No need to request for like.......It's perfectly good video..... thankyou

You can't go wrong with this thorough instruction...Thank You!

I LOVE YOU SOOOOOOOOOOOOO MUCH, thank you sooo much!!!!!! I was trying to control stepper motor using L298n with nodumcu, my input was more than 12v and I forgot to remove the jumper your one tip made my day thank you soo, by the way your explanation was perfectly good you walk through every simple steps and I appreciate that. Thanks once again!

Was struggling to do a project with motor drivers! and BOOM .... Now iam able to complete my project as if it was a magic😉 Thank You soo much for ur fantastic video.... Really grateful to have ur video

"Ground Should Be Common For 2 Power Supplies" this solved my biggest problem!!! ThankYou So Much 🎀

I saw many videos but I did not understand a thing, but when I saw your video everything was clear. Thank you so much!!!!!!!!!!!!!!!!!!!!!.

Thank you very much! I got all the information I was searching for quick and simple. Amazing video!

Was very easy to follow.good instructions Can you also do a tutorial on how to replicate a garage door operation with a single push button,that is forward,stop reverse?

honestly a great video i missed to connect arduinos GND to modules GND cause u i corrected my mistake now its working fine thank you mam for great video...

Great, simple, easy to get and short..great work.

Thank you so much, i'm a total newbie to electronics, never heard of this bords before.

OMG you make this so easy to understand. Thanks!!!

What an awesome video.... Thanks a lot . you made my day. I was working on till 6 hours and i was just skipping but when i see your tutorial i got the thing❤️❤️❤️.... Thank you

I LOVE YOU SO MUCH PLEASE UPLOAD MORE!!!! This Video was such a brilliant and perfect explanation without any fancy words and simple to follow instructions! Once again thank you so much :D

best dc motor controller tutotial video so far

Very nice video! In your video you used lower voltage to drive the motors. In my case, I want to use arduino+ L298N to control a 24V motor (full speed). How can I set up the connection to power the motor (preferably not using a breadboard)? Thanks!

Thanks mam you helped us to find the problem for controlling the speed of motors.

Girl! This was so clear. Thank you so much.

hia...if I were connecting 2 X 12V @ 0.1A brushless DC (PC) fans to this board, to power the fans and account for the 1.4V loss of power to the L298N transistors, would I be right in thinking I need to use a 13.4V (let's say) @ 2A power supply? If I'm correct, will I then also have to remove the 5V output jumper as it's > 12V? Never knew that was a stipulation regards the usage of the 5V output...is it documented anywhere? Thanks for your vid and any feedback you may have 👍

Just found this video, its super helpful!

thank you so much...you can't imagin how much i needed it

When should I ground both GNDs of Driver and arduino? before or after burning code?

very nice explanation ,easy to understand for a newcomer.

Wow!! Very clear. Thanks and one more thing I have a doubt with power supply. May I use single source of power supply through arduino Vin pin.

It is a great video with clear explaination and background music as well. Thanks.

thanks for sharing the video, if i want to run 10 motors 12v then how does it work, please tell me.

thank you very much for indairectly help in my collage project through your vedio we make the project

" Whenever you use two power supply you have to make sure ground should be common for both " I wanna marry you for this line. Thanks a lot specially for this. (I had a problem like touching the heat sink (that black metal) increases the power of motor)

this video is helpful. it helped my to solve my issue with motor driver

THANKS A LOT, I HAD NO IDEA OF HOW TO REMOVE THE JUMPERS

Can I use 3S (2200mah) lithium Ion battery pack as my input to the motor driver..?

Extremely amazing video. Keep it up!!

I love this channel. Recommended. 10/10. Outstanding.

Maam please tell are u using an transmitter or remote how are u controlling it

Your explanation is very high class

Hi ma’am, I have a doubt . I have a pump of 3.7v,0.1 A and can I connect that to this L298N .If so what are the changes or additional components required Pump is - kamoer 3.7v 0.1A

Well Explained, nice video, I m using a 5v power bank as power supply, can I use it to power the motors, if yes where should I connect the +5v, the 7-35v pin or the 5v output pin

Umm we have to connect the enabling wire with pwm? Or the input wires?

What about the 5v on the l298 where is it connected to on the arduino

thank you for speaking english well understand always watching

Hie mam it was wonderful tutorial I am using 2 batteries 9 volts but it is not following the programm it doesn't run anti clockwise

are BO geared motors necessary ? or we can connect toy car DC motors directly ?

Mam can I use this driver with 5v DC motors are they compatible with it please reply fast I need to do that for my project

Nice explanation best of luck for next video

Hi, tnx for your awesome vid, I got a question, what is the minimum current required? I'm using two 9v batteries that are paralleled and yet it doesn't work (hardly moves)

Thanks for the clear explanation.

lady is so sweet her voice is like melody and you understand everything

What if we used a motor driver shield. Do we still have to power the Arduino separately?

how to control dc motor speed via bluetooth range? meaning if distance is beyond the certain distance motor speed will speed up? it is possible?

I have 3 TB6612FNG motor driver. I am trying to connect 3 motor drivers to arduino. Which arduino should i use?

awesome and precise!!! thanks, ma'am

can we activate the motors alternatively by using this circuit but different code?

Thanks a lot. Very easy demonstration

Mam, what is the maximum input current that could be given to L298n

thank you for this video but If i want to run 4 wheel with L298N motor driver and arduino mega 2560 then how will i do connections

How many voltage are u using? I tried mine but speed of the wheel is pretty slow and somehow only one wheel is working. Btw im using 6V connect both Arduino and driver

With the same motor driver i can only operate one motor...whenever i connect both motors it stops working....is it because i am using a 9 volt battery with the driver?cause individually they work with full power...what should i do?

Hey ma'am . Can we control two l298n drive using node mcu board ? Please help

Perfect, thank you

We can use for 24v dc motor 250w

Mam, can u please provide the code for the project.The link given is not working

Thank you sooo much, it helped me a lot

Really helpful - thank you!

I am using 9V battery to test the module the motors are running fine without the module but as soon as I give the Input pins (1,2,3,4) high then nothing happens so Is my L298 defective. Please help me out!!!!

Does the testing method only work if the jumpers are there?

Motor rotates with power of battery connected to driver or usb cable?

thank you, very clear and helpful شكرا حزيلا

Very good video ... But 1 question ..... I have L293D Motor driver ic instead of module.... And I don't know how to use it in the same way... Can you please suggest me.?

Can I use 10A current with l298n?

Can i ask, can i use powerbank thank power supply? Please reply

Thank you ma'am it's very useful

Thanks for this video I am stuck with self balancing robot motors not working kindly help.

Interesting video. However, I noticed one motor was rotating from the code in the link, how can this be fixed so that both motors can rotate simultaneously ? Thank you!

You didnt show bidirectional mevement. Is it possible to run motors in opposit directions?

Vo bhi diffrent speed par or anlog input se 4motor ki speed up kar sakte he

can i use this module with a pwm ouput for positional accuracy? basically, can i turn my gearbox DC motor into a servo?

Does the 12 volt input on the driver need to have 12 volts for the motors to work? If I have less than 12 volts will the motors run slower or will the arduino not receive 5 volts?

Should I still use a common ground if my motor voltage is different than my 5v logic circuit?

I am using 3*18650(12.6) volt Do I have to open the jumper wire?

Great teaching ,thanks alot

Whats the average voltage drop in this driver?

hi does anyone have idea what motor and tyer is she using

Thanks for your Tot, It was very good.

Dear respected brother, I am beginniner to use Arduino, sir i upload built-in led blink example sketch to Arduino uno and pro mini, both are blinking well, then I upload empty sketch to clear example code, system shows message that sketch upload done 100 %, but both boards runs previously blink example code. I tried to different systems (PC, Laptop,mobile) to clean an upload new sketch, but results are same, where I mistaken i don't understand. Pls help me to solve if you interested.

If my motor is working on 12 v then 5v is necessary or not?

How can I use same time 50motor in using one sirkit

Thanks its best totorial for testing l298n and arduino..

can i use standard 9v battery reply fast pls......

Which code u applied

Can we use 4 motor on it for motor car

Can I use 2200mAh, 11.1v, 3c lipo battery

Can we use dc motor instead of a gear motor

Can you show how to make obstacle avoiding car with two IR module sensor

its amazing explanation thanku

What DC motors did u use

thanks! very nice tutorial

Please show us how r u sending signal to the motor, I mean it's through some mobile application or from Laptop . Please clear my dought

please make one video on bldc motor control

I desperately need help, both motors are connected to PWM pins but one motor spins faster than the other. I've tried many things and nothing works. Please help

from where we buy cheapest ardiuno