amzn.to/2pIlxUz
Renogy 2000w Inverter: amzn.to/34kDveN
40A Breaker: amzn.to/2o80biM
50A Breaker: amzn.to/34lACKu
250A Terminal Fuse: amzn.to/2oPmuK4
Red & Black 5/16" Bus Bar: amzn.to/2pIexal
12 Circuit Fuse Box: amzn.to/2pGLGD9
0-10AWG Crimper: amzn.to/2o9bc3t
10-23AWG Crimper: amzn.to/2LUrA1X
100ft 12AWG Duplex Red/Black Wire: amzn.to/2pEwgzb
25 Ft 4AWG Red/Black: amzn.to/2obzjyp
5 Ft 2AWG Red/Black: amzn.to/2oOHC34
10 Ft 8 AWG Red/Black: amzn.to/2odepyS
----
Camera: amzn.to/2zysVDm
Mic: amzn.to/2L2OD9l
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
MUSIC USED:
Track: Coffee Dreams - Le Gang [Audio Library Release]
Music provided by Audio Library Plus
Watch: • Coffee Dreams - Le Gan...
Free Download / Stream: alplus.io/coffee-dreams
Track: Memories - INOSSI [Audio Library Release]
Music provided by Audio Library Plus
Watch: • Memories - INOSSI | Fr...
Free Download / Stream: alplus.io/Memories
Wanderlust by Nomyn / nomyn
Creative Commons - Attribution 3.0 Unported - CC BY 3.0
Free Download / Stream: bit.ly/wanderlust-nomyn
Music promoted by Audio Library • Wanderlust - Nomyn (No...
▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬▬
Disclaimer: All Amazon links are affiliate links. By using them, we are able to sustainably bring you guys more content! Using our link does not increase your price at all, and we get a very very small commission off your purchase. :)

Пікірлер: 149

@tajladkin4971 4 жыл бұрын

Been watching way to many videos on wiring for my tiny house and this is definitely the best one! Thanks so much ✌🏼

@projectvagrant8197 4 жыл бұрын

I'm so glad to hear it helped you ☺️

@anthonymarino4260 7 ай бұрын

DID A GREAT JOB THANKS

@jasonniggel5374 4 жыл бұрын

Thanks man, this has been explained to me so many times but I think it will stick with your simple examples!

@projectvagrant8197 4 жыл бұрын

Glad I could help! :)

@randallprue4134 3 жыл бұрын

Thanks. That was clear and easy to understand. I enjoy the thorough explanations and elaborations.

@projectvagrant8197 3 жыл бұрын

You're so welcome! Thanks Randall ☺️

@MerajTypeBeat Жыл бұрын

Clear and concise. I appreciate you! 🫡💯

@JulietNovember9 Жыл бұрын

Great video. Answered alot of questions for me! 👍

@leeblock3379 3 жыл бұрын

Outstanding video! Thanks for the clear and informative video. Thanks for posting all your stuff.

@projectvagrant8197 3 жыл бұрын

Thanks for the comment! ☺️

@cmine615 2 жыл бұрын

I’m building a very similar setup right now in my sprinter so this was suuuuper helpful

@svrds10 3 жыл бұрын

Hard work put into this one earned a thumbs up and a subscribe... Thanks!

@projectvagrant8197 3 жыл бұрын

Much appreciated!

@whirlwindmgtow5534 3 жыл бұрын

Fantastic video. Very well done. I learned a ton in just 9 minutes. 👍👍👍

@projectvagrant8197 3 жыл бұрын

I'm so glad I was able to help! ☺️

@MesaMinis 6 ай бұрын

I learned so much from this video thank you! This is my system I’ve planned for my semi truck. 3000w 48v inverter 3000W/48V=62.5A 62.5A x 1.25%=78amps Round up to a 80amp fuse Wire size must Handel 62.5A Wire: 4awg 120amps max circuit breaker: 80amps

@beboops 4 жыл бұрын

Oh thank you thank you thank you lol. I've been watching videos and trying to get a proper understanding of fuse sizing. I finally got it with your example near the end and the way you worded it. Oof! Ok I think I can finally start sizing my wires and fuses for my solar install! I just finished installing the panels on my roof, so I've been breaking my brain trying to figure out this next step 🙏🏻

@projectvagrant8197 4 жыл бұрын

I'm so glad I was able to help you! Thanks for commenting ☺️

@philiolynott4886 3 жыл бұрын

Have been looking all over to get a good understanding of how breakers are sized! Thanks!

@projectvagrant8197 3 жыл бұрын

Glad to help!

@user-ng5sr5bd9o 4 ай бұрын

Love the video man. Super helpful.

@paddygora8413 8 ай бұрын

I have saved this video for reference. Great explanations👍

@penielmubita7116 4 жыл бұрын

This video helped me a lot...hungry for more of your content!!!!

@projectvagrant8197 4 жыл бұрын

Glad to hear!! More is on the way :)

@urolisa Жыл бұрын

After watching you finally prepared to wire my boston whaler 15Ft proyect, thanks

@runawayrose6320 2 жыл бұрын

Thank you for the chart you saved me more aggravation then you'll ever know Bravo!!!

@projectvagrant8197 2 жыл бұрын

You're welcome :)

@deirdre444 3 жыл бұрын

Fantastic!! Made perfect sense.

@marisolmedina-gx9tf Жыл бұрын

Thank you for your education and teaching

@justinlyle7831 2 жыл бұрын

Great video man 💪😎

@brentmitchel3167 2 жыл бұрын

Very well explain thank you

@1212mhd 3 жыл бұрын

very well explain 👍

@Ibian666 2 жыл бұрын

Good vid, agree with everything.

@stevenscott9750 2 жыл бұрын

Very informative thank you. Steve UK

@s.mendez7160 2 жыл бұрын

With a lithium bank, you might want to replace that breaker with a fuse that has a much higher AIC rating. A Class-T fuse has an AIC of 20,000. And it's response time is much faster than a thermal breaker. Your videos are awesome and well produced!

@WizzRacing 2 жыл бұрын

That is not true.. ANL fuses allow for Inrush Startup current...And ANL fuses are slow blow just for that reason..If you want a fast blow fuse. You need an ANN fuse... And breakers are not slow blow..They detect short to ground faults. And will trip the second they see that..Ground fault are even faster. They trip within 50ms... I would add... You use Automotive grade wiring..Not the same stuff you use in a house..You also use Automotive grade TESA tape to wrap it inside a wire loom..

@rrvallance 3 жыл бұрын

Great video

@Just_An_Idea_For_Consideration 10 ай бұрын

Excellent!

@commandant30 4 жыл бұрын

Thanks a lot man, your chart or table or whatever we should name it, abt amps and sizing fuse is really helpful, which I could not find such info with ease in other videos. Thanks again

@projectvagrant8197 4 жыл бұрын

You're welcome! Glad you got some value :)

@stevesidare2493 Жыл бұрын

Thanks , I really appreciate the video! I'm considering running about 15 ft of wire from my Jackery 240's 12v socket to the back of my Transit Connect. I want to run a sound bar (via a 200W or 300W converter at the back), some LED lights (including USB), a 12v or USB rechargeable fan, plus 1-2 other USB things - like a phone recharger... ALL from a switched splitter. Do you think 16 awg would suffice? Do I need a fuse?

@Olly3pow 3 жыл бұрын

Awesome, Thank you ✌🏽

@projectvagrant8197 3 жыл бұрын

Thanks for commenting 👍 & you're welcome ☺️

@omoomoruyi4537 Жыл бұрын

Helpful as I'm trying to figure out why mine has fuse cut off on a 24v 280amps lifepo4 batteries.

@paulblueoasis5608 2 жыл бұрын

Excellent

@joephillip7503 3 жыл бұрын

Is there a chart available that that shows the gauge achieved when combining which gauges?

@Apanhwar12 2 жыл бұрын

Hello thanks for the video, i have a question as i am desginging a system of 11kw of solar panels, each panel is rated 540w and Short circut current 13.55qmps. Recommend on panel for series fuse is 25amps, i was wondering if i install 21 panell and make 2 strings. 11panels and 10 panels then at the output what ratting of dc circuit breaker should i use as the mppt charge control is used in inverter and voltages keeps fluctuate as per irradiance. So how to design dc circuit breaker for both strings.

@KR7PT 3 жыл бұрын

Well made video and a good description - now comes the dreaded part of buying 40 feet of 4 AWG cable.

@projectvagrant8197 3 жыл бұрын

Thanks so much for the comment :) glad we were able to help!

@IntrepidJordan 3 жыл бұрын

Super helpful

@projectvagrant8197 3 жыл бұрын

Glad it helped

@markthompson1796 3 жыл бұрын

Thank you very much.

@projectvagrant8197 3 жыл бұрын

You are welcome! Thanks for watching & commenting!

@onetrackfun3045 2 жыл бұрын

your max current to awg chart seems to be different then some others. How do i know what awg to use for my battery to bus bar ? im finding a lot of different info for max current to awg..

@averykevans6894 3 жыл бұрын

Anyway you could do a video about your solar wiring? About to jump into vanlife and as most, solar is confusing. If not a video maybe could answer a question... Looks like everything is ran through your busbars. Is that correct? I looked at simple solar plans and decided it was going to be easy but now that I have all the stuff for a larger system I am very confused. Essentially, I'm good with the main objective of your video, but am more so interested in knowing what exactly you're doing in the timelapse of this video aha.

@noahriding5780 8 ай бұрын

Will circuit breaker switches then turn off when a certain temperature is reached? (on their own?)

@hawaiidogs9277 Жыл бұрын

Ty sir

@leonas3840 4 жыл бұрын

Good video

@projectvagrant8197 4 жыл бұрын

Thanks Leo :)

@MindDezign Жыл бұрын

Great

@ThePhatWabbit 3 жыл бұрын

Do you size your fuse and wires for an inverter's normal power, or an inverter's surge power?

@joeo7257 4 жыл бұрын

Good job. Very clear. New subscriber. Just to be clear, solid strand Romex wire is only for the AC side, right?

@projectvagrant8197 4 жыл бұрын

Solid strand will work, but multi strand is preferred in a camper because it will hold up much better to the vibrations/movements. Solid strand is more likely to break off/snap in that setting.

@BlackJacketJones 3 жыл бұрын

i don't understand why i'm finding sources online that give conflicting information about max amps for wire sizes. For example, the link you provide claims that 2/0 wire can handle 330 amps, but i have found at least three other sources that claim 2/0 wire can only handle 175 amps. which is it???

@projectvagrant8197 3 жыл бұрын

From my understanding 2/0 can handle 330A. 175 amps can be handled by 2 AWG wire easily and it's a good deal thinner than 2/0

@gabrielheard2287 Жыл бұрын

Hey I know this is old, but 2/0 is 00, (two zeros, and 2 is just 2

@andufuse 2 жыл бұрын

Got it.

@sreekumarUSA 3 жыл бұрын

102620/0411h pst. Thank you for the informational video. I learned from your explanations and experience. Stay safe. 73s...

@jasonh4167 2 жыл бұрын

I have a question.. i have a led light bar on my jeep and the in line fuse (30A) corroded due to moisture. I got a replacement one. But im thinking the wires are larger then light bar's original wires. eg. 16ga. Light/ 12ga. Fuse. Fuse is rated for 30A. Would i see a light output drop?

@projectvagrant8197 2 жыл бұрын

If the wires are thicker than original you shouldn't have a decrease in output, if anything you should have a increase as thicker wire = less resistance and less resistance = less voltage drop over the distance of the wires. The one issue I see here is that I do not believe a 30A fuse is the right size for a 16AWG wire. So if you get a short there, the 16AWG wire may catch on fire before the 30a fuse pops.

@joaquinguillen3731 3 жыл бұрын

Can you insert a drawing or sketch step defining how you connected all together. Thank you

@Navillus2273 3 жыл бұрын

Nice video! Can you provide an explanation. Why a fuse is needed between positive battery terminal and positive bus bar, as all the devices have fuses after the bus bar. Also the fuses between bus bar and device, where should it be located? Closer to bus bar, or the device?

@projectvagrant8197 2 жыл бұрын

The fuses should be as close as possible to the battery. You want the fuse as close to the battery to minimize the possibility of short circuiting before the fuses. If you have a short circuit happen and the fuse is on the other side of the wiring, it will not break the connection when it shorts and you'll likely have a fire. There are 2 reasons I put a fuse on the battery terminal 1) my inverter doesn't have a fuse so it works as the inverters fuse 2) it also works as a "master fuse" so if there is a short and for some reason another fuse doesn't break the connection, this one will.

@brandonstewart7145 16 күн бұрын

How did you figure out what size fuse to use on your battery?

@beboops 4 жыл бұрын

Heya! I have a question for you :) I always try to cross-reference any info I get so I can confirm what I'm learning is accurate. I've been trying do that with Max Current per AWG size for fuse sizing, and gosh is there ever conflicting and confusing information all over the web! So my question is how and where did you get the chart that you used in the video? I'd like to be able to cross reference it with multiple sources, so its provenance and what name it goes by or search terms you might have used would be very useful!

@shofarsogood7504 2 жыл бұрын

It’s seems like no one knows and no one is answering. I’m frustrated too!

@dmmak2678 Жыл бұрын

Yes, I was also looking for the chart for wires size versus max current, but could not find it...

@dmmak2678 Жыл бұрын

After looking closer, I found the chart link, in his description...

@shofarsogood7504 Жыл бұрын

@@dmmak2678 if you check out battle borns wire chart it says 8 gauge should be able to carry 85-150 amps where this says something much lower. That’s the issue. Why the discrepancy. Have you( or anyone) found an answer?

@dmmak2678 Жыл бұрын

@@shofarsogood7504 I was looking for the chart he used, online, which I found. But in answer to your question, I do not know why the differences between the wire charts...as you know, there are many different types/ratings for same size wire, which might have something to do with it...

@theusconstitution1776 3 жыл бұрын

Did you use regular 12 gauge Romax? Is it or is it stranded wire? I’ve always been taught the DC current runs on the outside of the cable that’s more stranded wire make life easier for your current? Good video

@projectvagrant8197 3 жыл бұрын

I believe the wiring I used is linked in the description. I mostly used Ancor marine wire duplex red/black 12awg for everything except the things that pull a lot of juice (inverter, chargers). Definitely only use stranded, as it will withstand a mobile application much better than solid wire.

@theusconstitution1776 3 жыл бұрын

@@projectvagrant8197 ❤️🇺🇸THANK YOU SIR! INSTALLING MY OWN “BACK UP” SYSTEM. UPGRADING MY RENOGY 2 PANEL SYSTEM TO 4...100 WATT PANELS. THANK YOU FOR YOUR TIME AND YOUR VIDEO SERIES❤️🇺🇸 GOD BLESS OUR AMERICA, CONSTITUTION AND D.J.T.❤️❤️🇺🇸

@panthergaming732 2 жыл бұрын

Hello . where should dc fuse be installed, in the negative wire or positive?

@projectvagrant8197 2 жыл бұрын

Positive wire. As close to the power source as possible to minimize possibilities of short circuits

@projet2907 2 жыл бұрын

Thank You for this video, very well made. I wish I would have seen you di the cable lugs - crimp in a slower manner :-0)

@projectvagrant8197 2 жыл бұрын

Thanks for the comment! Getting those crimps right can be kind of a pain. If it's the smaller ones and you're using a racheting crimp tool, they definitely have a "right" way to be turned. Unfortunately every time I use them I have to figure it out and usually waste/ruin 2-3 connectors on my first one . If it's the big lugs you're talking about it's pretty straight forward as there's no special orientation -- but I have had to crimp those big lugs a couple times in different places to ensure it's tightly holding the cable (e.g. sometimes the lugs are longer than the clamping area of the big crimper, so I'll crimp the first half then the 2nd half).

@projet2907 2 жыл бұрын

@@projectvagrant8197 Thanks for taking the time to respond and sharing some of your experience. It still would make an interesting video !. I have a ratcheting crimper and other,, I recently tried about 4 different hydrolic crimper off of Amazon. None had the same size Dies,!! Measurement is in mm or not too accurate AGW . I crimped with the Hydrolics 2/0 to 6G. It's a puzzle to know what is a good crimp at times. I don't get what you are saying about a "right" way to be turned. What connectors are you talking about? I probably have not used those yet.

@Oppong24 2 жыл бұрын

Hello, Please I have this INVERTER Growatt 5KW 48V 220V Solar Hybrid Inverter SPF SPF 5000TL HVM-WPV-P Max PV Input Voltage 450V MPPT 100A Solar Charger Can Par . Please can you show me what type of battery I will need to run this?

@adrastosfilos9292 3 жыл бұрын

hi there, I have a question about fusing, why we can't just put a smaller fuse on the output than this big fuse between battery and inverter?

@projectvagrant8197 3 жыл бұрын

Because without a fuse there, if a short circuit happens, there is nothing protecting those wires. If there is a short circuit and no fuse, the connection will stay shorted and lead to the wires heating up, melting plastic, and likely start a fire.

@projectvagrant8197 3 жыл бұрын

It may be easier to put a terminal fuse on your batterys positive post and connect your inverter through that.

@daveyboy8907 4 жыл бұрын

Is 4 gauge wire thick enough for my 4 6 v batteries ran to a 3000 watt sine wave inverter?? what size fuse should I run between the battery and the 3000 watt inverter?? Thanjs

@daveyboy8907 4 жыл бұрын

So a 120 fuse for my 4 g wire? Thanks

@projectvagrant8197 4 жыл бұрын

3000 watts / 12 volts = 250 amps (assuming youre connecting your batteries to be 12v). So you need wiring that can handle at least 250 amps. And then fuse for whatever that wire can handle

@daveyboy8907 4 жыл бұрын

Project Vagrant 👍🏻

@nightstringers Жыл бұрын

you use breakers only . even is you have an inverter? cause I have seen breaks not being able to take the amps that inverters draw. I have a 2000 pure sine wave inverter . I can't find a 200 amp .breaker

@projectvagrant8197 Жыл бұрын

amzn.to/3BxvKEo

@brianrhodebeck6465 9 ай бұрын

heat rises. You had it right the first time. Just add a u s b fan To extract from the top.

@daveyboy8907 4 жыл бұрын

I just built a 400 watt solar setup. I bought 4 6 v batteries.. I have a 30 amp controller,, Should I use a 4o watt breaker for the controller?? also what other fuses should I use ?? thanks

@projectvagrant8197 4 жыл бұрын

Breaker/fuse size depends on the wire size you use, per the video. Every positive cable should be fused more or less. Fuse as close to the battery as possible.

@daveyboy8907 4 жыл бұрын

Project Vagrant thanks so much.. Some fuse the solar wire coming into the controller ??Should I do that? Its 4 100 watt panels in series with a factory renogy solar cable connecting to my 30 amp controller.thanks for your help

@daveyboy8907 4 жыл бұрын

Project Vagrant i am actually fussing the wires persay not the units.. I get it now . Thanks using 4 gauge wire and my battery cables are 1 gauge.

@projectvagrant8197 4 жыл бұрын

@@daveyboy8907 it's handy to have a breaker/switch/fuse on the positive wire coming into the controller from the solar panels because you do not want to leave the panels connected to the controller without the batteries. This is because without the batteries, there is no where for the electricity to go, and can cause the controller to overheat.

@daveyboy8907 4 жыл бұрын

Project Vagrant ok will do, thank you so much..

@tanioraaura1274 2 жыл бұрын

I definately had to watch this vid over and over again . Very grateful, its a like from me and Subscribed. Thankyou

@tanioraaura1274 2 жыл бұрын

I put my own system in the SmartSolar charge controller it's a MPPT 100 I 50

@carl8568 2 жыл бұрын

Just put of interest, what's the issue with using a fuse rated too high? Say a 200 amp fuse is no good on 4 AWG wire?

@projectvagrant8197 2 жыл бұрын

Because fuses are meant to protect wires from taking too much current (amps). I believe that 4 awg is only rated to something like 120 amps. If you use a 200amp fuse on the wire, and it shorts circuits or you put a device that pulls over 120 amps, then the wire will have more than 120 amps going through it until it gets over 200 amps and then the fuse will pop the connection. The issue is, in that time it goes over the rated 120 amps and before it hits 200amps, the wire will likely get so hot that it will catch on fire and begin burning things surrounding it and that it is connected to.

@carl8568 2 жыл бұрын

@@projectvagrant8197 Yes, makes total sense when you consider the fuse is there to protect the wire. I had someone telling me the fuse was there to protect the inverter. Thanks for the reply mate 👍

@jwells4853 4 жыл бұрын

If your building a tiny home, or stealth camper, I recommend DIYer's buy an UGLY's Book. It has guides for wire size and breaker/fusing sizes. As a Electrician, I will point out that the example of 10 gauged wire is rated for 30 Amps for THWN and THHN wire. 8 gauge wire is rated for 40 Amps THWN and THHN wire. Also unless your operating a dryer or electric stove, 12 gauge THWN and THHN wire is rated for 20 Amps and is well within the safety factors for a 15amp electrical outlet for house hold appliances. So far I like this explanation of his build but I thought I'd add some commercial electrical suggestions as THHN and THWN wire is available at LOWE's and Home Depot and cheaper than automotive wire.

@projectvagrant8197 3 жыл бұрын

I think THHN is not entirely to spec for RV application (not that most people care about the regulations -- I have some 14awg THHN connecting one or two circuits when I was in a pinch). I really appreciate your input and recommendations though, I have "loved" your comment so it hopefully pins to the top so viewers see it ☺️👍

@jwells4853 3 жыл бұрын

@@projectvagrant8197 Thanks, THHN is Residential and commercial rated wires. What it stands for is the ambient heat, oil and water resistance of the jacket of the wires. Stranded THHN or THWN wire in a build for a tiny home or van build should pass safety and inspections. Automotive wire is the same look on the jacket it will say THWN. If you buy it from a Automotive dealer, it will cost five times more than buying it from Home Depot or Lowes or your local hardware and Lumber supply. That's why I suggested it. The Wire gauge is what protects the electrical system, as long as you do not undersize your wires or over load the circuits. A 30Amp circuit requires a 10AWG wire and a 20 Amp circuit needs a 12AWG wire. a 15 Amp circuit only requires a 14AWG wire, but using a 12AWG on a 15Amp circuit breaker or fuse to feed a 15Amp rated outlet will not exceed the temperature rating of the wire or the outlet, especially when your fuse for breaker is rated for 15 Amps on a 120v circuit. It's just a little inside look to save you money on your build and not having to buy multiple sized wire. You'll actually have a cleaner voltage rating and less resistance. We use this method in the industry for clean rooms and neutrals on shared circuits in single and three phase wiring.

@robertgregory2618 2 жыл бұрын

The National Electrical code amperage tables do not apply to Rvs or boats. And generally welding cable or high amperage battery cable is used that have hundreds of strands and can support far more amps then THWN or THHN. We are talking about DC and high amperage battery systems.

@jwells4853 2 жыл бұрын

@@robertgregory2618 you can use thicker stranded wire, but you loose more volts because of the resistance. When you oversized you cables. You wire gauge should still follow some industry standards, to avoid potential fire hazards. Bigger cables on a converted circuit could accidentally allow more amps to be fed to a device that was rated for only a certain amount of current and could damage or even catch the device or fire or injure someone operating it.

@robertgregory2618 2 жыл бұрын

@@jwells4853 There are marine standards and others. Fuses prevent to much current. Problem is 12 volts. That's 3 more than a 9 volt battery for my remote control. 120 is 10 times more voltage hence not a lot of voltage drop to worry bout but 12 volts it become huge problem. Boats and rvs aren't covered by Nec but doesn't mean you can skimp on stuff.

@jessperci 4 жыл бұрын

Your videos are really well made! So I subscribed! However, I think to get more subs you need to work on your thumbnails, and make them more clickable!! ❤️

@projectvagrant8197 4 жыл бұрын

Thank you so much Jess! I really appreciate the honest feedback and I agree 100% -- my thumbnails need work! I would like to remake a lot of them. Do you think the pictures themselves need work or they just need different text/font/style to them?

@jessperci 4 жыл бұрын

Project Vagrant i think both maybe. make them more click baity so like for a video of you doing the electrical with you holding wires looking confused or like you’ve done something wrong. cuz then people will go “oo i wonder what happened” right now your videos are layed our very instructional which is good as it makes it easy to look for the one needed but maybe you could make your photos more click able but keep the instructional text x

@projectvagrant8197 4 жыл бұрын

@@jessperci thanks! I will have to start reworking them as I have time 🙂 we appreciate you!

@dianavr3291 4 жыл бұрын

Great video, sorry for a very stupid question, but how do you work out a mega fuse? ( still don't know what i'm doing as you can tell :) is it the same???

@projectvagrant8197 4 жыл бұрын

Hey Diana, not sure I understand. I have never heard of a "mega fuse" and did some googling but all I found was a brand of fuses named MEGA. :)

@dianavr3291 4 жыл бұрын

@@projectvagrant8197 hehe :) they are called mega link fuses, could be anything from 100-500A

@projectvagrant8197 4 жыл бұрын

@@dianavr3291 it will just follow the same principle, you want a wire that can handle at least whatever your fuse size is you're choosing

@maxgood42 3 жыл бұрын

Is it just me or did anyone else get lost with the imgur link ... I was clicking next for 3 hrs before I realized I was watching YT XD

@702goat 3 жыл бұрын

Solar panel system I have 325 watt solar panels they are 34 volt panels with a open current voltage of 42 volts and with max current at 9.32 amps. I have a Rover PG 60 amp MPPT solar charge controller with a max open current voltage of 150 volts and I plan to use the 48 volt system which is rated at 3200 watts for a 48 volt system. I have a 48 volt lithium ion battery 50ah with 3.5 kw. So based off the max wattage input I can only install 9 -- 325 watt solar panels which equals to 2925 watts and a open current voltage of 379 volts which is way over the max open current voltage of 150 volts rated for the charge controller, so my question is which pv module wiring configuration do I use to wire my 9 solar panels to my charge controller and also I checked the manual of the controller and there is no pv module configurations, please I need help which wiring configuration do I use to install my solar panels ???????

@projectvagrant8197 3 жыл бұрын

I *BELIEVE* you could do groups of 3 panels connected to each other in series. In series, this would be 34v * 3 = 102v. Still 9.32 amps, then connect those 3 groups together in parallel. In parallel, this would be 9.32a * 3 = 27.96 amps. So 102v max at 27.96a max. Please double check me on this but I think that should work within your parameters :)

@702goat 3 жыл бұрын

@@projectvagrant8197 thank you very much I will be testing this method next week

@702goat 3 жыл бұрын

@@projectvagrant8197 hi also I have another question, which amp Breaker should I use between the solar panel and the charge controller and which type of amp breaker should I use from the battery to the inverter ?

@projectvagrant8197 3 жыл бұрын

@@702goat you determine fuse size from a wire's ampacity. You determine wire size by current your device will pull

@702goat 3 жыл бұрын

@@projectvagrant8197 ok because on my solar panels it’s says fuse ratting 20 amps so do I use a 20 amp breaker between the solar panels and controller and I will be using 8 or 10 gauge wire

@tylerfidler5223 3 жыл бұрын

So what fuse would I use for a 60a DC to DC charger with 2 gauge wire?

@Oblivionsurveyor Жыл бұрын

They must of updated the chart because it does not match your chart.

@zenaasura1769 2 жыл бұрын

Ok one thing. Please buy proper cable gauge instead of having multiple cables running from the inverter to the batteries. The current set up will cause electrical resonance dissonance.

@projectvagrant8197 2 жыл бұрын

That was included with my inverter directly from Renogy and has worked fine for over a year and a half now.

@josephsadre8442 6 ай бұрын

Never use a fuse rating higher than your wires can handle

@Bellasafari 2 жыл бұрын

I could really do without the music... as is difficult enough to process all the electrical data...(why does so many yters think they have to spice it up with music?

@RVFreeDa 2 жыл бұрын

OMG the music makes it so I can’t understand what you are saying. Sorry but cut the music on sections you are trying to explain things! 😊

@onekerri1 3 жыл бұрын

The background (music?) was too loud.

@johnweber6147 2 жыл бұрын

It's obvious you know what you're doing and much effort went into it. But as a novice you went too fast for my old feeble mind and the music was distracting. Also If you could have explained every component once you had it all put together would have been helpful. I see you have a battery charger connected as well as a charge controller. Isn't a charge controller essentially a battery charger?