How to connect rear Emergency Brake cable

How to connect rear Emergency Brake cable - Ford Ranger

Рет қаралды 50,748

5 жыл бұрын

This may be helpful if you need to replace your rear Emergency Brake cables due to being rusted or frayed. Or if you swap in a junkyard axle with clipped E-Brake lines.
Thanks for watching.

Пікірлер: 24

@AtlanticDrain 3 ай бұрын

JWD!- just had a viewer ask me how to install a new emergency brake cable. Your video fits the bill. Thumbs up!

@ianhards2476 2 жыл бұрын

Thank you for posting this. Had to replace my parking brake cable today and this massively cut down how long I took to do it. Cheers

@troynewman4383 4 жыл бұрын

You saved me hours of trying to figure this out. Huge thanks!!!

@Box545x39 4 жыл бұрын

That's great, glad I could help with the vid.

@000001willy 3 жыл бұрын

Excellent video. The video work was excellent as were the step-by-step instructions.

@perjian1697 2 жыл бұрын

What are the chances someone actually had to do this!? LoL. Perfect!! Thank you!! Swapped a rear end on my ranger but the cables were damaged so didn't put them in. Got new ones and about to do this and was wondering how to get in there easily without a complete teardown. LoL

@depatadeperro8955 3 жыл бұрын

Today 01/17/21 was replaced, drums, rotors, pads , rear and front and sock absorbers, front and rear, on my 1995 ford ranger, spend around $ 500 dlls, my wife was real mad cause she says its an old truck to spend that money, but......I LOVE MY OLD FORD RANGER. #rangerlover4ever

@Walshslandscaping 2 жыл бұрын

thanks for the tips and tricks

@joshcormier5958 3 жыл бұрын

Doing this today thanks for the tips and tricks!

@Gotdurt 4 жыл бұрын

How did you relieve the tension on the parking brake cable in order to push that spring back with the vise grips? I can't budge it, the spring is too strong... Would have assumed that there would be a barrel adjuster somewhere before the cable Y-split, but nothing I can find.

@Box545x39 4 жыл бұрын

Aside from making sure the e-brake isn't engaged, I didn't relieve any other slack. I used two vice grips, one on the end of the cable to pull and another seen in the vid to push the spring up the cable and clamp it off. It's not easy but the spring will compress enough to get you some slack if you pull the end of the cable and push the spring at the same time. Hope you get it done.

@knottreel 3 жыл бұрын

I'm having the same problem with my 91 ranger passenger side. The cable won't budge out of that coiled sleeve. The left side was no problem, but just too tight with the right side.

@kohlitheconqueror315 2 жыл бұрын

Dude I can just kiss you right now! Lol y Thank you sooo much

@MAGWolf 3 жыл бұрын

Still stuck on the remove your drum part lol. Thing is rusted on for me.

@Box545x39 3 жыл бұрын

Bummer. You could try loosening the starwheel adjuster on the rear brake cylinder (I believe counter clockwise while facing the rear of the truck will loosen it) then give the drum some whacks around the face with a big old hammer and it should break free easier. The starwheel can be a pain to click, I use a bent Flathead Screwdriver.

@pocketdiy 4 жыл бұрын

question is why did your disconnect? poor design i think on the retainer.

@Box545x39 4 жыл бұрын

I swapped a different axle into that truck. I agree, if you're talking about the plastic push in clips.

@pocketdiy 4 жыл бұрын

@@Box545x39 no the metal arm that has a groove cut in flr the cable to slide into the spring on the cable seems to hold it from falling back out.

@knottreel 3 жыл бұрын

You skipped the hard part. How the hell did you pull that cable out far enough to attach your second vice grip?

@Box545x39 3 жыл бұрын

Pinch the end of the cable with a vice grip or pliers, then I used the jaws of a second vice grip to slide up the cable (which compresses the spring in the same motion) and pinched the cable once I had enough exposed. Hope that helps.

@knottreel 3 жыл бұрын

@@Box545x39 Thanks so much for the response. I finally got it connected. The problem I was having was that the cable was so tight that I couldn't slide it up. I used your advice with the vice grips. I made one change so I could get more leverage. One vise grip held the end of the cable and the other held that vice grip against the backing plate of the wheel. With my freed hand , I could use bent needle nose pliers as a lever to pull the cable out. With the other hand I could slip the brake arm over the cable. I really appreciate your help.

@Box545x39 3 жыл бұрын

@@knottreel No problem, glad you got it sorted. It's an easy job on paper, but once you get in there it's tricky to get everything to cooperate, lol.

@577buttfan 2 жыл бұрын

Thats how he ripped his gloves to shreads lol :)