How to do Horizontal Stamped & Carved Concrete Overlay Step 3 of 4

Рет қаралды 80,366

7 жыл бұрын

Stone Edge Surfaces Horizontal Training Video series.
From mixing the mix to primer to application, stamping carving and coloring. This series is a How To guide on doing basic horizontal stamped overlay. This is video 3 of 4 in the set.

Пікірлер: 31

7 жыл бұрын

good video

@lucideyemedia 3 жыл бұрын

My boss always had me stamp to the very edges. No giving up, smaller stamps put texture all the way into the edges. Good vid though! I learned about the shoes! Had no idea

@BL-su5wt 2 жыл бұрын

Great video! Thank you for the clear explanations. I was wondering how you would do the verticals on steps. Would you just recommend smaller texture mats? Also, how about the logistics of steps and the flats. Would you do the verticals first, or just continue all of it from bottom up or top down. Sorry if my questions sound ignorant

@almirsouzamf 4 жыл бұрын

Muito bom! Como faço para adquirir estas estampas? Aqui no meu país não tem pra comprar

@amisela7261 3 жыл бұрын

Hi I’m a general contractor from Los Angeles , I love your creativity . We are getting ready to buy some product from you. I would like to know what concrete overlay product did you use in this video.

@questconcrete 5 жыл бұрын

Stamp your stone and then you’re plank if you want to get right to the edge. I roll my seamless stamps down and roll them back too lift. I never pick it up straight up and down. Suction can often make a mess. In fact most seamless stamps are too large to pick up like you say. After trimming your edge go over that edge with a small paint roller to round it over a bit. Just some of the ways I do things. Hopefully just some helpful pointers.

@baconneggs2406 5 жыл бұрын

Same...the wood stamp will stamp right over most other stamps

@almadellamangus2778 Жыл бұрын

What is the mix of your concrete? The ratio of fine sand and cement?

@MrPorter97 5 жыл бұрын

Is this product suitable for outdoor use where it is 100 + degrees in the summer and -15 in the winter? Can it be used for vertical surfaces like steps?

@stoneedgesurfaces3959 5 жыл бұрын

Yes to all your questions. We have distributors in Buffalo NY where it gets as cold as 60 below zero...and we have a factory and a distributor in Mesa Arizona where today...it's 115 degrees! And...we have different mixes...some are better than others when it comes to steps, driveways, walkways walls and patios. go to www.stoneedgesurfaces.com and look at our gallery.

@Noorstud 6 жыл бұрын

Nice job. Where to order the wood Plank Stamp and the Coarse Floor Texture Stamp ? Thanks

@stoneedgesurfaces3959 6 жыл бұрын

If in the US call the Stone Edge Surfaces office at 844-786-6333 and Suzanne or one of the staff can help you. If International...send an email request to info@stoneedgesurfaces.com.

@mikelarry9888 5 жыл бұрын

Nice

@stoneedgesurfaces3959 5 жыл бұрын

Sorry for the later reply! You can order them from Stone Edge Surfaces. email me at info@stoneedgesurfaces.com and I will get you the information.

@akungwelly 5 жыл бұрын

Answer please did you mix sand with the concrete mixer cement ?

@stoneedgesurfaces3959 5 жыл бұрын

No...Stone Edge Surfaces products have all ingredients included in the bag...you just add water.

@dssequoia 5 жыл бұрын

How long do you let the concrete cure before you texture or stamp?

@stoneedgesurfaces3959 5 жыл бұрын

With Stone Edge Surfaces Stamp mix you can start stamping within an hour and carving within a few hours...depending on other factors such as temperature, etc. that may make the concrete cure a little faster of slower.

3 жыл бұрын

First time I've seen him on his knees.

@akungwelly 5 жыл бұрын

Did you mix sands with the concrete mixer ?

@stoneedgesurfaces3959 4 жыл бұрын

No...these are all pre-sanded mix

@Iliketoweldandbraze 5 жыл бұрын

Boy I wish KZfaq was around when I starting a business when I have started nobody wanted to share what they knew or you didn't know the products are out there or maybe they weren't there I don't know

@stoneedgesurfaces3959 5 жыл бұрын

Glad you found us!

@uwethomae4127 6 жыл бұрын

Have you a dealer in Germany?

@stoneedgesurfaces3959 6 жыл бұрын

I am sorry I do not. You can order factory direct.

@stoneedgesurfaces3959 5 жыл бұрын

I am sorry, but we do not. You can order direct from the factory though.

@danielholm1987 3 жыл бұрын

How thick is this layer?

@stoneedgesurfaces3959 3 жыл бұрын

when doing Horizontal...we have our depth set at 3/8"

@jimargenio6449 5 жыл бұрын

why does Cameraman have spike shoes on,,,,,,

@stoneedgesurfaces3959 5 жыл бұрын

The trainer has spike shoes on so he is only leaving small impressions in the mix and not flattening and smearing the mix and creating low spots. When you have wet fresh mix that you are trying to screed out at 3/8 or 1/2 inch...and it is a large area that you cannot walk around the perimeter and rake and trowel...you use spike shoes so you can walk into the middle of the mix and maintain the same 1/2 to 3/8 inch depth throughout. You just have to smooth out the spike marks, but you don't have to move product around to fill in low spots and footprints that would be left if you walked into the mix and squished the product around your shoes. As far as the cameraman...he did not have spiked shoes on unless he was messing around. ; ) As I was the cameraman...I was probably messing around.

@ismailmdmd3631 4 жыл бұрын

Hi i am from Bangladesh. I like YOU every video, thank fore you,Bat i Ask you can you give me strong calorin name list