How to Replace Rear Drum Brakes 95-09 Ford Ranger
Рет қаралды 452,155
Buy Now!
New Brake Shoes from 1AAuto.com 1aau.to/ia/1ABPS03290
BUY THE PART:
CLICK "SHOW MORE" TO SEE INSTRUCTIONS BELOW:
1A Auto shows you how to repair, install, fix, change or replace your own worn, squeaky, fading old brakes. This video is applicable to the 95, 96, 97, 98, 99, 00, 01, 02, 03, 04, 05, 06, 07, 08, 09 Ford Ranger
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oatD/1AXAA00013
• 19mm Socket 1aau.to/oJy/1AXAA00043
• 1/2 Inch Breaker Bar 1aau.to/oke/1AXAA00078
• Ratchet 1aau.to/oaB4/1AXAA00016
• Torque Wrench 1aau.to/oXs/1AXAA00044
• Brake Parts Cleaner
• Floor Jack 1aau.to/oCt/1AXAA00068
• Jack Stands 1aau.to/oAn/1AXAA00065
Subscribe: / @1aauto
Check out our playlist:
Ford Ranger 1998-2012 3rd Gen: • Ford Ranger 1998-2011 ...
Ford Auto Repair Videos: • Ford Auto Repair Videos
For More Info visit us at 1aau.to/h/aVY/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
@1AAuto 3 жыл бұрын
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@norbertrivera 3 жыл бұрын
100 pounds in each lug nuts?
@JL-tu9mf 3 жыл бұрын
B.
@calumrife 2 жыл бұрын
I can not tell you how valuable your tutorials are to me. I'm heavily invested into a Ranger and need all the info I can get. Thanks so much.
@mathewm7136 5 жыл бұрын
Couple of easy hints; 1. Every three oil changes, check and adjust the rear brakes if needed. Front brakes (pads) will wear out twice as fast if the rear brakes are not adjusted properly. 2. Once the drum is off and the springs are cleaned, take a pic for reference as well. As one side may have the e-brake hardware, the left/right sides may not be mirror images. 3. Another method - on the floor, lay out the new shoes & springs on top of each other exactly as they are to be assembled before tearing down the old parts. Take a pic of that too (hey, pics are free if you have the right phone). Plus, it'll give you an idea of what pieces you need to save vs discard. (It might save you the problem of digging thru the garbage can later!) 4. If you are not replacing the drums, you MUST have them re-surfaced when replacing the shoes. 5. Good habit is to buy the Combi Kit with new shoes. 6. Hold the two brake shoes together side by side. The shoe with the longer amount of ceramic/semi-metallic padding goes towards the REAR of the vehicle. 7. Never touch the inside of the drum (where it meets the pads) as skin oil & dirty fingers will reduce the braking power until it's burned off. If you, just clean it with brake cleaner. 8. You can put some lithium grease on the wheel studs when placing the lugs. It might save you (or a family member)from breaking your/their back while on a roadside sometime later. Good Luck!
@1AAuto 5 жыл бұрын
Thank you for all the tips and suggestions! We appreciate it! +Spaz 360
@joekoch1871 2 жыл бұрын
Fantastic video. No blah, blah talk. All business video, clear, smooth, good video clips, very informative, awsome.
@kevinmullen8180 Жыл бұрын
Thank you so much for this video, I followed it step-by-step and did the job myself. One tip, when it comes to replacing the lower spring, better to put that in partly before you attach the cable. I found trying to get it in the after the cable was pretty brutal on the spring. Thanks again, outstanding job! Why any auto manufacturer is still using drum brakes in 2004 is a mystery to me.
@chri5wyd367 Жыл бұрын
I just learned that I will be selling my 98' Ranger ASAP when Im done with these damn brakes.
@tehse7en Жыл бұрын
This video was extremely helpful. I just replaced both rear drum brakes on my '04 Ranger 4.0L - huge help, thank you!
@jefferymayhann312 6 жыл бұрын
So helpful!... I was not actually changing my brakes, but the emergency brake cable (it broke). But, to get to it, I had to take the brakes off, just like I was replacing them. When I got the drum off, the brakes were like new (I bought it used a few months ago), so I did not need to replace them. But, once I took them apart to replace the broken e-brake cable... your instructions on putting it all back together was a God send. By the way, I bought the brake cable from you guys... it was excellent quality and shipped very quickly.
@1AAuto 6 жыл бұрын
+Jeffery Mayhann Thank you for your order. If you would like to leave us a review on Google it would be greatly appreciated. Here is a link to our reviews section. Have a great day! goo.gl/i5JFNY
@bradforddrake8633 3 жыл бұрын
The Ford Ranger with 9 inch drums have no clothespin plungers coming out of wheel cylinder. The shoes have a metal shape that inserts into wheel cylinder. The emergency brake lever has a hook that connects it to the rear shoe. The Ranger 10 inch drums have the traditional clothespin plungers which push against the brake shoes and a bolt on emergency brake lever which is secured to front side of rear shoe with a C clamp.
@Madasin_Paine Жыл бұрын
A most rare tip. This may also help with Rangers 2001-09 All 4x4's All SuperCabs All w/Payload Package 2 upgrade All 2001~2005 Edge All 2006~2009 Sport 9" drums should have been factory equipment only on XL/XLT REGULAR cab 4x2's with the STANDARD Payload Package 1.
@moustachemike7128 5 жыл бұрын
I read this in my how to book some where: On removing and installing the e-brake cable to the brake shoe lever: pull on the cable from under the cab and put an allen or screwdriver in the foot brake retainer under the dash.... to keep the cable slack..just revers when done easy peeezeee.. no fighting the spring..
@MrTjthegreat1 2 жыл бұрын
Thank you! I was contemplating actuating the foot pedal but wasnt sure how to keep it open.
@WeezerPete 4 жыл бұрын
Thanks for the video! Helped me save some money!
@americanpatriot2033 9 ай бұрын
Thank you very much for your video I found it very useful. My brake issues are now solved and I can't thank you enough.
@gerryvillemaire1635 2 жыл бұрын
thank you, very grateful for this helpful video
@michaeljohn8905 3 жыл бұрын
These guys rock ! Thank you !
@1AAuto 3 жыл бұрын
+Michael John Thanks for checking us out! 1AAuto.com
@FBLM1969 6 ай бұрын
After a couple hours i changed the brake shoes. The only thing I hate more than drum brakes is paying someone to change them for me.
@Madasin_Paine Жыл бұрын
Couple tips picked up from other vid sources. Before removing drum cover, block tires to press rolling, if necessary, and release parking brake . There is a inch size rubber plug on the bottom back side of the drum cover and when removed, one can lessen the brake grip and make it easier to remove the front cover at the beginning. One can adjust the brake using this same technique but in the opposite rotation. The wheel can turn freely and the hear slightest sound of contact friction when ready. Then bleed that break line to this brake. When all is through, and the truck is ready to drive backing up should self adjust parking brake.
@ronvonbargen8411 4 жыл бұрын
When assembling the top spring your brake spring pliers should have a channel /groove in the handle hook spring on plier handle then place the groove /channel over the spring pin. Pry theHandel and the spring slides down the Handel onto the pin. Otherwise Great vid.
@richardbarkley9909 7 жыл бұрын
GREAT video! Thanks!
@1AAuto 7 жыл бұрын
+Richard Barkley Thanks for watching. We carry the brake shoes shown in this video on our website. Here's a link to them if any of our viewers needs to perform this repair. www.1aauto.com/brake-shoes/i/1abps00882?KZfaq&RV1uz62DFc&KZfaq&CTA%20Comment&ATony
@gusswalker 3 жыл бұрын
Great video and nice done!
@nonstop8888 Жыл бұрын
Well I have 2004 ranger well i had 2 strokes and The driver side rear brakes separated from the shoe passenger side wheel cylinder was leaking I was able to change the cylinder I was a mess well I’m gonna have to passenger-side complete that easy video help me considerably I’ve done quite a few break jobs in my day not a stroke victim it will take me all day tomorrow So Thanks for the info Gary in western ma.
@claudew5582 2 жыл бұрын
Thank you, this video help me immensely.
@1AAuto 2 жыл бұрын
+Claude W Thanks for the feedback!
@StonnieDennis 7 жыл бұрын
Thank you!
@1AAuto 7 жыл бұрын
+Stonnie Dennis Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/brake-shoes/i/1abps00882?KZfaq&CTA+Comment&RV1uz62DFc
@TIG2MAN0 4 жыл бұрын
awesome video
@gertis7420 6 жыл бұрын
Like always, great video.
@1AAuto 6 жыл бұрын
Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them; www.1aauto.com/brake-shoes/i/1abps00882?KZfaq&RV1uz62DFc
@johnjude2685 3 жыл бұрын
Because every thing so dirty , For as a illustration start with the replacement parts as you had in the finish drum as the color of the new clean parts shows up so much clearer for the student such as myself. But this is not a complaint but sujest for a better picture for what I am trying to comprehend. Thanks for the teaching, Your videos are always very helpful.
@Jacey2001 Жыл бұрын
thanks for the refresher!!! perfectly done. nice and quick... problem is.. I wont be nice n quick lol
@user-wr5lm8ke4z Жыл бұрын
Great work 1A Auto this video saved my truck! FIVE*****STAR*****REVIEW from me!
@crystincrowder7562 4 ай бұрын
Thanks for the video! I work at an auto parts store so I won't be buying from A1 Auto parts. But thanks!
@devildog310nc 4 жыл бұрын
You should make sure star wheel adjuster is easy to turn and you must adjust it to smallest setting when installing new shoes. No need to manually adjust
@matthewbishop4922 7 жыл бұрын
I wish y'all could make some vids about 95 4×4 rangers. the res nothing on KZfaq about hubs or clutch ECT.
@tomstrickland6002 4 жыл бұрын
Our 1995 Ford pickup had a different adjuster set up. Your set up is much easier.
@1AAuto 4 жыл бұрын
+Tom Strickland Thanks for checking us out and taking the time to comment. 1aauto.com
@TStheDeplorable 4 ай бұрын
Ford put out a Technical Service Bulletin on the brake drums locking up on 2002 - 2009 Rangers. The problem was worst after the truck sat for a few hours, and the drum brakes would lock when you hit the brake the first few times after sitting. Their solution was to install new shoes, and then use silicone sealer on the BACK side of the backing plate, putting beads around where the axle passes through the backing plate, around wheel cylinder, over and around the heads of the "nails" that hold the cups and springs, around the rubber brake adjuster access plug, and around the point where the parking brake cable enters through the backing plate. It seems that moisture gets in and causes problems, so I am also using anti-seize where any parts need to move against each other. Hopefully that fixes this annoying problem.
@scottguthrie8074 Ай бұрын
"...and then your remove the kidneys, while tapping the lower spring twince while using the break tool to simply attached to the cap forward and then simply close and sew up the patient on the other side. Allow two weeks to cure and take it to a shop if symptoms persist!!"
@thejamesasher 3 жыл бұрын
why oh why couldnt my truck have all disc brakes wa wa wa
@1AAuto 3 жыл бұрын
+James Asher Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@mentallyderanged9169 4 жыл бұрын
Nice video BUT you FORGOT to show people to add grease to the contact points. You put a small amount of grease on the 4-6 little nipples or those little high points on the backing plate. This allows the shoes to slide and have a nice lubricant to move easy vs metal on metal. Everything else is done very nice and easy to fallow, just picked up a 98 ranger and was seeing what I am about to get into I have done MANY and HATE doing drum brakes. 96 Chevy have been the WORSE for me lol.
@1AAuto 4 жыл бұрын
+Mentally Deranged 916 Thanks for the feedback and for watching!
@pizzaholic 5 жыл бұрын
Excellent video, I just wish my drums came off as easily lol.
@oobaka1967 3 жыл бұрын
It took my father and me 2 hours to get one drum off using prybars, steel wedges and a 5 pound sledgehammer. Had to cut the pins off from the back.
@akaychi 2 жыл бұрын
@oobaka1967 and everyone else: If your drum is tight, theres an access port behind the backing plate that looks right into your adjuster. Reach in and tighten up the adjuster with a flathead to close the gap and your drums fly right off!
@vapingwithhoffman5775 6 жыл бұрын
what do you mean by the adjustment can be done from the rear but you do it from the front? and dont they adjust thereself? auto adjust?
@Papascoffs Жыл бұрын
Ah until I bought a Ranger, I never realized how many smaller parts drum brakes had! Thank you for this!
@1AAuto Жыл бұрын
+Jesse Hunley Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@nickm6566 6 жыл бұрын
did the guy in the video go to uti in norwood ma? he looks wicked familiar
@perrymoffat5368 11 күн бұрын
Thanks!
@moustachemike7128 5 жыл бұрын
here is some more food for thought...some times when ya disturb the wheel cylinder for some reason or another they tend to leak,,why ? who knows..so while your already into it go ahead and replace them. and bleed the brake line with new fluid ..
@theobserver9131 4 жыл бұрын
Yep, sure enough. I replaced the shoes and all the springs and hardware, and bingo the slave cylinder started leaking. Now I'm going to have to at least halfway take it all apart to put a new slave cylinder in. Oh well. So goes life.
@1AAuto 4 жыл бұрын
+Old man Thanks for checking us out!
@joshsteele8293 2 жыл бұрын
The hard part is finding the lines I can’t even find them anywhere
@Louie12673 4 жыл бұрын
Does the adjuster have to be repositioned in any way?
@iqbalsingh827 3 жыл бұрын
I changed my break shoes for Ford Ranger 2009 as you showed in video, when I ran the truck it, it has horizontal lines on break shoes, what caused those horizontal lines, Please help
@originalcharacter3575 3 жыл бұрын
In regard to the emergency break wire I’m not sure if it’s been said, shown, or anything but my mentor taught me that if you pull directly out on the end “cap” if you will, it will give me you slack I between the spring and the end cap shows while he is attaching the components
@1AAuto 3 жыл бұрын
+Original Character Thanks for the tip!
@coreyroberts2831 4 жыл бұрын
If you have problems removing the drum, remove the rubber plug from the back side of the plate, use a flat head screw driver or self adjuster tool to back the self adjuster off. Drum should come right off... may need a helpful tap with a hammer as well.
@1AAuto 4 жыл бұрын
+Schweddy Thank you for the tips and for watching!
@gunfisher4661 Жыл бұрын
Also if your adjuster does`nt want to work take a propane torch and heat the drum in between the lugs many times it will just pop with out the use of a hammer after wards.
@yvesl.diasso9805 3 жыл бұрын
where did you get that needle noise tool from?
@Snowmunkee 4 жыл бұрын
Is there another video for replacing the wheel cylinders that are included in the kit?
@1AAuto 4 жыл бұрын
MoLottes Check out our library for more videos. 1aau.to/m/video-library
@timschmidt3784 2 жыл бұрын
I don't think the auto manufacturers could have come up with a more complex design for stopping a vehicle than drum brakes. Toyota used them on the back axle of the Corolla for years, long after other manufacturers converted to disc. You would think that discs would be more cost effective parts wise plus the labor associated with assembly.
@lobsterbark Жыл бұрын
Drum brakes last way longer between services if they aren't used too much. Thats why they make sense to use for the rear on a truck, most of the weight is up front and rear brakes aren't used as much anyways, so drums are way less maintenance than discs when used on the rear. Disks are have more surfaces that need to seal and interact with fluid. Getting good seals that last is one of the harder things to do when manufacturing anything. They have gotten good enough at it nowadays that drums are almost entirely obsolete, but this was not the case not that long ago.
@tadair705 3 жыл бұрын
So, just FYI, there's no need to remove the e-brake actuator on a 1996. It doesn't require a spring washer or horseshoe clip. It can be left on.
@1AAuto 3 жыл бұрын
+Tony Adair Thanks for the tip!
@markbonneville5402 2 жыл бұрын
Ya dont have to take it off my 01 is the same dont need them just put it in the hole lol
@TheLastPirate1973 Ай бұрын
which kit would I need for a 2003 Ford Ranger Edge 3.0? Can you post the link?
@IntheBlood67 Жыл бұрын
Great tips! Outstanding!
@royquesada5295 4 жыл бұрын
Wish you would of shown the difference in length of pads and on which side they go on. So many people do not even notice the difference in the pad size yet alone if it goes to the back or front.
@1AAuto 4 жыл бұрын
+Roy Quesada Thanks for the feedback!
@kelvinmann1058 Жыл бұрын
Long shoe to the rear.
@johnjude2685 3 жыл бұрын
Looks helpful. Because every thing dirty and faded ,
@alexandermancilla5291 Жыл бұрын
Does anyone know the size of drums and shoes for a 2004 ranger 4 wheel drive?
@Agent-vj3ns Жыл бұрын
Why don't you use the dedicated spring installer on the handle of your shoe pliers? 11:45
@253chiefin1 4 жыл бұрын
I watched this video to the 5 minute mark and realized the tools he uses made me give up hope i can fix my brakes. I tried another video and when they actually used pliers to undo the springs i felt way more in tune with that method. Using specialty tools on simple jobs make the job look way harder. This video intimidated me and made the job look difficult. This is my 4th ford ranger video and this guy is a good mechanic hell hes a great mechanic but sometimes i get confused when he uses complicated tools to do simple things. When he pulled out the spring tool i googled conversion kits to disc brakes. Once i saw the price i found another video that used the simple methods to do it and it was exactly what i needed to see.
@1AAuto 4 жыл бұрын
+Drivin Mopar Thank you for checking us out! We appreciate your feedback and will consider showing the specialty tools and then the alternative if you either do not have or cannot gain access to those specialized tools. We try to make our videos for the greatest audience and have since moved towards a more generalized way of repair rather than using all specialty tools when available.
@mikej.2803 4 жыл бұрын
The tools mentioned are very inexpensive you should purchase them. They are part of any persons tool kit who does their own Automotive repairs. Although I wish every manufacturer would go to disc brakes , and for the most part they are, because they are so much easier to repair and or replace. Good luck
@ryannolin9692 3 жыл бұрын
12/5/20 who hasn't liked and subscribed, if you like the video...then like the video
@1AAuto 3 жыл бұрын
+Ryan Nolin Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@dylanblack854 4 жыл бұрын
Great video but I hope you're replacing that pinion seal in your diff next ;)
@1AAuto 4 жыл бұрын
+Dylan Black Thanks for watching. We'll keep this repair in mind!
@MarcusWoods 3 жыл бұрын
@@1AAuto what did they see that showed a replacement was necessary?
@irdiver3 Жыл бұрын
should you lube adjuster??
@dmagil01us Жыл бұрын
In what world does a 20 year old drum brake pop right off? This video would be useful if you went over ways to get a stuck drum off.
@schonau1969 2 жыл бұрын
Why are we not putting brake lubricant on the six contact points of the break shoe?
@MrsBuddevil 9 ай бұрын
Can you drive without the "spreader plate" aka parking brake strut
@577buttfan 2 жыл бұрын
I always spray them down with LA Awesome and rinse before doing the job you will stay alot cleaner. This is a pain in the ass job for sure.
@ZuffaLtdDanaWhite 2 жыл бұрын
Why
@Alphawolf2325 5 жыл бұрын
Can I get a link to this brake kit for my 98 ranger 2WD? All I'm seeing on the website are kits for 4x4 rangers
@1AAuto 5 жыл бұрын
+SamYouPlays Thanks for watching! It looks like we have kits for the front of your vehicle, but not the rear. We may have the individual parts available, just not in a kit. You can take a look around our website to see if we have the individual items you need. 1AAuto.com
@FordRangerClassics 3 жыл бұрын
I have an 03 edge thats 2wd but sits on 4x4 so it makes life so much easier lol
@Tylerw_12 8 ай бұрын
I thought about doing this myself but after see all the things falling off and pulling apart of the springs and stuff there’s nooo way those things will be put back together right😳😂
@TroKush215 25 күн бұрын
Anyone in the Chicago area would like to take on this job?? Obviously will pay
@kowhort 5 жыл бұрын
Good video but you didn't replace the wheel cylinder. Would have liked to have seen that.
@1AAuto 3 жыл бұрын
+Mentally Deranged 916 Thanks for the tip!
@rhymeswithteeth Жыл бұрын
You neglected to add some anti-seize, or high temp brake grease, to the grease pads on the backing plate.
@scottandjodiferris4210 3 жыл бұрын
I'm doing an 02 sport trac and had a piece fall off and didn't see where it fell from. I don't see it in the video anywhere. I wish I could post a picture of it...
@FordRangerClassics 3 жыл бұрын
Post a video lol
@chancebower2958 6 жыл бұрын
Why can’t a find a E brake actuator for my 04 I need one and it seems impossible to find or are they universal as long as there for the drum you have?
@1AAuto 6 жыл бұрын
+Chance Bower They should be specific to the vehicle. We currently do not carry the replacement for your vehicle. You may want to ask the dealer to see if they can get a new one for you. 1aauto.com
@chancebower2958 6 жыл бұрын
That I you I didn’t buy the vehicle off of a dealer but would I be able to still get the piece from the ford company
@savoryhd 3 жыл бұрын
Any tips? i have the same problem
@phildeveney1247 5 жыл бұрын
I have a 2011 rwd. Is it the same assembly?
@1AAuto 5 жыл бұрын
+Phil Deveney It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model. Thank you for asking. 1aauto.com
@rem45acp 5 жыл бұрын
Why do you want to adjust the shoes to lightly drag on the drum? Won't that make the brakes always lightly apply pressure even when not braking?
@mathewm7136 5 жыл бұрын
That way, the drum will apply braking pressure at the same time the fronts do.
@phim4674 4 жыл бұрын
Good video, very informative, but flat blade screwdrivers are not pry bars
@stevethedonful 4 жыл бұрын
A tool can be called whatever you want.. the point is using what is available in different applications.. pry tool, screwdriver, lever, chisel..
@markh385 5 жыл бұрын
I’m doing a transmission service on 06 ranger I’ve heard mixed information on the transmission fluid I should use so has me wondering so what transmission fluid should I put in my truck
4 жыл бұрын
Duhh Maybe go to a transmission video
@lesismore286 3 жыл бұрын
You really should make sure you emphasize the adjustment cable clip is seated in the shoe!
@LetricShave 5 жыл бұрын
I think you got the sequence wrong on the top springs. The green spring should sit behind the yellow spring. Also, a mini pry bar with an angled tip and some tape wrapped around the tip would prevent the wheel from getting gouged up from a screwdriver blade twisting and prying against it.
@johnhenryholiday4964 5 жыл бұрын
Mine came from the factory with the yellow spring behind the green.... but... I dont think it much matters actually.... Im on my second rebuild have roughly 200,000.0 miles on the old rig.
@kristendithomas3522 7 жыл бұрын
what size brake shoes does a 95 2wd ranger have? I seen there are two choices 9 and 10 inch.
@1AAuto 7 жыл бұрын
+Kristen DiThomas You may have to have the dealer run the VIN number for you, or you could measure the drum with a tape measure (take the wheel off first) We carry the 10" drum brake shoes. Here is a link to them www.1aauto.com/brake-shoes/i/1abps00882?f=987236&y=1995&KZfaq&CTA%20Comment&
@thisismyjunkmailboxforyour9172 6 жыл бұрын
9" for standard cab, 10" for extended cab
@charlespacejr3213 5 жыл бұрын
@@thisismyjunkmailboxforyour9172 I have a standard cab and 10 inch drums. It all depends on the exact model and vin.
@jackmehoff9047 4 жыл бұрын
I have a 96 Ford Ranger Ext Cab 2WD and just recently my right rear wheel cylinder is leaking pretty bad causing a very soft pedal. My Master cylinder is brand new. I've been having to use the E- Brake to stop,yes I know that's dangerous, but here's the kicker. The other night on the freeway I heard a loud banging noise coming from the rear. I pull over and that same tire with the bad cylinder is being held on by one lug nut the rest had sheered off. How in the hell could this happen with a bad wheel cylinder?
@slowride55 4 жыл бұрын
Jack MeHoff completly unrelated
@Striker50_ 10 ай бұрын
0:58 How to remove hubcap
@colli_wolly 4 жыл бұрын
11:10 I’ve place a new pivot piece on there, but it keeps falling off. Is it supposed to snap into the hole?
@matthewjustice3383 2 жыл бұрын
03 ranger please
@mikej.2803 4 жыл бұрын
And what's the process when the drum does not slide easily off the axle? And your brake tool will not turn the adjustment spacer because it is rusted to all hell? Have beaten and pried the drum to get it past the brake pads but no luck. Is there another Choice besides getting my angle grinder out and cutting the drum in half? There's got to be a special trick out there somewhere, help! :/
@richardjacques1731 Жыл бұрын
You can pull the retaining pins from the back and cut them off with wire clippers. This will allow the shoes to collapse inside the drums.
@poochsworld 3 жыл бұрын
This will work for a 98 Mazda b2500, yeah?
@1AAuto 3 жыл бұрын
+pooch's weird world The part in this video fits your application, and the install should be the same or similar. Buy this part on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
@rupton1001 6 ай бұрын
Removing the e brake bracket was the worse choice I ever made…. Could Of said it was a pain to get back on
@drifting1O1 7 жыл бұрын
any info on the TSB? my o4 Ranger is affected and I keep getting water and dirt in the rear drums. casing saver brake grab and lock up in the rain. apparently, the dealer fixes the problem by applying silicon to the backing plate? but they won't tell me where I need to apply it. Thay would rather I kill myself then not make any money off me.
@1AAuto 7 жыл бұрын
You're local dealer should have any updated TSB info on the vehicle. Hope this helps out 1aauto.com
@nickfeness 3 жыл бұрын
i dont like using a screw driver to remove the hub tbh. It does cause damage when you could just wrape it in a microfiber. i use a crowbar with a microfiber on the corner of the pry tool. super easy and no damage.
@1AAuto 3 жыл бұрын
+Nick Feness Thanks for checking us out! 1AAuto.com
@nickfeness 3 жыл бұрын
@@1AAuto for sure! You guys are saving me mega bucks on my new truck :D
@MarcusWoods 3 жыл бұрын
@around 7 minutes 30 segonds it talks about putting a spring washer and then the horseshoe clip is seated. I don't have the spring washer and my e brake part doesn't look 100% the same. Is it possible I don't need that?
@tadair705 3 жыл бұрын
Some don't have the spring washer and horseshoe clip. My 1996 2WD doesn't. It has what looks like a tab that fits into a slot on the backside of the shoe.
@gunfisher4661 Жыл бұрын
You have to use the spring washer from the old set as the the parts kits don`t include that part it helps the e-brake move smoother. Mines an 02 that i`m doing right now and I had to replace every thing adjuster and all ,also the parts kit don`t include the brass anti friction washer on the star adjuster either you have to reuse off the old one. just a way of chincing for a buck I guess.
@mlmebrock0213 4 жыл бұрын
Gentlemen, please, add to your list of tools. While it is not *NEEDED*, a furniture clamp (www.harborfreight.com/6-in-ratcheting-bar-clampspreader-64154.html ) will make remounting the shoes so much easier. I have a weak right hand, due to a childhood accident. So, inspiration hit me and I used one to hold the backing plate and shoe together. It made the three pieces (pin, spring, and slotted clip) a breeze to assemble, alone. Turn someone's "disability" into an *OTHERWISE ABLE*, thank you.
@1AAuto 4 жыл бұрын
+Edgar M. Mosier Thanks for the feedback!
@jimirox1928 5 күн бұрын
Ya Know, Guys/Girls. USA made cars have had had pretty much the same drum brakes since the mid 1950's. It seems to me that the rear drum brakes use far more parts than the front disc brake hardware uses. Disc brakes work so much better than drum brakes and so are much easier to to change out. Sorry.... I just don't get it.
@aparedes22 2 жыл бұрын
That last spring…..yeah, it shouldn’t be last!!!!
@gunfisher4661 Жыл бұрын
Green one was last on mine and it had never been touched before.
@davidkelly7485 2 жыл бұрын
You needed to make it clearer which side you were currently working on-left or right. Difficult to tell from video.
@bopahay 3 жыл бұрын
You left all the rust on a lot of those parts and didn't lube the backplate.........no wire wheel in your shop??? Check out South Main Auto Repair, Eric does it the right way.
@rexdrax4649 Жыл бұрын
Have you ever done a brake job
@rexdrax4649 Жыл бұрын
You don't need to look at the other side
@EnviroSteward 3 жыл бұрын
Remember this is the PASSENGER side. I lost a few minutes in disorientation
@rexdrax4649 Жыл бұрын
No ranger has a wheel lock key
@Graff-zr3tn 2 жыл бұрын
Doing rear shoes on fords can be difficult task. I prefer to avoid Ford's altogether. Still a good video!
@LuisRivera-bt4ti 3 жыл бұрын
Forget the grease
@McL0vin2131 5 жыл бұрын
My adjuster doesn't touch the metal clip thing on the bottom. It's supposed to touch so it stops the adjuster from moving. I've done everything right, it just doesn't touch...
@jasonpoirier5336 11 ай бұрын
Did you find solution? I have same peobleme
@juanvelazquez5636 2 жыл бұрын
✨️✨️✨️✨️✨️
Dharni
Рет қаралды 151 МЛН
Gufee.medalin
Рет қаралды 5 МЛН
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 4,3 МЛН
EVERY DAY I RACE
Рет қаралды 238 М.
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 166 М.
Будни дальнобойщицы Merdgio Life
Рет қаралды 470 М.