hey my landing gear does not work

@@gamingfr1728 I would recommend that you go to the controlls options and select in the upper left the option "search by input" and see which function is assigned to the landing gear lever. make sure that the correct function is assigned. otherwise try to update the firmware of the throttle quadrant. Tell me if it helped. :)

how to do firmware update

@@CharlesIvansfather you need to go to the thrustmaster.com website and download the updater in the download section of the TCA Quadrant. Then open it and do the Firmware update

how do you do a hardware calibration and I have already done a firmware update adn it still ahsnt worked

you're very welcome 🙂

I‘m glad that it helped! Thank you for your feedback 😊

Many thanks!

gerne ;)

welcome! Glad that it helped

you're very welcome

You are very welcome 😊👍

glad it helped

I'm glad that you liked it and that it was helpfull. Interesting that you don't have to reverse the axes for the spoilers. But.. in the end it's not important. If it works it is good. :)

danke für dein Feedback. Mit den Spoilern kann ich mir nur vorstellen, dass das Häkchen bei "umkehren" gesetzt oder eben nicht gesetzt ist. Da kannst Du mal nach der Spoiler-Belegung suchen, in dem du auf der Konfigurationsseite vom TCA Quadranten auf "search by input" bzw. "nach Eingabe suchen" (meine das heißt so). Und dann mal schauen, ob da ein Haken bei umkehren gesetzt oder nicht gesetzt ist. Quasi das Gegenteil von der jetzigen Einstellung wählen und dann müsste es klappen.

Very strange. Do you use the PC only Thrustmaster Quadrant or the (new) PC/Xbox Version?

@@SNUGaming wot wot wot ??? I can not believe it . after days of following your tutorial to the letter, yesterday I turned off the PC and went crazy, I turn it back on this morning and the throttle quadrant works perfectly. I don't know what to say, the mysteries of computer science or there are ghosts in the house

@@zaro9709 I'm glad to hear that it finally worked out! Have a lot of fun with the fenix and your TM quadrant. :)

Hey @edwinsoto7233 First of all, a few dots and commas would have helped to read your text better. 😁But I think that I understood your problem. This is the first time that someone describes these issues. But (!) whenever you do changes in the controlls options you have to do the calibration in the MCDU again. My recommendations: - go back to the MCDU Config and press the delete configuration button. So you'll have a fresh start and can try it again. (This should help) - do the firmware update via the Thrustmaster Firmware Update Software (can be found on thrustmasters webpage) - if this won't help maybe try another USB Port. What kind of USB Port do you use? USB 2.0, 3.0? (I don't know if it makes a difference) - try using another axis. Some users wrote that the throttle axis 1 and 2 didn't work for them. Instead they used the standard axes (Throttle Axis 0 to 100%) and it worked fine. If this solved your problem it would be nice if you can give me a little feedback. Because other ppl may have the same issues. Thanks

To be honest.. I don’t have a clue. Do you use the current firmware and have you tried the hardware calibration (not in the MSFS, but in the thrustmaster software)? Maybe that helps.

Good question. I assume yes. But I don’t own it. That’s why I can’t provide a sufficient answer to this. Sorry. Have you tried the same procedure as with the airbus quadrant?

Hey.. unfortunately I don’t have the flight hotas x.

@@SNUGaming oh its ok!

So you completed the calibration and saved it and after you go to the main menu and back to the cockpit the thrustlever is stuck on to/ga? Some ideas to solve it: - change the “reverse axis” - maybe you have to take the standard axes (see my pinned comment up front) - make sure that you’ve installed the latest firmware and drivers - delete the configuration in the MCDU and do the configuration again. - remember. Whenever you change something within the sensitivity or sth else in the TCA Quadrant you have to do the configuration in the MCDU again. Hope it helps

well, in the video I do say to use throttle 1 and 2 axis instead of throttle 1 (0 to 100%), don't I? at the time I produced the video this was the proper solution to set it up. Due to firmware and software updates it may have changed for some users. That's why I wrote down in the pinned comment, that for some users it might be suitable to use the 0-100% option instead.. :)

@@SNUGaming fair comment

I would recommend to use the TM firmware Updater to do it. Very simple: support.thrustmaster.com/de/product/tca-quadrant-airbus-edition-de/ Let me know if that helped and solved your issue with the controls

@@SNUGaming how do i do it

Hi.. no, unfortunately not. I assume you selected the correct axes in the controls options. Maybe you should try it one more time with the configuration in the MCDU. As I tried it the first time I had the same problem as you. Did everything correctly but the levers wouldn’t move. Did it again and after another try it worked. Besides that: try to update your firmware. Maybe that helps as well?!

I'd recommend to check the USB ports. Maybe it is an issue with them. Also you could download the drivers package. support.thrustmaster.com/en/product/tca-quadrant-airbus-edition-en/ there also is an app called "Thrustmaster Flight Control Panel".. or maybe in your system settings for game controllers as well.. If the doesn't move at all it could realy be a problem with the USB Ports or the device itself. If it moves but doesn't show up in MSFS I would go to one of the MSFS community boards and ask the question there again.

Do you have a conversion for the controls? I play on Xbox… everything updated but since last update the quadrant doesn’t seem to work as it should. It works just a bit .@@SNUGaming

Same problem… halos hard to say what button x and y is

hey.. sorry to hear about that issue. I'm not quite sure how to solve this problem. I would recommend to do the firmware update of the throttles. You'll find the driver at the thrustmaster website. Also try to do the hardware calibration (not in the MSFS). If you don't know how to do that. There are videos on youtube. I didn't do my own "how to do" video concerning the hardware calibration yet. Additionally you can try to use different axes in the controls settings options. See my pinned message. Hope it helps.

santiago did you fix this issue? i am facing the same problem it's soooo frustrating

were you able to solve your issue?

Have you tried the hardware calibration (not in the Sim) and did you do the firmware update?

what does it show instead? have you tried the hardware calibration of the throttle (not in the simulator) first?

@Flight Voyage Hi I have the same issue, I contacted the FenixSim support but obviously have to wait for a response. If they can help I'll let you know.

@@Mauriceweller interesting. It seems like that this issue occurs more often in the last weeks. If they replay please post the solution to the issue here. 😎👍

I got the email and in the end it was quite obvious. Go to >options>controls options>assign the levers to throttle axis 1 and 2. Make sure it says throttle axis and not throttle axis (0-100%). I hope it can help.

@@Mauriceweller thx 4 the answer. Interesting. For me (and a lot of other ppl it works with throttle axis 1 to 100%) I have to check that myself, but I hadn’t any issues (as you can see in the video)

First I had the same issue. Than I checked again if I took the correct axes. Did a mistake there. Make sure you use "Throttle 1 Axis (0 to 100)" and "Throttle 2 Axis (0 to 100). If that doesn't work try updating the firmware of the quadrant or to the hardware calibration of the throttle. hope this helps

Some users wrote that the throttle axis 1 and 2 didn't work for them. Instead they used the standard axes (Throttle 1 and 2 Axis 0 to 100%) and it worked fine.

I would check if your firmware is updated to the newest version and do the hard ware calibration on the throttle itself. (Not in the MSFS). Download the software from the thrustmaster.com website

@@SNUGaming ok, thanks, when I try that I give you an answer

@@SNUGaming but for exemple when i use FBW a320neo didnt hapend that

@@ytnighthpower1932 maybe you have to use different axes for the Fenix A320. For some users for some reasons it is different than in my video

@@SNUGaming ok do u know how can i resolve it or is by the way that u tell me by official site of thurstmaster?

Regarding the reverse thrust I would recommend to leave a little gap in the settings. Means idle reverse should be set closer to full reverse instead of closer to idle. Then it shouldn’t be activated unintentionally if you set your thrust lever to idle.

Alright, thanks! Once I get that done I just gotta do the buttons.@@SNUGaming

Question: do you have a tutorial on the buttons lol? can't seem to figure them out@@SNUGaming

@@Loaf_ve unfortunately Not. I only can recommend to use the standard setup of the TCA Q-Eng first and to duplicate it. (As shown in the video) So you will have all the standard buttons set up correctly and only have to do the changes as shown in the video for the levers.

My controls were somehow wiped when I installed the add-ons. I am pretty sure that even removing the add-ons, saving it, and then re-installing them wouldn't work.@@SNUGaming

then I would reccomend doing the hardware calibration (need to do a video about it because so many ppl asked how to do it).. Maybe I can create one in the next couple of days.. otherwise search for thrustmaster airbus quadrant calibration or sth like this. there are a couple of videos out there which explain how to do it.

@@SNUGaming thanks bro if you can upload a video that will really help but ill do what u said first

Sorry to hear. This video is for PC users. Don’t know how it works on Xbox. But should be similar?! Sorry that I can’t help

@@SNUGamingall good

what exactly is the issue? Have you tried updating the firmware and software of the TM quadrant?

I kept trying and got it to work, many hours went into that lol

Try a Firmware Update ?!

I found the flaps not working after the last update too. Did the configuration as shown at the end of the video and now it works again

@@SNUGaming sorry i missed that,was trying to looking on my side monitor and do setting same time ,did not move the screen to my 55 inch in my cockpit ,managed to get it working .thanks for reply

sorry to hear that. I guess you've tried all the troubleshooting?! Update Firmware, do hardware calibration (not in msfs), ensure to select the correct axes, software update if possible.

Sorry to hear that. Have you selected the correct Axes ( 1:34 ) and have you performed the calibration in the MCDU (4:14) correctly? Otherwise I'd recommend to update the firmware of the quadrant and to do the hardware calibration of the quadrant itself. I hope it helps!

what exactly?

where exactly?

is there a new version? I've to check that

@@SNUGaming that would be awesome! Thank you!

@@mcshiggitypilot5901 to make it more clear for me. with the new firmware version the configuration of the quadrant doesn’t work like in my video?

Well mate.. showing the finger is not very nice. This is a 21:9 screen with a 3440x1440 resolution. Maybe that is the reason why you can’t read it well. But just listen to the voiceover. Very easy to understand what you should do. Or watch it on a different device like your cell. You even can zoom in there

I am surprised not only a poor videographer but also a pompous ass ! You and your fancy graphics can EAT SHIT 🖕🖕🖕!

@@SNUGaming dont listen to this guy, hes just a hater

@@moejaime2654 Someone's jealous. 😂

@@Rowan66109FART FART AND A DART !!! LOL !!

check your installation and make sure that you chose fenix a320 in the world map menu

?

Why when I press mcdu , it doesn't go to that menu ? It does nothing

@@bengvideos572 sounds like the Microsoft standard A320 if the MCDU has no functionality. Do you see the iPads on the left and right in the cockpit? Perhaps the selection of the A320 was not saved or transferred correctly?