Three easy ways to dressing a grinding wheel on a bench grinder with DIY Grinding dresser: 00:00 Wheel face out of round 00:13 #1 Diamond Blade 02:23 #2 Spring Lock Washers 03:30 #3 Masonry Drill Bit
Пікірлер: 289
@hvacjay40372 жыл бұрын
Wow. Nice effort in trying to help people out but wow. I definitely wouldn't recommend doing any of these methods. Dressing wheel tool and a solid base is the way to go.
@brucesannino61812 жыл бұрын
Useing the diamond wheel to dress the grinder is a very good idea. I only watched the video, didn't listen to the sound track so you may have mentioned this. I would be very reluctant to dress the sides of the grinder wheel. Grinder wheels are not designed for ANY side loading. To much side loading and the wheel WILL shatter on you and chunks of it will be coming at you at very high speed. After all these years I still stand to one side and reach over to turn grinders on. I wait until it gets to full speed then move in line with the wheel to do my work. Still the diamond wheel is a good idea. I also liked the way you set up to avoid a mess. Well done.
@paulrooster21082 жыл бұрын
👍 Yeppers if possible never stand inline , while true if it grenades it's going everywhere , but standing inline is just bad , like running a tablesaw always stand off to the side of blade . An avoid the cheap grinding wheels also , we had a kid who on his lunch break run up an picked a cheapie one . I really don't know what happened as I wasn't there at that end of The Shop , but man that thang came apart with a Hell'va racket fortunately he didn't suffer any long term injuries , The Shop Foreman really chewed his ass out . I've used the worn carbide cutting tips from the Brake Lath as well , they do a great job on grinder wheels .
@adamechter5536 Жыл бұрын
Thanks man - the split washers worked amazingly well for me! I have a 6" grinder with two stones and both had a big groove worn in the middle of the wheels. I had been looking to buy a tool for this but then I came across your video and decided to give it a go, but with LOW expectations. I mean it's so simple, how could it work better than a purpose built tool?? Well, 20 mins later I had two beautiful, square stones with ZERO cash outlay (had a bolt and washers already). You saved me $40+ and the time to go grab a tool for this. Amazing! And the other plus is that the rig I made with the washers did 2 wheels and look to be able to last for a few more clean ups yet! Some tips if you're going to do this - make sure there's enough clearance on the bolt to allow the washers to spin freely and not too long a bolt to allow you move side to side across the face of the stone (so you wear the washers more evenly). The other tip is this will get Hot, so wear some rigging gloves or similar. 👍
@Toca_waffle8437 ай бұрын
I love the "but with low expectations"
@typoagain12 жыл бұрын
I just use the tool that was designed to do the job. A lot safer. Plus it only costs around $5
@TheMajsh2 жыл бұрын
what tool? can you add a link? Thanks
@dushk02 жыл бұрын
Especially in a rush on a Sunday afternoon...
@gordonsmith96182 жыл бұрын
There's a tool for that , it's called a grinding wheel dresser tool . Works very well for this . Just a FYI 😉
@ryanmcewen4152 жыл бұрын
Yep. Its a must have item
@EvacuatorPro2 жыл бұрын
He called his video " repair without any special tools". FYI
@frogsoda2 жыл бұрын
@@EvacuatorPro a grinding wheel dresser is not a special tool. It's a standard tool if you have a grinder.
@bjondersson Жыл бұрын
@@frogsoda I’ve inherited a grinding wheel, but got no dresser tool. I’m still searching for a shop where I can buy one. So at least for me it’s not a “standard tool”. Until I find one, the tips in this video helps me.
@jbilletz Жыл бұрын
@@bjondersson man everything he showed in this video is extremely dangerous, especially dressing the side of a grinding wheel. You shouldn't even use the side of the wheel much less dress it. Do what you want but these wheels can blow apart and if I'd does you will be sorry. Trust me seen it happen.
@deanhoward41282 жыл бұрын
There is actually a tool made for dressing wheels,it can be bought at most hardware stores & welding supply stores !
@dushk02 жыл бұрын
Costs like a good set of carbide-tipped drills (unless you can get it as a cheap replacement part for grinders ofc but the pro stuff which is readily available over here costs that much) vs 1 old piece. And even if you buy the tool but you don't have the dressing harness for the grinder for any reason, the tricks here are still useful.
@vonpoop11022 жыл бұрын
My wheel dresser (essentially some very hard abrasive on a stick) cost a couple of quid and works fine on small and large bench wheels. Leaves a completely square surface. Must confess I'm puzzled why anyone would need the methods in this video.
@BrassLock2 жыл бұрын
Great methods shown. The list of "chapters" with thumbnails is a great reference feature, much aporeciated.
@user-qt2ck3pw5o2 жыл бұрын
Красавчик!спасибо,вроде бы элементарные веши для технаря,но мне в голову не пришло что можно простым способом балгаркой с алмазным кругом править камень,гениально просто,мои похвалы автору!
@user-hi4sf2uj8w2 жыл бұрын
... только круг не алмазный, а карбид-вольфрамовый, алмазный в10раз дороже стоит и править круг слишком накладно!!!
@user-qt2ck3pw5o2 жыл бұрын
@@user-hi4sf2uj8w в обеходе подавляющая часть знают как алмазный,скажешь такое продавцу,он тебе ответит что не имеет такое,а на лавочке может лежать,так что я давно перестал придираться к словам и терминам,если суть ясна.
@dudemakesstuff2 жыл бұрын
Thanks for the video! I gotta try soon!
@jeffreywolf52352 жыл бұрын
That's a great hack for straightening out your old crooked out of round grinding wheels
@nicolasmiller-vachon40662 жыл бұрын
It can also make the wheel explode. The wheel is not made for sideways pressure
@jeffreywolf52352 жыл бұрын
@@nicolasmiller-vachon4066 that makes sense also if there's a crack in the wheel and you try to push on the side of it I am sure that'll end up pretty badly too
@geoffreybongartz88572 жыл бұрын
Thank you for sharing your video, the video is great and I learned something new today. From Australia.
@henryrossouw9302 жыл бұрын
Great ideas.Thanks for sharing.
@raulimhof2 жыл бұрын
Smart ideas!!! Thank you
@mattman34952 жыл бұрын
Now I have a use for all of my old masonry bits.
@andresjr.garcia94122 жыл бұрын
Very informative video for Diyers like me. Will try this later
@vladimerdarjania71572 жыл бұрын
Good video.
@christiankaiser4442 жыл бұрын
Gute Ideen die einfach nachzumachen sind ich nehme immer ein Segment einer alten Diamantscheibe und schweiße mir einen Griff ran und nutze dies dann zum Abziehen der Schleifscheibe geht auch sehr gut
@petersack50742 жыл бұрын
2:55 right. i used the same idea, lock washers on a large screw driver, works for me. The diamond wheel, on angle grinder, new idea for me. Thankyou, sir.
@michaelwooda94442 жыл бұрын
I use regular flat washers. an old file works also
@leeleebinojer45172 жыл бұрын
Nice shearing 👍
@donlute34442 жыл бұрын
Good to know. I'll use it. I dont quite understand the reason for on/off. Why not just leave it run to the finish?
@marcp11802 жыл бұрын
Weird, I just replaced my old dresser for one of those new fangled diamond coated wheeldressers off of ebay. It cost less than $10.00, is absolutely safe and took about 6 seconds to dress my nappy old grinding wheel. Even if I didn't get the "SPECIAL" tool, I wouldn't use this method shown here, I'd get a new $13.00 stone. Although it worked, I don't like bending the rules that far.
@jbilletz Жыл бұрын
They obviously never seen a wheel blow apart before.
@thomashenderson39012 жыл бұрын
Leave the power on! No need to run down the grinder as it's being dressed.
@joelhart90202 жыл бұрын
It’s Russia, cannot run two tools at the same time
@jarrenbeckman75992 жыл бұрын
@@joelhart9020 how does he have the vacuum on at the same time then?
@thomashenderson39012 жыл бұрын
@@joelhart9020 Ha ha!
@user-pu4mg6bq7r2 жыл бұрын
Wow! Its very useful information!👍
@GOTICDRAW2 жыл бұрын
Excelente vídeo.. Gracias
@inlandspain11442 жыл бұрын
Diamond wheel dresser for me, all day long.
@user-px7zf9tr4y2 жыл бұрын
Спасибо за идею! Лайк однозначно!
@colddun662 жыл бұрын
Рисковый спец. Перо с гроверами засунул между площадкой и камнем, это круто👎😶 так можно пальцев лишиться!!! Да и сбоку камня нельзя точить!👎😶. Опасно это!!! Такие ролики НЕЛЬЗЯ использовать как руководство к действиям!!!
@alexeyzdec23162 жыл бұрын
Не очень понятно зачем делать старт/стоп. Круг отлично обрабатывается и при постоянном вращении.
@parikmag2 жыл бұрын
У него просто мотор тухнет.
@alexeyzdec23162 жыл бұрын
@@parikmag ))) а я не догадался!
@vladimirrudenko42652 жыл бұрын
Да вроде выключает...
@alexeyzdec23162 жыл бұрын
@@vladimirrudenko4265 ну потому и выключает чтобы не облажаться ))
@user-bi8ky1rb9e2 жыл бұрын
Это советские движки, у них сильный тяговый момент. Как бы не должен тухнуть.
@salemaitchalal90212 жыл бұрын
C'est magnifique et merci pour l'idée
@10lenya2 жыл бұрын
With UShM the Best metod. Thank you!!! And good luck :-)
@elektrojen73472 жыл бұрын
En güzel ve yararlı videolardan biri.👍👍👏👏
@margvelion2 жыл бұрын
Когда диск от болгарки дороже точильного...
@feniks76412 жыл бұрын
Не все можно сделать при помощи УШМ
@user-uj8ec7js5b2 жыл бұрын
Я ровняю проще, кусок сломанной рессоры и на включённом моторе потихоньку не спеша слегка касаясь и камень как новый, можно также старым напильником толстым тоже не плохо ровняет
Part of this is scary. One thing for sure, that is a good way to start a fire in a vacuum cleaner. Thanks. Chris
@Ihor_Zhenchuk2 жыл бұрын
Боковую нагрузку к диску УШМ - да он бессмертный!
@serhiiserhio93822 жыл бұрын
Ну он же щиток надел!)))
@richardsweig7622 жыл бұрын
Thank you
@essebaa38122 жыл бұрын
Poco tempo fa aquistai un utensile ravviva mola fatto con rondelle dentate... adesso grazie a te ho scoperto nuovi metodi per ravvivare pietre.
@vladimirka_602 жыл бұрын
Отличная идея, а как алмазный круг себя чувствует?
@Nik999992 жыл бұрын
Подручник для чего дан? Для красоты? Надо деталь хорошо прижимать к подручнику и не давить на камень, не держать деталь на одном месте, плавно водить слева направо, справа на лево, тогда и не будет образовываться эксцентриситет на камне, будет равномерно изнашиваться камень, не следует ломики и топоры на весу затачивать как некоторые рукожопы делают. Расстояние от камня до подручника должно быть минимальное. И тогда не придется ровнять камни.
@user-wm8kd2bc6x2 жыл бұрын
Второй вариант мне подойдёт. Спасибо большое!
@user-ty3oy1wr2o2 жыл бұрын
Блин ну есть ведь спец инструмент для этого чо огород городить и гробить дорогой алмаз по бетону?
@Richar6022 жыл бұрын
Yes you can buy dressing tools ,but what AH would want to when you can do it on the cheap. dressing tools are expensive and only last 5mins So tomorrow morning early you can have a lovely straight wheel .see
@user-hc3ql5wo7f2 жыл бұрын
Спасибо друг
@user-jc9rv8if4y2 жыл бұрын
Спасибо большое
@user-tj9mc3pj6l2 жыл бұрын
Без специальных приспособлений))
@serhiiserhio93822 жыл бұрын
👍😂😂.
@MJ-wh1ny2 жыл бұрын
Grinder from 1986 made in USSR. I have exactly the same. It dance a lot on the table. The body is too thick and therefore the diameter of the stone should be always a bit bigger. I dont use it for last few years.
@frankdodero91572 жыл бұрын
You can grab a rock from the garden and use a steady rest in a pinch also 😗
@user-bh2ot5ks8f2 жыл бұрын
Вроде специальные камни есть для правки и вскрытия дисков
@MazayDIY2 жыл бұрын
Да, есть алмазные карандаши и правИла, а также шарошки, но я решил показать как обойтись без них - для разовой правки самое то, если вам надо выровнять камень раз в несколько лет
@user-mw5qn7tg3t2 жыл бұрын
Благодарю вас
@user-ue1jf3hc2x2 жыл бұрын
А ещё проще ровнять куском от образивного круга который давно валяется где - то среди всякой не нужной мелочи Таким методом я уже польззуюсь больше 20 лет Главное чтобы кусок образива был мелкозернисым и чтоы было соблюдение правил техники безопасности (ЗАЩИТНЫЕ ОЧКИ - ДЛЯ ГЛАЗ И РАСПИРАТОР - ОРГАНЫ ДЫХАНИЯ!!!) ВСЕМ ЖЕЛАЮ УДАЧИ!!!
@user-rw5pv4sw8d2 жыл бұрын
От этого круг засаливается. Ровнять надо алмазным роликом. Или карандашом.
@Davidmest2 жыл бұрын
Я видел на камне сбоку пластины для равновесия. У меня тоже такие.для чего они?не пробовал регулировать их.или лучше не трогать?
@user-kc5jv7mr5x2 жыл бұрын
Для балансировки диска, путем их смещения по отверстиям.
@Davidmest2 жыл бұрын
@@user-kc5jv7mr5x это я знаю.но ничего не получается только хуже.я их снял вообще
@user-ww8xg8fk7t2 жыл бұрын
А алмазным карандашом не проще? И не каких хреновин лепить не надо, болгаркой тоже можно,но это для тех кто не ищет лёгких путей
@Walker77452 жыл бұрын
Наверное проще. Если он есть. У меня например, есть несколько алмазных резцов. Я один заделал в бронзовую трубку и этой штукой выравниваю круг. А болгаркой тоже неплохо. И не обязательно даже алмазным кругом. Обдирочный диск вполне справляется.
@kaban1332 жыл бұрын
С помощью УШМ - зачёт👍 А вот с гроверами - опасно. Так лучше не делать.
@alknis2 жыл бұрын
Согласен. Я даже подумал что с гроверами сразу зажмёт.
@silentcooler41602 жыл бұрын
А почему именно гроверы использовались?
@kaban1332 жыл бұрын
@@silentcooler4160 гроверы имеют закалку, а например шайбы не имеют, поэтому они "мягкие".
@alknis2 жыл бұрын
@@silentcooler4160 хорошая закалённая сталь, не сразу стёсывается
@user-qj2be8do5x2 жыл бұрын
@@silentcooler4160 потому что нашлось под рукой и полезло +- на сверло. А так самая обычная шарошка делается из любых шайб , чтобы свободно шевелились заьсчет этого ВЫКРАШИВАЕТСЯ зерно , из-за удара шайб по кругу , а так еще есть спец Карандаши для правки стоят копейки уж точно дешевле диска на ушм
@serhiiserhio93822 жыл бұрын
Не понятно нафига надо постоянно включать и выключать станок при правке камня?
@dmitrysuvorov71842 жыл бұрын
Я где-то слышал, что можно еще подправить обломком другого круга, часто попадается в хозяйстве. Но успех сильно зависит от материала круга и обломка.
@user-hi4sf2uj8w2 жыл бұрын
...править не получится, а вот почисть- самое то!!!
@user-rw5pv4sw8d2 жыл бұрын
Круг засаливаться будет. Зерно 60 превратится в зерно 100, а то и выше. И точить перестанет как надо. Просто шлифовать будет. Проверено на производстве.
@charlessutton28562 жыл бұрын
But for the people that can't just walk out and buy new tool right away this is a good alternative
@basemmorus9452 жыл бұрын
ممتاز
@XPEHb2 жыл бұрын
Ну уж очень без специальных приспособлений.
@user-dk2eb1hm7m Жыл бұрын
болгаркой с диском - думаю самый приемлемый способ
@TIMUR-ASKET2 жыл бұрын
Вот они и встретились))
@superspecialty51692 жыл бұрын
Ah, yes… the old split lock washer to be used to replace the worn down star rings on a grinding wheel stone dresser. I use the external spiked lock washer, also. I didn’t see you around, 50 years ago?
@user-jy3zf8uw8p2 жыл бұрын
У меня нет заточного станка, зачем я это смотрю, притом до конца.
@user-hd8og2gv8r2 жыл бұрын
Если ты порядочный мужик, то теперь должен купить его:)
@MrFreakwent2 жыл бұрын
The angle grinder diamond disc isn't flat or straight.
@joseandrade50132 жыл бұрын
GOSTEI. IMPORTANTE
@darlioliveira57652 жыл бұрын
Parabéns valeu muito 👏👏👏👏👏👏
@jameschester39862 жыл бұрын
My grandpas sharpened axes and lawnmower blades never seen them ever dress the wheels 😏
@user-fi4pp6ih1h2 жыл бұрын
спасибо за ролик. С уважением к Вам и вашему каналу «Вторая жизнь ПЕТ бутылок».
@danielkonrad14442 жыл бұрын
The real question is, how did it get that wonky in the first place? Especially on the sides.
@HammerOfGrabthar2 жыл бұрын
Brand new wheels come that way. At least the cheap ones do. I bought one from Harbor freight and had to do the same as this guy is doing.
@gman6542 жыл бұрын
When does the "easy" part start?
@ershvv75672 жыл бұрын
Как алмазные диски и болгарки появились в продаже, с тех пор так равняю!!!
@user-sh6nb8ie4f2 жыл бұрын
Второй способ правильный.Алмаз превратит заточкой круг в шлифовальный
@13cheebo2 жыл бұрын
Это почему же? Алмаз чудом изменит зернистость камня???
@user-sh6nb8ie4f2 жыл бұрын
@@13cheebo он срежет зуб зерна и сделает его лизуном
@serhiiserhio93822 жыл бұрын
@@13cheebo А причем тут зернистость? Или не слыхали о черновой шлифовке?
@13cheebo2 жыл бұрын
У таких камней склейка зерен не на высоте. Единственный способ сделать его "лизуном" это поточить на нем албминий или дюраль, забить пространство между зернами укрепив попутно посадку их внешнего слоя. Вот так да. А алмазом не испортишь, следующая обработка черного метала все поставит на свои места.
@Traxman802 жыл бұрын
You made that more expensive and harder than it needed be. For just a few bucks you can get a wheel dressing tool from the hardware store.
@TehButterflyEffect2 жыл бұрын
This is almost a good video. You should never grind on the sides of your grinding wheels! Never! It creates grooves in the wheel and eventually it will thin out too much and come apart.
@1cx2william2 жыл бұрын
I 100% agree. The fact you have to take the guards off should be your first clue you are doing something wrong.
@Robstercraw2 жыл бұрын
There are different wheels. You do grind on the sides. I was a tool grinder for 10 years.
@1cx2william2 жыл бұрын
@@Robstercraw Your right there. But they are designed to be on a side grinder or tool cuter grinder. Which take different wheels then a normal bench or pedal grinder. Normal bench or pedal grinder wheels are not made for side grinding.
@Robstercraw2 жыл бұрын
@@1cx2william wrong. We only used bench grinders. Depending on what you are sharpening you most certainly do dress or shape the side or sides of almost all wheels. Look man, I did this professionally for over 10 years. I know what I am talking about. You don't need to dress the entire side, just the end. If you you are split pointi g a drill bit for example you use the side of the wheel for that. If you are sharpening something that is a v shape you need to dress the wheel accordingly. The face of anything is flat meaning you use the side of the wheel.
@1cx2william2 жыл бұрын
@@Robstercraw one been doing machining for 18 years including sharping my own end mills, gear cutters, and so on. Yes, I have seen people use beach grinders that way and I have seen one explode from it too. The person that had it happen to him had been doing it for over years. Just because you been lucky does mean it the right way.
@serge_msv7772 жыл бұрын
"Хитёр, матёрый..." :))
@sergp.50882 жыл бұрын
Для правки круга есть специальный камень.Называется АЛМАЗОН.Кто не работал на производстве,тот никогда не видел его.У меня до сих пор он есть на даче.
@sergp.50882 жыл бұрын
Хотя и этот метод подходит.
@arrudawagner2 жыл бұрын
Excelentre trabalho.
@user-ti7jx4hv1m2 жыл бұрын
Томского завода точило?
@user-gc7mz7pv7y2 жыл бұрын
Без специальных приспособлений... Болгарка, алмазный диск, пылесос, струбцины - это не специальные приспособления?))
@user-bi8ky1rb9e2 жыл бұрын
Да ладно. А что, нутриометр с набором алмазных брусков чаще встречаются?
@serhiiserhio93822 жыл бұрын
👍😂😂
@user-ll5dh2pf5b2 жыл бұрын
Алмазный карандаш для этого есть
@user-ot1rc9xw4w2 жыл бұрын
А зачем останавливать во время правки?
@balakistaiahm3516 Жыл бұрын
Blade ka name kya hi
@ralph99872 жыл бұрын
Why on and off?
@user-jn5wb6qw4d2 жыл бұрын
Любой негодный алмазный диск отлично правит камни.
@tonyharris73992 жыл бұрын
Use a wheel dreser
@user-gn2hy8sx9y2 жыл бұрын
Спецы пришли к тому что главное хороший круг.потом макс.точная посадка на вал с прокладками и на эпоксидку.потом ровнять.сдвух сторон
@rus-th1kw2 жыл бұрын
Я также болгаркой правлю, но не выключая нождак... Не очень понял для чего вкл/выкл
@petrovich59452 жыл бұрын
На сколько понял, наждак от перегрузки останавливается.
@user-qd4lz3rw6b2 жыл бұрын
@@petrovich5945 такой наждак куй остановишь болгаркой))) имеется такой. В нём дури с запасом, хоть ломы титановые точи.
@user-qd4lz3rw6b2 жыл бұрын
Боится повредить круг болгарки
@petrovich59452 жыл бұрын
@@user-qd4lz3rw6b м.б. м.б.
@user-bi8ky1rb9e2 жыл бұрын
@@petrovich5945 нет, там тяговый момент просто бычий..его не остановишь)). Да ещё и с двойной обмоткой, дополнительно разгонная сделана при утоплении кнопки. Многие не знают..вещь классная, СССР. На оборотах больших может вибрировать и бить сам вал. Поэтому точит на малых, с выключением. Есть модели таких моторов, скажем, не слишком оборотистые, а есть высокооборотистые, на которых есть риск разрыва камня, если тот плохого качества. Вот и не рискует..
@jamesgabioud66542 жыл бұрын
Or I could just but a stone to dress the wheel hell of a lot easier.
@user-fv3sz3uz5w2 жыл бұрын
А может лучше поменять на новий камень.
@tylerdesautels18572 жыл бұрын
There’s a tool for that….. works great
@skor06092 жыл бұрын
А зачем выключаете вращение наждака, когда правите?! Правят на включенном и болгаркой и шарошками))
@MazayDIY2 жыл бұрын
Алексей, выключаю только при правке с помощью УШМ для безопасности
@skor06092 жыл бұрын
@@MazayDIY для безопасности экраны от абразива, очки/маска и тп. А выключением своим вы основной принцип нарушаете - два тела вращения под углом друг к другу исключают ошибки нежесткого контакта.
@user-cr7pt3fg3h2 жыл бұрын
На больших оборотах точно не выровняете, сам мотор трясётся и выберает не там где надо, я прошу друга, чтоб он крутил наждак о другой камень рукой медленно, это я прошёл. Так же на машине неотболонсированое колесо, казалось, что где меньше изношено будет бить об асфальт и уровняется, но не тут то было изнашивается где уже изношено
@user-mg9oe8ti4q2 жыл бұрын
А если через регулятор напряжения?
@user-ii8ch9vb3g2 жыл бұрын
Не ужели так дорого купить правило ?
@rogerpemberton792 жыл бұрын
There are way easier and therefore better ways to dress a grinding wheel that uses the power of the bench grinder not having to turn it on and off. They certainly don't require another electric grinder and still achieve great results. For me this is a great example of over thinking something.
@anglianherbsman99162 жыл бұрын
What happened to that wheel anyway 😮
@vince75282 жыл бұрын
1:21 looks like you hate that finger isn't it?
@andreykoshelev43912 жыл бұрын
А болгарка не спец приспособление?!. Не выносил бы мозг и правил бы циковкой
@CTPEJIOK752 жыл бұрын
Грубейшее нарушение правил работы на заточном станке
@serhiiserhio93822 жыл бұрын
Главное ролик запилить, пипл схавает!))
@user-bt9ec9xi5f2 жыл бұрын
Карандаш для правки круга стоит на 2021 год около 500рублей. А здесь чтобы поправить круг надо: 1. Болгарка 2.круг по камню 3.пылесос 4.струбцины 5. Какие-то палки Ну да, так же проще..
@user-ow6eu1dj1v2 жыл бұрын
Для карандаша нужен 1.подручник,т.е какие-то палки;2 пылесос, или ты думаешь пыли не будет ;3.струбцина, а как ты хотел - шланг крепить то надо. 4.у домашнего мастера всегда, ну или почти всегда, есть ушмка.
@user-bi8ky1rb9e2 жыл бұрын
Можно пыль глотать..силикоз, всё такое..зато дёшево.
@serhiiserhio93822 жыл бұрын
@@user-bi8ky1rb9e Силикоз от правки камня раз в год? Серьезно?👏🤦
@serhiiserhio93822 жыл бұрын
@@user-ow6eu1dj1v То есть если у меня нет пылесоса, то я не смогу править камень? Логика(с)👏😂
@user-bi8ky1rb9e2 жыл бұрын
@@serhiiserhio9382 вы считаете что вдыхание корборундовой пыли даёт скилл к легочному здоровью? Серьёзно?..
@kellanaldous70922 жыл бұрын
I'm at a loss as to exactly how a wheel can become lopsided, unless pieces were break off
@jameschester39862 жыл бұрын
Exactly never dressed one didn’t know of it both grandpas never did
@kellanaldous70922 жыл бұрын
@@jameschester3986 I could see needing to do some minor flattening if you aren't smart enough to not just grind in the same spot constantly, or if you were using the side of the wheel, which you aren't meant to do anyway (on most general purpose wheels). But this one he did had a huge dip in the wheel that couldnt have been made with the grinder powered on, even if you just jammed a piece of tungsten in there really hard, you cant just wear down a spot without wearing it down along the entire radius. If it jammed hard enough to break a piece out and come to a stop, i suppose that could be it, or if it was a manufacturing defect where part of it cracked off idk lol
@basheb45h192 жыл бұрын
Он правится куском от абразивного круга, держа в руках