How To - Double Flare Brake Line

Рет қаралды 61,783

Fuel Injection Sucks

10 жыл бұрын

How to create a double flare in automotive brake line using a double flaring tool

Пікірлер: 25

@nigelw598 8 ай бұрын

Thanks for the reminder course. It’s been a while. My brakes on the trailer are good as new now after a repair and bleed. Cheers from Australia, 👍👍🍻

@johnbernett8586 3 ай бұрын

Thank you... Excellent

@frank8263 6 жыл бұрын

i just purchased this flaring tool after watching your video i had others that did not flare that good all the time this one works perfectly every time my others did not thank you for your advice money well spent

@davelansfolk7123 6 жыл бұрын

Good job on showing up close every step!.....

@jameswaugh115 Жыл бұрын

I like the way you swiveled that tool around bro😂

@smferreiro2610 7 жыл бұрын

If you take as a rule to tighten first the wing-nut which is closer to the tube you won't need to use the clamp handle. Your hand force will be enough and the tool will last longer. That's the reason why smaller diameters are placed to the center of the tool. Thank you for the video. It has been great to show it to my apprentices.

@drychicken509 Жыл бұрын

what

@lorollinls 10 жыл бұрын

Thanks for showing me how to do this. Been curious about it for a bit but never looked into it yet.

@lordadamfirst 2 жыл бұрын

Cheers, straight to the point!

@elijah2078 Жыл бұрын

Very informative! Thank You!!!

@rx7cl 5 жыл бұрын

nice job.

@gustavomelendez7056 Жыл бұрын

Grasias amigo

@my1after909 5 жыл бұрын

Hi, looks good. I've had a couple rentals, that were crappy. What brand is this? Thx.

@finndog2759 5 жыл бұрын

Thanks

@roberthejl8788 9 ай бұрын

I was practicing using the tool and my line got marks from the clamp bar, is that normal?

@Zeberka767 2 жыл бұрын

If you pause the video at min 1:35, you will notice that the pre-flared brake line that you purchased has two different lengths for the tube nuts. The one that I purchased is the same as well. What's the reason that both tube nuts are not the same length?

@motoprof1441 Жыл бұрын

It looks like the right hand nut does not thread all the way to the end is a metric nut. I may be wrong since it is a bit blurry. The left hand one is threaded all the way to the end and would be a standard nut. It's not uncommon to find standard nut on one end and metric on the other on American cars.

@chiboy002 Жыл бұрын

i know a little late but the longer one is for installing on the back of a knuckle/hub. its just to make the nut longer for easier access, otherwise it is the same nut generally

@officaillilhoover5649 5 жыл бұрын

Good job i watched this video and you explained it very thirdly every other video did not ex0lain it correctly

@pygmywarrior3 11 ай бұрын

thirdly?

@gado6438 Ай бұрын

Tri-pod.

@johng1902 Жыл бұрын

Nice presentation, but poor focus control prevented providing a clear view of what you did. Should redo this vid.

@stripecatflippangitnamecha8721 3 жыл бұрын

Dont buy this Old way flaring tool, its junk and its gonna be 5x worst if you flare under the car. Buy the Titan flaring tool. This old ways only good for single flare, and if you do double flare like brake line under the car you need luck. If you do single flare yes this thing work most of the time but double flare like brake line under the car you gonna need prayer