How to clean Honda CRF Carbs - FCR Flatslide - Parts and tools in description

Рет қаралды 410,547

9 жыл бұрын

I download a manual for every bike I work on! Get one for your bike here:
shareasale.com/r.cfm?b=510988...
Get your OEM parts from RevZilla with this link:
imp.i104546.net/PL5Ve
Check out MOJOMOTOSPORT for high quality billet parts for your bike :
mojomotosport.com?aff=141
I make commission from these links! Thank you for using them and supporting the channel!
AMAZON.COM
amzn.to/3iq6CVc - Accelerator Pump Cover upgrade
amzn.to/30FfQ9N - Fuel Mixture Screw - (must have!)
amzn.to/3ktNU0o - 450 carb rebuild
amzn.to/2YHb4ar - CRF Hot Start Nut
amzn.to/2DpvoG5 - JET Kit - (easy performance)
amzn.to/31whqtP - float bowl upgrade
amzn.to/2F6MfOj - jet cleaners
amzn.to/3ior6gP - Carb Cleaner
AMAZON.CA
amzn.to/3fdLz5W - fuel mixture screw
amzn.to/3gdE1Sf - JET Kit - (awesome for some easy performance)
amzn.to/3fdM5AU - hi perf float bowl sump
amzn.to/3gyAmOZ - carb cleaner
amzn.to/2Cc4PDC - carb jet cleaning needle set
We make a small commission on these parts. By purchasing with these links you help keep the channel going! Thank you for the support and we'll see you out there!
Honda CRF Carbs. Dirt bike sit for a while and now won't start? Check the honda crf flat slide carburetor. Honda CRF carb fuel can go bad in your dirt bike within a week. Contamination can also come in from your fuel tank plugging the honda crf carb jets. We'll show you how to take the carb out and identify all the components needed to get you riding again. Keep in mind, on some models the flat slide carb can be turned still installed in the bike, allowing you to remove the float bowl without removing the whole carb. Be sure to SUBCRIBE - new videos added all the time! Thanks for watching!

Пікірлер: 181

@CoteMotorcycles 4 жыл бұрын

Feel free to get in touch with me on FB if you have any troubleshooting questions! Support the channel and pick up these sick mojomoto parts for your CRF here >>> mojomotosport.com?aff=141

@bacardialpha3136 2 жыл бұрын

What’s your fb

@CoteMotorcycles 2 жыл бұрын

@@bacardialpha3136 just search Cote motorcycles and it should pop up.

@daveshuk26 7 жыл бұрын

Thank you so much! Excellent video! I followed step-by-step and completely cleaned my carb without any issues! Keep the videos coming.

@michellatour150 8 жыл бұрын

Thank you very much for posting this. I regularly maintain and service my friend's CRF250R, suspension overhaul & re-valve as well but the FCR carburator (versus the much simpler Mikuni on my YZ125) was always intimidating. Great step by step of the different sub-assemblies shown, not having to tear it down to a hundred loose pieces at once. Merci / Thanks !

@erichameister7000 7 жыл бұрын

i wanted to thank you for this video. super helpful and informative! thank you for taking the time to do this.

@krishebert6372 5 жыл бұрын

That was very educational and very professional! Southwest Louisiana thanks you!!!

@nivag63 7 жыл бұрын

Nice vid, thanks for helping and taking the time to produce it

@mrboomlive807 8 жыл бұрын

Great video! You explain things clearly and have good camera angles. There are a few other vids about this that don't come close to the quality of yours. Thank you.

@CoteMotorcycles 8 жыл бұрын

Thank you for the comment, glad you liked it. Be sure to share so we can make more!

@ebonics85 2 жыл бұрын

Most 2000s mx intro I’ve ever seen, love it

@dirtbikedave 2 жыл бұрын

I'm posting a link to this video in the comments of all other FCR carb videos, to help people find what they are looking for. Great job!

@CoteMotorcycles 2 жыл бұрын

Much Respect! Thanks for watching!

@WeekendWanderers4x4 9 жыл бұрын

This is an AMAZING video. Just what I needed :) Thanks!

@CoteMotorcycles 9 жыл бұрын

Glad you liked it. Thank you for the comment!

@chriselkamikaze20 8 жыл бұрын

Excellent video extremely informative step-by-step

@amityahav123 Жыл бұрын

Great video and easy explanation! Thanks a lot mate, carb service made easy this time!

@CoteMotorcycles Жыл бұрын

Thanks for watching brother!

@jordonmartin2937 6 жыл бұрын

Excellent video!

@austinmoon4690 4 жыл бұрын

By far best video out there thank you!

@CoteMotorcycles 4 жыл бұрын

Glad to help! Hit me with a like and share! Thanks for watching!

@azr2d1 2 жыл бұрын

FOr carb cleaning I use these tiny brushes you can buy on ebay. I spray carb clean into the tiny openings, then the tiny brushes. Then blow out with air. For stubborn dirt in the jets I use a brass string piece from a brush. Always hold the small openings against the light to see if they're clear. I've had the most stubborn dirt stuck in there. Oh and and don't look into the openings when you spray carb cleaner into them with the straw. Don't ask how I know. :-)

@zebrabiskupiec6869 8 жыл бұрын

Thanks from Poland

@tamagage2206 5 жыл бұрын

That's the best so far

@marcus-adrianbogstad4479 5 жыл бұрын

Thanks from Norway

@theredeemeriam Жыл бұрын

I am crying I didn't see your video first 😭 job well done!!!

@CoteMotorcycles Жыл бұрын

Appreciate the comment!!

@craftsmancollaborative 4 жыл бұрын

Greatly detailed video in only 10 minutes. solid visual before tearing into one.

@chevyswag3432 5 жыл бұрын

Man you just saved me!!!!!!!(crf450r carb cleaning)!!!!!!

@CoteMotorcycles 5 жыл бұрын

Chevy Swag glad to hear it!

@konsk8162 3 жыл бұрын

Thank you, your job is very good, including all the necessary details!!! Ευχαριστώ!!!

@CoteMotorcycles 3 жыл бұрын

Great to hear! Be sure to like and share the vids with your riding buds! Thanks for watching!

@konsk8162 3 жыл бұрын

@@CoteMotorcycles of course!

@joshuadieguez3897 7 жыл бұрын

Awesome vid

@85hj60 5 жыл бұрын

Thanks for making this video, I use JIS screwdrivers, if you want to have a firm grip on the screw use JIS, just read about it and try, never strip a japanese bolt again.

@anerloks 4 жыл бұрын

Very well made video. Thank you

@CoteMotorcycles 4 жыл бұрын

Thanks for watching! Please thumbs up and share!

@ronfrieborn2276 8 ай бұрын

Thank you for the video!!!😊

@CoteMotorcycles 8 ай бұрын

Thanks for watching!

@ElEtoo07 6 жыл бұрын

my head jet is broken, what can I do? thanks for video dude

@UncleSarkis 5 жыл бұрын

If you install the starter jet and the slow jet before the baffle spacing am I going to be wrong?

@dirtbikeenthusiast9494 3 жыл бұрын

Nice video very informative.

@CoteMotorcycles 3 жыл бұрын

Be sure to hit that thumbs up and share our vids with your friends!! Thanks for taking the time to leave a comment!

@alexandermjagi6126 8 жыл бұрын

Thanks from Estonia!!!!!!

@tomrogers3294 7 жыл бұрын

that was great, thanks

@saulllamas7912 7 жыл бұрын

8:52 the throttle chap is stuck up and I cant get it back down any tips? thanks

@dirtsharkmx3333 5 жыл бұрын

My bike cuts out and bogs at the top of each gear but runs fine cruising it want try to die just cuts out like it’s missing what could that be

@snapfly7 2 жыл бұрын

Do you know where I can buy a replacement accelerator pump nozzle?

@alex695215 7 жыл бұрын

in minute 3:17 when you say to remove the o ring prior to cleaning yours has something vooper looking in it well mine doesnt.. would i have to buy it to install it?

@llamascool4698 8 жыл бұрын

Will carb be a big problem for me? I'm buying a 450r carberated and I won't go off road. I'm only going to be driving it on the streets. (yes all dirt bikes are street legal in my country)

@CottonsH 7 жыл бұрын

my link arm is stuck :(

@glennfeldt2009 3 жыл бұрын

Thank you so much for this video 🙏🏻 Took a friends carb apart today and according to your video the diaphragm was installed the wrong way. Would this prevent the engine to start? 🇸🇪

@CoteMotorcycles 3 жыл бұрын

If you’re used to priming with the accelerator pump before start up then it likely would. If you usually just use the choke then it might not be your only issue. Glad you liked the video and thanks for watching! Be sure to hit the thumbs up button in the video and share it with your riding buddies!

@geraldlanz5838 3 жыл бұрын

Great video. I would add one more step before install I fill carb with fuel and test the accelerator pump. I had one not work right and had to pull carb again.

@CoteMotorcycles 3 жыл бұрын

Not a bad idea! Thanks for the comment!

@dixoncider7256 5 жыл бұрын

great intro.

@alex695215 7 жыл бұрын

would it be better to just buy a carburetor repair kit? with new jets and o rings?

@12475593 8 жыл бұрын

You forgot to check. The seal. Where the the throttle. Opens and closes. Cr top plate. Get the needle out and there should be a round seal. Look about for tear.

@joonasaartoala7471 7 жыл бұрын

does this work on a crf 150r

@joeydykstra6108 3 жыл бұрын

Thankyou

@haihao2648 6 жыл бұрын

Greattt !!!!

@Offyachestpodcast 8 жыл бұрын

Bravo👍

@Belicose777 7 жыл бұрын

My ap pump has no rivet on the diaphragm.

@madmechanix4962 4 жыл бұрын

Amazing video!! Question what if the accelerator pump jet has moved and is shooting into the air box? Ever seen that before?

@CoteMotorcycles 4 жыл бұрын

Never seen that before. I really have no clue how that would happen. Feel free to send me some pics on my Facebook page and I’ll answer any questions you have. Be sure to Like and share the vids!!! Thanks for watching!

@madmechanix4962 4 жыл бұрын

CoteMotorcycles Roger that!! I will see what it’s doing carb was just jetted for wrong elevation was super clean but that injector jet is puzzling..

@rfiskillingussoftly6568 6 жыл бұрын

Great video! ! Thanks! That o..ring and washer fell out ...didn't know how to reinstall. Awesome thanks! 😁

@triumpchop 8 жыл бұрын

Awesome video! I am about to have to do this as my CRF450x has developed idle fluctuation. Did you have to remove the shock to get the carb off? It doesn't look like it, but I didn't know if you had the top or bottom unbolted? Thanks again for the video, going to save me a lot of headache.

@CoteMotorcycles 8 жыл бұрын

The X is a bit bigger job. You have all the wiring/battery to deal with when removing the subframe. The shock will have to come out to pull the carb. If you're patient, you can try to loosen the carb boots, remove the subframe bolts and maneuver the carb so you can access the float bowl to blow the orifices and jets clear. It can be extremely frustrating and you have a higher probability of stripping the float bowl screws if they're tight. Good luck and thanks for watching!

@extremeenduro1560 8 жыл бұрын

+CoteMotorcycles Thanks for the info, I agree, shock needs to come out.

@Dalebrah69 8 жыл бұрын

I just removed my x carby by lifting the subframe up ...shock still bolted in

@PrecisionRifleGroup 4 жыл бұрын

Thanks very much!

@CoteMotorcycles 4 жыл бұрын

No worries!

@CoteMotorcycles 4 жыл бұрын

Thanks for watching! Please thumbs up and share!

@avocadoshoes Жыл бұрын

Nice video, I wonder if you know if a 2004 crf230f's carburetor will fit on a 2007 crf230F?

@CoteMotorcycles Жыл бұрын

You can go to bike bandit.com and compare the part numbers to know for sure. Very likely it will though.

@avocadoshoes Жыл бұрын

@@CoteMotorcycles Thanks!

@gunsntech411 9 жыл бұрын

I understand it can be adjusted without taking the carb fully out, but just to clarify... You can remove the jets all together without taking the carb out?

@CoteMotorcycles 9 жыл бұрын

You'll have to at least loosen the sub frame and pull the carb out of the boots to pull all of the jets. The pilot and the main can be removed by turning the carb sideways and pulling the float cap. Going to need a lot of patients though.

@twinculturevlogs 6 жыл бұрын

Do you know what would cause my crf150rb to boggout only when it's in low rpms?

@ZammianX 6 жыл бұрын

God's Child Loving Life idol is probably too low

@xplorer321 8 жыл бұрын

hi mate great videos! i have a 04 crf250 and it will not start from cold on the kickstart no matter what i do, if i bump it it will fire straight away! and when warm can get ti start after a few kicks with tiny throttle, would u say this is valves, piston or carb problems i have had the carb of and clreaned it and also have checked valve clearences

@followtheflip2172 8 жыл бұрын

+Rob bambrough I would love to hear his response. I have the same problem with my 04

@xplorer321 8 жыл бұрын

+FollowTheFlip i have found half the problem, my inlet valves were seriousley worn out so i replaced them put it all back together and thag slightley improved it startimg bit still terible! so i cleaned the carb and it was still the same! i took it to a shop amd they think its down to the ignition system (cdi, dodgy wire) so i am currentlt playing anout with that to see if i can find the issue

@xplorer321 8 жыл бұрын

+FollowTheFlip i recommend finding out the tolerance for crf2004 valve clearnces and if theyre tigt between the camshaft and valve bucket theyre gonna need replacing

@CoteMotorcycles 8 жыл бұрын

I would suspect the decompression clearance is off. Could be time for a piston/rings. Could still have a plugged pilot jet or air passage on the intake side of the carb. There are literally hundreds of reasons it may be acting up. Go through systematically with your manual and our videos to see if anything is out of the ordinary.

@theforester_ 8 жыл бұрын

thanks from brazil

@CoteMotorcycles 8 жыл бұрын

Glad you liked the video! Definitely need to do some riding in Brazil one day. Thanks for watching and please pass the videos on to your friends!

@CoteMotorcycles 8 жыл бұрын

Glad you liked the video! Definitely need to do some riding in Brazil one day. Thanks for watching and please pass the videos on to your friends!

@gabrielcardoso349 8 жыл бұрын

sabe a numeração dos gicles originais desse carburador? vai me ajudar muito man

@manuelbegazo5554 8 жыл бұрын

a question like do to adjust the carburetor air and gas few laps from the air is a crf 250 r 2008

@CoteMotorcycles 8 жыл бұрын

Sorry, that question doesn't make any sense to me.

@manuelbegazo5554 8 жыл бұрын

+CoteMotorcycles must carburar the bike with air and gasoline, because when I sped up so fast it sucks ?? in the video goes a bolt 2 turns you give that to serving

@theforester_ 4 жыл бұрын

hi mate i commented this vid probably 4 years ago, i'm from brazil and it helped me a lot even though i couldnt understand a word you were saying, but now 4 years further i'm quite more confident w the language. with that said my question is: when i'm riding the crf 09 and come close to a turn where i need to quick decelerate (kind like going to iddle speed) the carb take sometime to do that (not instantaneously as it should be), i have put like 4 or 5 ml of 2 stroke oil with the petrol it has gotten better but 100%... do you have any suggestions in how to fix this problem? thanks mate

@CoteMotorcycles 4 жыл бұрын

I wouldn’t put any oil in your 4 stroke. It changes the density of the fuel and will likely just foul your plug. 5ml in 6 L isn’t going to do much but there’s no reason for it. Sounds like you have a hanging idle. I would start by adjusting your air mixture screw. You probably have your idle set too high and the mixture screw set wrong which will make it run rougher at idle. Go buy one of those knob type adjustable mixture screws and put it in the carb. There’s a tiny spring, o ring and washer on those screws so be careful; the o ring will likely stay in the orifice and not come out with the other parts. Set it at 2.5 turns out and then warm the bike up. Once it’s warm, set the idle as low as it can go without stalling and start turning the screw until the rpm changes. See if you can adjust it to get the idle to go up. There will be 2 numbers of turns you’ll end up with. It may idle down at 4 turns and at 1 turn, everything in between will seem to run better. Set it in the middle at 2.5 turns. Your throttle should be super crisp and rev down no problem. That’s where I would start, there could be 20 different thing causing your issue but I can’t get into that on KZfaq comments!! Hit me with a like and share the vids if you like them!!

@theforester_ 4 жыл бұрын

Thanks very much mate for the answer I definitely gonna try this tips on the next weekend (i'll buy this quick air adjuster first cos mine is the original one) Thanks again and stay safe

@3SPCOD 4 жыл бұрын

Hey my 03 450r runs and idles ok,but when I pull the hot start it dies and im at the max turns of 3.5 out

@CoteMotorcycles 4 жыл бұрын

Hot start is used to start your bike when it’s hot. I would expect the engine to stall when the lever is pulled.

2 жыл бұрын

Is this applicable to a 2005 CRF250R? I have a carbureted 4 stroke

@CoteMotorcycles 2 жыл бұрын

Should be the same carb.

@geraldlanz5838 3 жыл бұрын

On 2005 CRF250X there is no way I can get carb will slip out the top like that. I removed head stay and still no room. I have to unhook throttle cables from twist and hot start cable and slide out left side.

@CoteMotorcycles 3 жыл бұрын

I think on the X you have to remove the sub frame and rear shock. Those are kind of a pain it the ass. Be super careful not to break the hot start seat! Really easy to break when working around the carb.

@pwndwner 8 жыл бұрын

how do you adjust float level the manual doesnt really explain that well should the carb be flat on its side or at an angle

@CoteMotorcycles 8 жыл бұрын

Carb should be upside down and level. Very rare that the float needs adjusting.

@dariusjones2345 8 жыл бұрын

+CoteMotorcycles will running rich cause over heating

@Austinkordell_ 8 жыл бұрын

could you explai how you did the second throttle cable you skipped past it and mine wont go on

@yeahwerepthesamesmartech7113 7 жыл бұрын

second throttle cable?

@123XxGILMORExX321 6 жыл бұрын

YeahWeRepTheSameSmartech lol just found this comment, gold

@aubreyroche5080 9 жыл бұрын

Is there a Vacuum Release Plate & Seal on this Carb ?

@CoteMotorcycles 9 жыл бұрын

Yes

@shaunpriest7351 9 жыл бұрын

I've got a CRF250X , it only starts with the choke on and I let it idle with the choke for about 1 minute , and when I put the choke off it just dies ? Any suggestiions what to do ?

@xplorer321 8 жыл бұрын

adjust the idle screw or mixture screw once it is up to running temperature

@mrboomlive807 8 жыл бұрын

If that doesn't work then you might need a bigger pilot jet.

@CoteMotorcycles 8 жыл бұрын

+Shaun Priest sorry for the extremely late reply. If it was idling good at one time and now it doesn't, you'll need to clean the pilot circuit. Thanks for watching!

@alexini5 9 жыл бұрын

Do you know how can i fix the "hanging idle" problem? I have that problem on my CRF 450R....If you know please help.

@CoteMotorcycles 9 жыл бұрын

Usually it's from having the mixture screw improperly adjusted or a plugged pilot circuit with the idle turned up to compensate. Clean the carb thoroughly with compressed air and get an aftermarket adjustable mixture screw. Otherwise, you may have an air leak somewhere. You can find a leak by spraying flammable brake clean over possible trouble spots. (such as an intake boot ect) the idle will fluctuate with the added fuel if there is a leak present. Have a fire extinguisher handy, just in case.

@sammielitherbury1801 7 жыл бұрын

alexini5 i have that bike and same freaking problem i took the hole carb apart and put it back together it worked perfecto

@This0is0pointless 5 жыл бұрын

@@sammielitherbury1801 check your valves

@sammielitherbury1801 5 жыл бұрын

@@This0is0pointless lol that commrnt was 2 years ago i have 2 new bikes now

@This0is0pointless 5 жыл бұрын

@@sammielitherbury1801 I didn't even notice that lol

@theforester_ 7 жыл бұрын

whats the name of parts that you remove on 5:24? (plastic white)

@Belicose777 7 жыл бұрын

Mauricio Freisleben baffle plate

@theforester_ 4 жыл бұрын

Whats that part for?

@trevorwebster7148 4 жыл бұрын

My slide is sticking after cleaning the upper part of the carb with carb cleaner (in video: 8:28) What can I do to get it sliding smoothly again?

@KingGoRealLa205 4 жыл бұрын

Dirt builds up under it an on the sides keeping it from closing all the way an hanging up. The rollers on the side will to if it has them. Hope this helps!

@CoteMotorcycles 3 жыл бұрын

Sorry for the late reply! If anyone else has this problem: make sure you didn't drop one of the needle washers into the slide area. There are also sometimes small lock washers for the slide caps to watch for. If there is none of that holding it up then take some brake clean to it until it runs smoothly. You can also lubricate it with WD40.

@ModelKing1000 8 жыл бұрын

What exactly are the TPS sensors for on these carbs?

@CoteMotorcycles 8 жыл бұрын

Throttle position sensor for the ecm to adjust ignition timing.

@ModelKing1000 8 жыл бұрын

+CoteMotorcycles That's what I thought but wasn't sure. lol Thanks man!

@stuballer 7 жыл бұрын

Joseph Ros

@glennfisher4011 9 жыл бұрын

Bike will stall out starting to move slowly or when I come to stop I know it's not my clutch skills so what is it you think ??

@CoteMotorcycles 9 жыл бұрын

If it's idling ok, I'd say it's a worn clutch basket not releasing the friction plates properly. If it's not idling well I'd say it's your pilot screw adjustment or plugged pilot circuit. I'd need way more info to diagnose it properly, hope that helps.

@CoteMotorcycles 9 жыл бұрын

You can try loosening the carb manifold clamps and carefully turn the carb sideways to access the float bowl. To clean the carb properly you should remove the carb, meaning removal of the subframe, tank and top shock mount. Keep in mind, contamination may be coming from the air filter and through the air jets or through the fuel tank. We have videos showing you exactly how to do all of that so it should be a piece of cake.

@CoteMotorcycles 9 жыл бұрын

Fuel, brake fluid and engine/trans oil change for sure. I would also change the air filter with a new one instead of cleaning it. Tires can crack over time and bearings can rust so check your wheel and steering bearings to be safe.

@CoteMotorcycles 9 жыл бұрын

I typically use twin air filters and maxima filter oil. I would stay away from k & n, they tend to let more debris through that doesn't help the intake valve issue on those bikes.

@CoteMotorcycles 9 жыл бұрын

Use air filter oil only. I like the tacky spray on oil, the pour on oil seems to seep out after a short time.

@sarahwunsch193 3 жыл бұрын

Do I empty my gas tank before removing??

@CoteMotorcycles 3 жыл бұрын

I don’t. Turn the fuel valve off and you should be good to go!

@2rztaco 3 жыл бұрын

Whats the hot start plunger for ?

@CoteMotorcycles 3 жыл бұрын

It lets more air into the fuel / air mixture for easier starting when the bike is hot.

@2rztaco 3 жыл бұрын

@@CoteMotorcycles thankx for replying 👍

@nenosuzuki1020 5 жыл бұрын

top brzil....

@gabrielcardoso349 8 жыл бұрын

Oi, sou do Brasil, você sabe a numeração dos gicles?

@CoteMotorcycles 8 жыл бұрын

Sorry...English is my only language.

@gabrielcardoso349 8 жыл бұрын

+CoteMotorcycles I have a carburetor of Crf 250, but do not know the number of orifices, use 48 low and 185 high, but what would be the next original factory?

@goboardcanada6263 8 жыл бұрын

+Gabriel Cardoso no way I could know that. You'll have to go to the dealership and see what they came with from the factory.

@gabrielcardoso349 8 жыл бұрын

+GoBoardCanada Nao tem um padrao de gicles em que todas vieram? Tenho muito que saber os que vieram originais de fabrica Editar

@alanair7019 6 жыл бұрын

Veddy goodentaken. Dunke.

@MikeHanby 8 жыл бұрын

What is the product you are using for the "parts cleaner" in the video?

@CoteMotorcycles 8 жыл бұрын

+Mike Hanby I use honda combustion chamber/carburetor cleaner. Seems to work the best out of all the products I've used, won't swell any rubber parts like other cleaners. After using carb cleaner you can use brake clean and compressed air as a final step.

@matthewh5439 8 жыл бұрын

+CoteMotorcycles Would brake cleaner swell rings?

@CoteMotorcycles 8 жыл бұрын

+Matthew H it really depends on the product you're using. Some manufactures use rubber safe formulas while others don't. Typically brake clean will dry(shrink) rubber and varsol/carb cleaner will make it swell.

@CoteMotorcycles 8 жыл бұрын

@matthewh5439 8 жыл бұрын

+CoteMotorcycles So I should try to get parts cleaner?

@maverick242 3 ай бұрын

The middle body needs to be clean as well. 4 orings there are really important

@CoteMotorcycles 3 ай бұрын

In my experience it’s best to leave the body assembled and only go into where fuel / debris can sit. I would only do an absolute tear down if the whole carb was soaked in some kind of solvent that might affect the o rings.

@maverick242 3 ай бұрын

@@CoteMotorcycles yesterday pulled a fcr from 2005 wr450. Needle bent, middle body gaskets 2005 ( factory used glue). Can't post the pictures. Was disgusting.

@Luke-jq5ke 5 жыл бұрын

My 230f is different 😔

@juanguerrero261 8 жыл бұрын

what if my carb doesn't want to shoot the gas at all

@yeahwerepthesamesmartech7113 7 жыл бұрын

might be accelator pump

@alicesworld6982 2 жыл бұрын

Hello father🤓

@CoteMotorcycles 2 жыл бұрын

Hahaha! Working on your motorcycle?

@ivanchomendo7879 2 жыл бұрын

Please enable subtitles in Spanish. Thank you

@DirtRacing118 8 жыл бұрын

Longest intro in the world

@generatewebdesign5900 3 жыл бұрын

So basically take it to the Honda dealership then.

@CoteMotorcycles 3 жыл бұрын

Hang on.....did I....? No. I didn’t say that at all! Get in there and clean your damn carb man!

@travisedwards725 5 ай бұрын

You didnt clean the mid body

@CoteMotorcycles 5 ай бұрын

This is all you usually need to clean unless the bike was kicked over in a ditch with the airbox off….definitely wouldn’t touch the tps. As long as the fuel / air passages are clear the rest of the carb can usually just be blown out with compressed air as there’s no fuel above the float bowl and there’s usually an air filter stopping dirt.

@richardtschida2321 5 жыл бұрын

I don't get it why wouldn't you clean the slide and the rest of the upper carburetor. Also no attention to the mid body???? Just not a very good or thorough cleaning.

@goboardcanada6263 5 жыл бұрын

There’s really no reason to disassemble anything more than is shown for cleaning purposes. Use parts cleaner and compressed air for the slide and slide linkage. You’ll typically only gain regret and remorse if you pull the TP sensor or slide to clean the mid body. The slide can go in either way and it’ll drive you crazy when you can’t figure out why the bike runs like crap after a fresh carb clean.

@richardtschida2321 5 жыл бұрын

@@goboardcanada6263 I beg to differ with you sir l just completed a cleaning of an fcr39mm and the upper segment with the slide and its mechanisms were the dirtiest part of the carb. There are instructions on how to install the slide and there is no need to mess w/tps.

@markmagness3693 8 жыл бұрын

And then there's fuel injection!!!

@markmagness3693 8 жыл бұрын

👌😍😭 the crying is because mine is carbureted

@prlandry 8 жыл бұрын

+Mark Magness much cheaper to change or clean jets in a carburetor versus changing a fuel pump or an injector

@caleb6032 8 жыл бұрын

Intro is way to fucking long

@CoteMotorcycles 8 жыл бұрын

These are the comments that really make the countless hours of filming and editing worth while. I apologize for the 30 seconds of your life you'll never get back. But then again, it's my name on the video soo......

@yourface3154 8 жыл бұрын

+SIRplsDNT That chick is banging, wtf are you talking about? Lol!