seems like all the experts like to watch video tips on doing what they know best!

Thanks for the tutorial. Gave me the confidence to tackle a job with a lot of cutting in an edge about 200 linear feet, and by the end I was feeling a little confident. It was outside under the ever of a two story house so didn't need to be too perfect, but my confidence has grown where I'm going to tackle my garage door next. I'm a clutz, but your technique helped out a lot, no more taping for me.

Brush marks when cutting in are the bane of a quality paint job. You need a paint brush in one hand and a mini-roller in the other to roll out as close as possible to the trim to get rid of that obvious reservoir of brushed paint. When it dries the cut-in portion is obvious and and ugly with brush marks. Painting the trim first is fine if you're doing a tract house or a rental. The downside is splatter from the roller on your freshly painted white trim. Production painters who wish to get the check cashed asap will do that and make you believe you only need one coat of paint, but a painting craftsman knows a fine paint job takes time and patience. Also, you're using semi gloss on the trim and flat on the walls so if you overlap semi on the walls too much you still have to cover it with flat. Covering flat on trim is less noticeable than the reverse. Trim painting is the crowning achievement of the paint job: Finis coronat opus (the end crowns the work) Two coats of semi-gloss trim paint are required so just take your time. No matter what anyone says you need to do two coats of wall /ceiling paint and two coats of trim to make the job rich and vibrant and make the paint job really stand out. If you do just one coat of each then you will see holidays on the wall or non-uniformity, and the trim will not stand out in contrast as much if you skimp and do a one-coater. Also, trim paint takes longer to dry to a solid state, but wall paint dries fast and ready for re-coat in a few hours. Two coats on walls/trim and the homeowner is going to say WOW! just before they write the check. A one-coater job and they probably won't say anything more than thanks, and they won't refer you to a friend or family.

I like the technique. Thank you. I’ve seen plenty of self-proclaimed professionals do really lousy work. Most likely those making negative comments. That’s why I do all my own work.

That’s why I love this show you always learn something

I've tried taping off doors/baseboards/ceilings/etc., I've tried using special tools for perfect edges, and I still made a mess of it. When I just fanned out the brush and painted up to the edge myself (like in this video) it came out SO much nicer. It seems the harder I tried to have perfect edges, the worse it came out.

This is a very informative video. So that’s the best way to do edges. Thanks a lot!

This is a good basic tutorial for the home owner...helps with setting the brush technique and spreading out the paint before bringing it in close to the casing...ofcourse for residential/commercial painters that are painting 20-30 Doors a day it would be to either brush/spray the door casings first because of time factor and experience. Nonetheless, everyone has to learn the basics first before we can move on. Thanks for the video on the techniques...great homeowners paint tips.

You have to paint a minimum of a gallon by brush to get the hang of this. There's no avoiding that, once you do painting isn't such a drag, and you can also save some money by not needing blue tape for all the trim in your house.

I always paint trim first.... it much easier to cut in up to trim than to try and cut the 3/4" or less edge of trim.

I have never seen a weirder work flow! This reminds me of a framer trying to paint!

Nice demonstration, I like to paint the trim first as the wall seems easier to cut in.

I'm a professional painter of over 36 years and I have never seen these contraptions work correctly. Man you must understand to do you are saying requires perfect drywall seams. In my world, there are no such things! I have painted in houses valued at over $300,000 and even in those, you will see drywall flaws. You paint ceilings first after you insure your edges are straight. You caulk and fill in nail holes in your trim. Then you paint the trim next and it's ok to go a little bit on the wall because you insure that perfect seal between trim and walls. Then you carefully cut in your walls and stay off your trim with a nice straight line. This process saves me 30% time in labor making my work much more profitable.

So far in the 21st Century, the internet has provided a channel for snarky, angry people to vent in ways you hope they wouldn't in society - but life imitates art (in this case KZfaq in place of art) and now you run into more and more folks that speak to each other the way they do in the comments to a video, i.e. ruder than hell. I'm too old to figure it out. Life is such a neat experience, with love, and children, and their children... with music, and natural beauty, and even with growing old with someone you love. Why spend all this energy telling someone their work is crap? It's not enough to simply say, "I do it this [different] way and get this [different] result. If the comment makes sense, readers can learn - in some cases I've seen the original poster come back and explain his/her point of view. There can be communication and learning, without snark, without profanity. I guess that wouldn't fulfill somebody's inner need to strike out at someone that approaches things differently from the way they approach it. Makes me sad - it's not that the 20th Century was so pristine, manners wise - it's just that prior to the internet, we didn't get everyone's every single thought, angst, anger, and God only knows what else shoved in our faces. It's why I stopped reading Twitter. I learned some things, but mainly I learned that a whole lot of people are angry, and very likely lonely. Sad. Peace...

This is very helpful for me, thanks

Best video on painting I've seen

Very good video! Thanks!

I've probably been painting before most of you were born I'd say the guy looked pretty clean and reasonably professional. I would cut in much faster with a 4 inch brush but he wasn't that bad. The spinner is used by many high quality painting companies, I used to use the spinner myself but it's too slow because you gotta clamp the brush on and off. When you paint for a living you need to get the job done with good quality and get the hell out of there but it's good to have a system

Its easier to cut in the sides of the trim first with the trim paint, go onto the wall 1/8 of an inch or so, then cut in a nice line along the trim with a couple of coats with wall paint

There are some great tips in this video that I will try. How would you go about cutting in say a wall next to a door frame if the wall and door frame are uneven? Sometimes I have trouble determining where the wall finish's and the door frame begins. Any advice would be appreciated.

can you show how to prepare to paint a weathered board and batten siding

Does wetting your brush before applying paint work to better clean out?? Or does paint water run down the brush handle ???

How about rollers? Should it be wet first and then spun until slightly damp?

This is the first video that I have seen where the guy actually explains what he is doing, rather than just watching him.

Totally agree with this. It’s okay to paint the trim a little bit it looks perfect

That bucket your getting paint out of: where do they sell them at? I have the Wooster bucket but doesn't have the place to put paint brush at.....

Even if the casing is going to be painted later I always start a room by painting the returns first thing and it’s dry by the time I’ve finished the rest of the cutting in it’s a much easier cut to paint the wall after the return has been painted than to paint the return last.

Check out the new Richard gooseneck flexible paint brush extension. Best brush for cutting the straightest lines! And perfect for high to reach places. Bend it any way you want!! Cheers!

I have been a painter for about 20 years and once you learn how to load a brush all this in the video doesn't matter.

Thing i dont like using any kind of paint brush on trim & cutting corners leaves brush strokes 4" roller works well blends in with 9" roller.

Good technique. Never thought of wetting the brush first. Where do I get the thing that spins brush

His 'reservoir', lol.

Paint your trim first and then cut in and then do the walls

the first thing i do is prep the walls because that's what makes your paint job look good, next i paint all trim first

Never mind the reservoir BS. Load the brush, start at the top corner of the trim and run the brush tip down the edge where the trim meets the wall. Reload, go back and bring the cut out 1.5 inches. 3 minute per doorway

I make a belt with a plastic protein jar. Then I have a dishwashing soap bottle full of paint. I squirt the paint onto a square edger. Then I apply it to the corner. Sometimes I use the side with wheels. Sometimes I use the other side. Then I have a brush that I use to brush the line that it creates. That’s the fastest and easiest way I have learned to do it.

well done

My preference is to cut the architrave around the door first. Reason being it's easier to cut the trim into the wall, than to cut the wall into the trim. Some people prefer to do it that way, others don't. I think it's all about preference.

A lot of "expert painters" in the comments

It worked! Even in these god-forsaken textured walls and ceiling. 👌👌👌

There is an Aussie guy on YT that says do walls first then trim cos when doing walls last you can get spatter back on the trim.

Could you create a video of cutting in next to white next to woodwork?

Why don't you use masking tape around the edges? Me normally using the tape around where the unwanted paint area. like this kind of trims. Anyway thank you

I always paint my wall first then install trim after it’s painted. Then if I need touching up it’s tiny.

The brush he is using is an angle sash.looks like a 2.5 inch or 62mm brush if anyone needs to know which one to use.

Thank you for this video. I did a great job and no mess. I did have to watch it 3 times.

what is that tool call which spins the paint brush. pretty cool gadget

Thank you so… much

or you can use thin piece of plastic sheet and use that to block other side from paint and get a straight line

Will wet my brush noe I was getting Dryed up paint balls on wall. I was planning to clean brush😊

Can you make a video showing us how to recharge our air conditioner units in our homes? Mine is a combo 5 ton. Thank you.

I paint ceilings first then I cut down the edge of all the casings, cut in the walls then after rolling the walls you paint the face of the casings. I don't wet the brush because the water will pull the paint up the bristles to the metal part and your brush will get really messy fast. And I don't spin the brush out because that ruins the brush faster by separating the bristles which ruins the brushs pointed end. I snap the brush down flinging the water off a few times which keeps the brush from flaring out ruining it.

This is absolutely sterling content. A related book I read served as a pivotal catalyst in my life. "The Art of Meaningful Relationships in the 21st Century" by Leo Flint

Do you see this guy's hair he's an expert with all brushes

Here's what I've learned after cutting in and painting numerous walls and ceilings. Go to Hobby Lobby and buy a package of artist brushes; I think they were around $9.00. There's an assortment of brushes big to small; 4" - 1". The bristles are very fine and they will lay down a beautiful straight line. Never had much luck with using brushes like the guy in the vid.

I love to see him on price work 🤣🤣🤣🤣

He just added 15 minutes to every casein. I ALWAYS HIT THE CASINGS FIRST!

Wetting the paint brush before using it is a mistake imo. Wetting it while painting is even worse. A wet brush allows the paint to wick up towards the ferrule quicker. A wet or freshly washed paintbrush doesn't apply paint as well as a dry one. It's easier to cut-in a wall next to painted trim than to cut-in trim next to a painted wall.

i just use a straight edge and slide it down with the brush next to it

doesn't the water dilute the color to a lighter color?

Even with a lot of practice, I still suck at it

paint the trim first. nice hair and uniform though

At list you have tried.

Only if you don't mind seeing brush strokes. Really, it's not like you have to do this every day, every week, or every month. The paint is going to last for years for most homes. You only do it every few years when need to, so don't be cheap. Just buy some tools for painting edges. They are just from a few dollars to $30ish. And it can help you paint edges much cleaner and more importantly, it saves you much more time than painting so carefully little by little with your shaky hand. By the time you finish painting 1 side of the edge with your hand, i already swipe through all edges.

I would never let this guy paint anything. What a hack..lol

ماشاء الله😇🙏👼

3:13 - 'Skirting' sounds better than 'Baseboard'.

hahah nice thumbnail

This guys hair is classic.

paint the trim first .... then cut the wall into the trim using a little more pressure on the brush to spread the bristles out you'll get a cleaner line

"Kevin,kevin..................................Kevin..............KEVINNNNNNNNNNNN!"

just buy blue painters tape. 3m has some new edge seal tape. it's expensive but easy

The secret to being professional painter is knowing how to use a flex blade putty knife. I'm I right painters?

Me queda mejor a mi

If wet brissels worked then why damp paint brushes ruined more then 1 paint job.??..

Pay him $4 an hour at that production level

I guess caulking the trim wasn't in the plans....this was terrible

the only valuable thing was the 5 in 1 trick w/ the cloth 🤗🙄☺🙂

That's why your pants have pocket just for it.

Well, my old art teachers would have a fit over smooshing the brush out.

Woodglut comes with very useful plans with all the details you need.

Painted for over 40 years and worked with hundreds of different painters, never have I seen any of them wet there brush first! And his 'reservoir' just a tap or two does the job. Nice brush tho. A lot of mis information here. Not sure if this guy is a professional painter or what.

I saw this guy on Shark Tank, & for that reason... I'm out. What a circus

first thing you should do is finish trim before you finishing walls and cutting and doing baseboard the last,washing brush every 3 min it's not necessarily...

The only thing this "expert" painter is thinking about is when he can have his next sip of Natty Ice. All professional painters are drunks. Witness that first hand.

I always paint doors and windows with the same color of the wall.

Intelligent painters know to use MASKING TAPE whenever possible to produce clean lines and they WEAR disposable GLOVES to keep their hands clean! If masking tape won't work (such as on a "popcorn" ceiling), a good paint shield will work fine, if you clean it every so often, while painting. I cover the edge of the shield with Scotch "blue" tape and don't have to worry about cleaning it so much after use. You need only wet the TIP of the brush (maybe a quarter-inch up) by running through a little clean water before first dipping it in the paint. Dipping a totally dry brush into latex paint is a mistake.

I've never seen a painter use a spinner lol, use your hands dude, oh and by the way i don't wash my brush half way down a wall, i cut the the whole house and works perfectly,ive never had a problem.

Be I don't care who you are, you can't freehand and be perfect.

Everybody knows a sash brush is used on sashes window sashes or maybe picture frames but really trimming? Block brush only that way your lines don't look like your a drunk

The first line way to much paint and when he backbrushed he didn't backbrush close enough to the wall so ur gonna get a cake on look which is horrible so when you roll it out and it dries ur gonna see a different texture all around ur cut in lines the. Ur roll texture....CBM painting

Don't press too much the brush.

There is nothing I hate more in this life than painting.

Dude has hair like former Illinois governor rod blagoiaveich

if your in the trade you would not use that stupid spinner lol. nice brush but stupid wet the brush routine

Always paint the trim first dufus To many things wrong with these techniques to elaborate. Yes I'm not only a pro I'm The best

Proof that even "This Old House" haven't a clue about painting. Norm, the carpenter and the plumber are always great but this guy? Gimme a break

Maybe for a DIY that might work. But you dont put water on your brush in the middle of the wall or push as hard as he is (all you will do is take paint off). I as a professional of 15 years in this field would say this is NOT how you cut in.

Dat buckaroo aint no painter 😂😂😂🤣🤣

داداش اشتباه میزنی