How to Easily install Concealed Cabinet Hinges (35mm Hole Drilling & Mounting)

Рет қаралды 215,790

5 жыл бұрын

Here is a deal from the place i work if you are interested! Free shipping PROMO code- JFREE
www.woodworkerexpress.com/
Installing concealed hinges on a cabinet door can be done yourself.#DIY This method requires no jig or template and very minimal tools. Installation of each hinge is virtually the same. These hinges are designed to mount to the back of the door. A forstner drill bit is required to drill the door to allow for the cup hinges. If you are looking to replace your worn out hinges for some nice and shiny Blum hinges, look no further!
Concealed hinge adjustment video:
• How to Adjust Kitchen ...
Links to get what i used in this video:
Forstner bit 35mm- 1 "3/8- amzn.to/2Y7S6Yi
Vix-Bit 5VIXBIT Self Centering Pre-Drill Bit for 7/64-Inch Hinges and #5 - amzn.to/2IDsmxO
Blum Hinges- amzn.to/2x6I8uq
Makita cordless drill- amzn.to/2xcoRHP
Gorrilla Double stick tape- amzn.to/2IZN61z

Пікірлер: 139

@derikmalenda6675 3 жыл бұрын

Definitely need a video about how to actually hand these inside cabients/install the baseplate and get good alignment and angles on the open and close of the cabinet door.

@kevinharris8629 2 күн бұрын

I love you Jason. I was about to buy $300 worth of tools to put up $30 cabinet doors

@jillalvarez7424 3 жыл бұрын

What about the rest of the process to actually install the “pretend door”?

@lriccobena 2 жыл бұрын

Classified.

@lovemetu 2 жыл бұрын

Exactly ! Only half of the job on this video, what about the second half where you are locating the other halves of these hinges inside the cabinet and then finally completing the job by hanging the cabinet door !

@susannolan6292 Жыл бұрын

I agree.. That was the easy part lol

@widearchshark3981 Жыл бұрын

@@susannolan6292 This guy explained it great... And then didn't finish it !

@codykantor 5 ай бұрын

Not subscribing because you didn’t finish the process… would have been an immediate follow if you did

@robertaustralia5852 2 жыл бұрын

the tricky part is fitting the door onto the base. How do you make sure you put the base hardware on in the right spot so both parts align.

@Somong 2 жыл бұрын

I appreciate your cadence of "direct to the point," with a touch of "funny."

@BB-jw6iu 3 жыл бұрын

very good. would like to see the hanging part with adjustments etc.

@karltownsend6020 3 жыл бұрын

Thanks, have to do one of these tomorrow. Don't want yo have to invest in a jig, or make one just for one job. This has helped me out. Thanks mate 👍

@robrobinson8979 3 жыл бұрын

Clear and concise, I too would like to see the next part for hanging the doors.

@robertgunther3080 2 жыл бұрын

Yes, the part demonstrated in the video looks easy enough. Now what is the easy part to hang the doors?

@toomanyhobbies2011 Жыл бұрын

The order of installation and straight edge were very helpful, thank you. 1. measure and drill the holes 2. align both hinges with a straight edge

@chessbully1664 3 жыл бұрын

Short and sweet straight to the point thanks! 👍🏾

@deborahharry7431 4 жыл бұрын

Thanks Jason for your video. I was really worried about doing it myself, but I did exactly what you demonstrated & my concealed hinges are installed perfectly, and without the expense of a jig. I did it; phew. Thank you!

@DoingitWithjason 4 жыл бұрын

Awesome! Way to go!

@harrypowers9412 4 жыл бұрын

This is the best video I’ve seen on installing European hinges-and I’ve watched quite a few! Thanks.

@miguelamartinez8614 4 жыл бұрын

Thanks man you really helped me ,others only give measures in mm.

@timfischer 2 жыл бұрын

Video was great... but you only covered half the problem. OK so now I have one half the hinges in. Next comes the critical alignment into the cabinet box... but you stopped before we got to the part.

@alejandropena4412 2 жыл бұрын

Thank you Jason, I really appreciate your video. It helped me a lot.

@beverlynovak5056 5 ай бұрын

Great explanation! Very easy and good humor! I am a woman learning sone new carpentry skills and this was perfect!

@Albertangelo123 8 ай бұрын

Easy, quick, understandable. Thank you!

@paulgrabowski 2 жыл бұрын

…”and by WE I mean ME” 😂🤣😆 love it. And then I subscribed lol. Keep ‘em coming. Appreciate the humour and honesty.

@oseijoseph3760 2 жыл бұрын

Thanks, it's really helping, you did a great job

@davidbentley6692 Жыл бұрын

Great video quick and easy 👌

@michaelshelton8073 2 жыл бұрын

Thanks for the help. You may want to mention for us to make sure left or right side hinge install.

@JoelFishinAintEasyBusbee 2 жыл бұрын

Love this video. Huge help! Thanks!

@brucebernal65 3 жыл бұрын

Ok you made it simple thanks for not wasting my time

@andrewmorke 10 ай бұрын

Your video was adequate for the purpose. Thanks.

@jeejeeartcrafts1754 Жыл бұрын

Very well done! Thanks!

@Sundardevsaha-e3k 2 ай бұрын

Nope. You don't suck! This was great. Would have loved to see the door hung, but this was great. Thank you!

@rubensboats 2 жыл бұрын

Doing some doors now. The trick with stright stick should really help.Thanks

@paulgrabowski 2 жыл бұрын

Btw, after watching your video, I used your method to install these hinges in a cabinet without spending any money on a “jig”. That would have been a waste of money! Thanks

@walterkemp6558 2 жыл бұрын

Great stuff. Thank you.

@russellkeith3193 2 жыл бұрын

Thx you looks really easy

@bruceli161 2 жыл бұрын

very good explanations

@ModernRemade 3 жыл бұрын

4:50 That trick with the scrap is genius!

@tyrobbins1998 4 жыл бұрын

Thanks for taking the time to make this video. Just installed two cabinet doors that went in perfect using your tutorial. 👊 (I subscribed)

@julyseng5653 2 жыл бұрын

Thank you for enlightenment.

@fredbloggs4829 Жыл бұрын

Apart from the archaic measurement units, this was a great video. The best I've seen which shows how to mount his style hinge.

@tim5111 3 жыл бұрын

Great job !!! Chapeau

@DoingitWithjason 3 жыл бұрын

Thanks

@ecpoirier 2 жыл бұрын

not going to lie. Not looking forward to trying to drill 1 3/8" into Melamine. would love to your tips/tricks on how to install door onto the actual cabinet. p.s. love the relaxed delivery of your message. good camera presence.

@user-kn2pq9sh5s 10 ай бұрын

Loved the video. Now need to know how to properly locate the bracket the hinge locks onto inside the cabinet. Flat wood. No shelf pin holes

@joeguilfoyle1922 4 жыл бұрын

Great Video and right on time. You saved my ass.

@DoingitWithjason 4 жыл бұрын

Great to hear! Was the video detailed enough? I always wonder if my videos have enough details to help people per there experience

@joeguilfoyle1922 4 жыл бұрын

@@DoingitWithjason I thought it had the perfect amount of detail. When I took on this project, I was thinking of using a router bit or a dremel to drill out the hole. I was able to buy the drill bit at lowes for 13 bucks. I was concerned about measuring and keeping the holes centered and square and was just going to wing it :-) You made it simple and easy to measure and keep everything perfect. I have to do it tomorrow. I hope I don't screw it up. I only have 1 shot at it.

@alexgrubb6640 3 жыл бұрын

Thank you

@yvonnevilla4312 3 жыл бұрын

I plan on picking up a vix bit for drilling the pilot holes using the same Blum hinges. How deep do they drill? My cabinet door and frame are from 3/4” plywood.

@stevenoliveri2023 3 жыл бұрын

Ok thank you for that BUT what about the other end where those hinges go into?

@gabriellacaldarone5373 2 жыл бұрын

Great video. I have oak cabinets with exposed hinges. I want to keep the same oak and color. Could I take them off and do this or would it look bad?

@JenniferPerez-zo1ir 2 жыл бұрын

nice job jason with the video I returned the kreg jig and will try it your easy way but i don't see the links.. please advise

@jimc4731 3 ай бұрын

What's an easy method of marking where the cabinet end of the hinge is to be mounted in the cabinet? JIM

@trunorthmusketeer6266 2 жыл бұрын

Great video, was very useful. But now I want to know how to install the mounting plates in the box with just a tape measure.

@maylinrivas9865 2 жыл бұрын

All great and easy but how do you do the other part??

@Mainbusfail 2 жыл бұрын

Okay Jason, how about the second part - mounting plate installation - depth etc. etc. :)

@JenniferPerez-zo1ir 2 жыл бұрын

oops I just found them thanks again!

@alainfernandes2122 2 ай бұрын

Cool video. 👏👏. Is the 7/8 from the edge standard for inset hinges, overlay or half overlay?

@dgalson 3 жыл бұрын

Does the 7/8" inset distance change with 1/2" overlap door, or inset doors? How to determine different inset distances for different door thicknesses and overlay dimension?

@joaquimbabu1098 2 жыл бұрын

I have been wondering the same

@nikopeters9660 Жыл бұрын

Same here

@MomBFF 11 ай бұрын

Same question

@wonderwilds 3 жыл бұрын

Free for all down here, woohoo !

@Ash-xi1hr 3 жыл бұрын

What about putting it on the cabinet

@bobofalltrades7411 2 жыл бұрын

Good video. LOL at 4:25

@Poison13t Жыл бұрын

I need help. 😫 trying to replace all my cabinet hinges because the ones that came with my cabinets are cheaply made. They are snapping. However mine seem like they have some type of riser which is making it difficult for me to chose new hinges.

@UDoIt2 5 жыл бұрын

Nice work!

@DoingitWithjason 5 жыл бұрын

Thanks Regor!

@roynesbitt1973 Ай бұрын

So wanted to clarify. The hinges you measured were 3” down by 7/8” in. Is that standard?

@rmayor64 Жыл бұрын

Cant seem to find a good video of how to actually install the door to the inside of the cabinet. Once the hardware is placed into each side it seems like they have to clip into each other. I find this to be a difficult process, one of mine fell out and I can't get it back in. Ended up removing the top hinge and now I can't get any of the two back on. On most videos you just see the person pressing and they're done. I've tried to press in many different ways and adjust before pressing in different ways but they don't go in. Please help.

@bootsmclaughlin1438 2 жыл бұрын

Its harder to do than you think as i found out a few years ago. So just ordered a jig £30 now its way better...

@hanipbuhay 2 жыл бұрын

New friend Goodluck, full support.

@sokts5422 4 жыл бұрын

you have a universal hinge with no datasheet. how can you tell how much the off set should be? in your case it's an eighth of an inch offset.

@ThePeebsb 3 жыл бұрын

You can go on Blum website they have that many hinges these are on page 98/99

@donaldhealer9954 Жыл бұрын

Thats the easy part, how about finishing the job. The par I wanted to see was the installation to the cabinet.

@grahamreeve5209 2 ай бұрын

Lovely half of a video. What's an inch?

@alyssawatkins2684 2 жыл бұрын

I am wanting to make my own doors and drawers. No design or routing work, just plain and I will paint them. What kind of wood do you suggest? Plywood?? I know I will have to sand quite a bit

@DoingitWithjason 2 жыл бұрын

Yes a furniture grade plywood would work great! You actually will not have to sand much at all.

@ranahansafurniture9323 4 жыл бұрын

Get need how many inch egged side?

@CPAULINO5347 2 жыл бұрын

Hey Jason, this is only half of an installation, what about the other side of the hinges? My door ended up with gap.how you measured the hinges inside to avoid gaps or overlap?

@christophermclaren6119 Жыл бұрын

Flip the hinge with the mounting plate up,,then measure from the door to the centre of the mounting plate,,usually 30mm,,but come back a few mm to,28mm,,and mark where the holes are going,(drill the holes with the screws for the mounting plate) take the mounting plate of ,and centre it on your marks and screw to the carcass ,then spring the hinge onto the mounting plate,,( best try a trial run first on a scap piece, ),,hope that was helpful,,👍🏴󠁧󠁢󠁳󠁣󠁴󠁿👍🏴󠁧󠁢󠁳󠁣󠁴󠁿

@duelette 3 жыл бұрын

The hard part is hanging the other part of the hinge! Otherwise nice video.

@colinmatthews7541 4 жыл бұрын

how do you fasten them to the cabinet in the right place,do you need a jig ?

@DoingitWithjason 4 жыл бұрын

What I do is hold The door and the proper position with the hinge against the cabinet and carefully open the door and make a mark on the bottom of the plate. This works really well to get a ballpark measurement and make a spacer that will hold the hinge along with the door in the proper position to screw it in.You can also go by the manufacturers recommendation of where to put the holes but depending on if it's insane overlay etc Just seems to be the easiest way to at least get one especially when you have like 20 more doors to do after the fact.Thank you very much for watching this video I really appreciate it and I hope this helped please let me know if you have any more questions.

@JoeMcFarlanesgoogle 4 жыл бұрын

Doing it With jason I was also only looking for guidance on how to align the holes on the cabinet itself. The doors seem easy, it's more a matter of having the right tools. Aligning inside the cabinet seems trickier and more worthy of a video IMO

@cheeryble 6 ай бұрын

You said you would bring your measurement out "about" 7/8 inch. I'm about to fit HOME half overlay hinges. Is there not a definite distance to mark from the edge for each make of hinge? The packet my hinges came in has no measurements diagram, but only mentions the 35 mm for the cup. Thanks very much

@piniped 5 ай бұрын

Same here! No diagram, so I have to guess? I think I'll mock a cabinet next to the frame to mark and measure the correct distance from the edge.

@cheeryble 5 ай бұрын

Ah well it got done..gonna do a corner double door next....bloody expensive Hafele

@papachef52 3 жыл бұрын

So.... now, what do you do with the door??

@markpynduss5073 4 жыл бұрын

Jason for the price of the 2 bits you recommend you might just as well buy the jig kit. it is 2 dollors less.

@DoingitWithjason 4 жыл бұрын

Oh! Good deal! I didn't realize they had a kit!

@tpcolson 2 жыл бұрын

A significant part of this video is missing: how to line up the hinge mounting plates to the frame and actually mate the hinge with the plate where everything lines up correctly, so the word "install" in the video title is a bit misleading. Is there another video that completes the installation?

@blueputtee 2 жыл бұрын

When you open the package the first thing you do is find the nearest garbage can and dump the philips head screws into it and get some screws with robertson head and save yourself some trouble with installation.

@seanadb 3 жыл бұрын

Great video, Jason. Like Harry Powers, I have seen many videos on installing these hinges, most of the time using jigs, but yours was the best, by far. It shows jigs aren't really necessary at all(maybe if you make them en masse they'd be useful?). Liked & subscribed. Also, you may -- mayyyy -- want to give links to Amazon products in different countries. I can't use your link as I'm in Canada. Cheers!

@DoingitWithjason 3 жыл бұрын

Thanks 👍

@Lakkanathunga1 2 жыл бұрын

Appreciate

@joes.5077 3 жыл бұрын

Is that Mr. Swirly behind you from "Pete & Pete?"

@dennisdye2330 3 ай бұрын

What about mounting it to cabinet..

@ginawinter5493 3 жыл бұрын

Ugh. What about the other part? I’m only half done now😩

@stevenoliveri2023 3 жыл бұрын

LOL I just asked the same question.

@stevenoliveri2023 3 жыл бұрын

kzfaq.info/get/bejne/edl0pL14tq6ceX0.html This a video on the other half of the hinge he forgot to show us.

@paulc3960 3 жыл бұрын

Gina & Steven I am asking the same. If can't do the other part correctly, we know what will happen.

@rokman0075 Жыл бұрын

Where is the rest of it? How do you hang them!

@kenz.1977 3 ай бұрын

❤

@kwstasber9190 Жыл бұрын

give the numbers on cm too and it would be great if you conected the door to other scrap wood

@Alamodem 2 жыл бұрын

What about hanging the door?

@glennanderson8981 Жыл бұрын

That was the easy part, now show how you attach the hinges to the cabinet please.

@FroGGi1989 Жыл бұрын

4:25 haha I saw that! xD

@tcarpo1 2 ай бұрын

Why work in inches?

@Acanders1980 Жыл бұрын

You only completed half of the hinge install.

@ysyang1111 4 жыл бұрын

轉速太高了

@brucebondi6104 3 жыл бұрын

It would be helpful to see you install the second part of the hinge, But you knew that????

@yawnastyfpv6942 2 жыл бұрын

Good info, but You hold a pencil funny and I can’t unsee that

@tannerlee4639 4 жыл бұрын

Get a Kreg jig so much easier!

@DoingitWithjason 4 жыл бұрын

I have a Blum mini press, even easier!

@ZkaAnimation 3 жыл бұрын

We see that drill bit fall out ;)

@baigsaba 4 жыл бұрын

Why this video is incomplete. How to install plates? You never told this secret

@lovemetu 2 жыл бұрын

Only half of the job on this video, what about the second half where you are locating the other halves of these hinges inside the cabinet and then finally completing the job by hanging the door !

@PenguinDad0007 2 жыл бұрын

You only showed how to install half of the hinge. :(

@johnsmith-fz3qk Жыл бұрын

Peter Millard

@mrneilram Жыл бұрын

Why don’t you show it installing it on the cabinet too plz

@blainederouen9977 3 ай бұрын

So why not show the whole process. Finish installing the door on a cabinet.

@charleschi843 9 ай бұрын

...and mounting....

@mikestoveken Жыл бұрын

Great no-jig video! This video plus this one by Rogue Engineer: kzfaq.info/get/bejne/bp6JedeAzJiZfZc.html which shows how to mount and align them inside a cabinet, would be the perfect combination of videos for doing the complete installation without a jig.