How To Easily Replace Hustler Raptor SD Hydro Pump Drive Belt On Zero Turn Mower Model 932566

Рет қаралды 69,866

Жыл бұрын

Thank you for watching!! If we helped you out and you want to show your support - LIKE, SUBSCRIBE or give us a shout out below. If you saw something you didn't like leave your comment below as well, these things help us get better!
To see our recommended tools and products visit our Amazon shop at www.amazon.com/shop/individua...
We show the step by step process of changing the ground dive belt on this Hustler Raptor SD zero turn mower model 932566.
The belt part number 603907R (607400) can be purchased at amzn.to/3uNAV3n
This is one of the easier belts to replace and with these steps you can do it in a matter of minutes.
From start to finish this repair (without recording a video) would have taken me less than 15 minutes total.
It is made a lot easier by the design since you do not have to remove the PTO clutch in order to replace this pulley.
Like and subscribe to see more helpful videos like this one! Save some money by doing it yourself!
#hustler #raptorsd #smallenginerepair #individualizedrepair #smallbusiness #diymaintenance
About Us:
My name is Martin. I have been repairing tools and small engines for almost 20 years. We operate a small engine repair shop in Illinois. We service / repair Briggs & Stratton, Kohler, Kawasaki, John Deere, Cub Cadet, Toro Tecumseh, Loncin, Honda, Craftsman, Husqvarna, MTD, Troy Bilt, Simplicity, John Deere, Exmark, LCT, Generac and many more brands. We work on riding mowers, walk behind mowers, snow blowers, zero turns, generators, pressure washers and much more. We normally repair about 3,000 pieces of equipment every year and look at many more that are beyond an affordable repair. Hopefully our videos will save you some money and give you the information you need to work on your own equipment or figure out the issue at hand.
Disclaimer: Links included in the description are affiliate links. As an Amazon associate we earn from qualifying purchases. There will be no additional charge to you for purchasing here. We appreciate your support, which allows us to continue to provide original content!
Please be careful when repairing any piece of equipment and follow all possible safety measures. This video is for entertainment purposes only.

Пікірлер: 77

@docjody8624 9 ай бұрын

Word to the Wise! DON'T remove beastly Deck Belt Spring. Save your time & fingers by following method shown in this video instead. Genius. God bless.

@IndRepair 9 ай бұрын

Good info! Thanks for watching!

@shaneerdley3218 Жыл бұрын

Watched 3 other videos yours was the best and appreciated the video mower is up and running in less than 30 minutes

@IndRepair Жыл бұрын

Awesome! Thanks for watching!

@puntacanaman1 8 ай бұрын

Excellent instructions here. You actually showed the installation. Some guys out there just show the new belt in place. One even insisted that the blade belt didn't have to come off. Guess he uses magic. LOL.

@IndRepair 8 ай бұрын

Haha that's a new one!! Thanks for watching!

@LawnJohn 10 ай бұрын

I watched a few videos on this, but you did the best job, not over complicating it. Thanks for sharing!

@IndRepair 10 ай бұрын

Glad to help! Thanks for watching!

@TheReginold 4 күн бұрын

Thank you.

@IndRepair 3 күн бұрын

Thanks for watching!

@viktorloewen77 15 күн бұрын

Very helpful. Thank you very much.

@IndRepair 15 күн бұрын

I am glad to help, thanks for watching!

@mambajeep2585 2 ай бұрын

Unreal how easy you made this, I did however have to take off the deck spring because of the deck belt being too tight. So in total 12 mins from start. Thanks!!

@IndRepair 2 ай бұрын

Awesome job! Thanks for watching!

@paulinkansas 10 ай бұрын

Thanks, you saved me much time and more gray hair.

@IndRepair 10 ай бұрын

Glad to help! Thanks for watching!

@sonnyphakonekham 9 ай бұрын

Thank you, had my hustler few months and belt came lose! Fast n easy fix!

@IndRepair 9 ай бұрын

Thanks for watching!!

@kennyhickman4678 15 күн бұрын

Take a ratchet strap and pull that poly back a little bit and you can easily remove the deck belt from the motor

@IndRepair 15 күн бұрын

Definitely one of my go to's for installing tough springs. Thanks for sharing!

@cityguyinthecountry Ай бұрын

Thank you. I literally had to do this today - you saved me!

@IndRepair Ай бұрын

Glad to help! Thanks for watching

@fideauone3416 Ай бұрын

Just put one on a 5 year old Hustler 42 in. cut. Be advised that the new belts may be a little wider and harder to put over the pullies. Really had to work hard as it hits the top of the frame and takes a lot of pushing to get it in. Also there is a skid plate I had to take off to be able to reach the pullies. Had to remove the bracket that holds the PTO clutch. It's not as easy as he makes it look. Took me over 2 hours but I could not have done it without this video.

@IndRepair Ай бұрын

I have never seen one that the bracket or pulley had to be taken off but thanks for sharing this! If I get another one in this style maybe I will do a remake. Glad to help

@DanmarkElectrical Ай бұрын

Great video, much appreciated

@IndRepair Ай бұрын

Glad to help. Thanks for watching!

@Woodyballer Жыл бұрын

Much obliged. It made it extremely easy to complete this. Thanks!

@IndRepair Жыл бұрын

Glad to help! Thanks for watching!

@albuechele8089 Ай бұрын

Thanks for sharing!

@IndRepair Ай бұрын

Glad to help

@lisajulson8847 Жыл бұрын

This video was very helpful. Thanks for sharing the information. Saved me a lot of time.

@IndRepair Жыл бұрын

Glad to help! Thanks for watching!

@ericsantelli7259 9 ай бұрын

So far so good. Only used it once, but...

@IndRepair 9 ай бұрын

Glad to help! Thanks for watching!

@brandonflees5678 11 ай бұрын

Great video, thanks for posting!

@IndRepair 11 ай бұрын

Thanks for watching! I appreciate that!

@MrTrentjay 5 ай бұрын

Thanks for the video, I just use a bit of bruscutter cord to pull the springs loose or back on 👌

@IndRepair 5 ай бұрын

Good tip! Thanks for watching!

@weldonlangley245 5 күн бұрын

Great video. Used the info in it today when replacing the hydro drive belt on my Hustler Raptor SD 60 model 935916. Made the replacement very easy. Thanks for sharing your time and knowledge. Have watched several of your other videos especially the one where you gave us a tour of your shop. Just turned 74 yrs young but getting down under my mowers and ATV's to work on them and then getting back up and vertical is getting more difficult every year. Really interested in knowing about the drive-on lift you use. Where can one be purchased or did you build it? What's the good and bad about it? Any info you can share would be greatly appreciated. Thanks in advance and PLEASE keep providing those great videos you generate. The thoroughness and quality of your videos are the best I've seen.......anywhere!!!

@IndRepair 3 күн бұрын

I appreciate that! My back was horrible (still is sometimes) until I got these lifts. I have multiple lifts there is a video at kzfaq.info/get/bejne/Y85-gZVyrNizeJ8.html showing the two we have currently. We just got one in Friday so there will be an update video comparing these two with a little heavier duty one we just bought.

@IndRepair 3 күн бұрын

I appreciate your words of support

@FM2191 Жыл бұрын

Best video on this! Thanks.

@IndRepair Жыл бұрын

Thanks for watching!!!

@tylerfoland9335 2 ай бұрын

Helped me out, thankyou

@IndRepair 2 ай бұрын

Glad to help! Thanks for watching!

@philliphall5198 Жыл бұрын

Thank You for information and advice

@IndRepair Жыл бұрын

Thanks for your positive support and for watching!!!

@donmayberryjrsOPE Жыл бұрын

Some great advice!

@IndRepair Жыл бұрын

Thanks for your positive support and for watching as always Don!!

@user-wc4zy5lb1m 6 ай бұрын

Thanks bro

@IndRepair 6 ай бұрын

Glad to help! Thanks for watching!

@keatonking2298 3 ай бұрын

Thank you! 🙏🏻

@IndRepair 3 ай бұрын

Thanks for watching! Glad to help!

@sanesociety-oo2ym 2 ай бұрын

There is an electric plug of some kind preventing access to the pulley. The one in your vid is on the back of your pulley where as mine is on the front side and the wire is blocking me from installation. Is that connector a plug or is that a fixed connection?

@IndRepair 2 ай бұрын

There is an electrical connection where it can be removed either right at the pulley or up the wire with a plastic connection

@steveriggenbach90 Жыл бұрын

A LOT EASIER Lol. then on mine Thanks for earlier showing tips on getting a drive down.

@IndRepair Жыл бұрын

Definitely one of the easiest! Thanks for watching!

@philliphall5198 Жыл бұрын

Same one before Like the one you’ll got

@philliphall5198 Жыл бұрын

Sorry not for you’ll

@IndRepair Жыл бұрын

Nice!

@Art-jl6pt Жыл бұрын

Hi I ordered jd140 but returned because it didn’t have cruise control so I ordered cub cadet XT1 46” 23 hp koler- hope you work on one and post all related repairs for it- thank you bud

@IndRepair Жыл бұрын

Have worked on plenty but there will be more to come I am sure! Thanks for watching!

@weldonlangley245 Ай бұрын

Great video and thank you sir for sharing your time and expertise . I have a damaged transmission blower fan (rear right side) and will be replacing it when parts arrive. My mower is a 2016 Hustler Raptor SD 60" model #935916. VERY little clearance between top of drive belt pulley and solid metal above it. Almost no clearance so it looks like I will need to drop the transmission down some to access the nut that holds the pulley and fan on the transmission shaft. Since the pulley looks to be in good condition was going to replace the fan only ($17) rather than replacing with the fan/pulley kit ($67). Any suggestions / recommendations regarding fan only vs fan/pulley kit? Also any suggestions / cautions about gaining some clearance by loosening off on the transmission mounting bolts? I've looked at your video play list and didn't find any video of yours regarding fan replacement. Anyway, any advice you could share would be greatly appreciated. Thanks in advance !!

@IndRepair Ай бұрын

Yeah, just drop it down a bit and you should be able to get it replaced without issue. Just replacing the fan is fine if the pulley is good, no need for the kit

@AHomeownersBestFriend 2 ай бұрын

Is there a way to lower the fan /pulley??? There’s like no space between the pulley and the bottom of the deck 🙃

@IndRepair 2 ай бұрын

Can you drop the deck further down? Talking to main pto pulley?

@ShanePresleyC 9 ай бұрын

Any advice for how to lift the backend once the belt has slipped and the whole thing is immobile? I can't get under it enough to finnagle those belts and springs

@IndRepair 9 ай бұрын

It sure is difficult without some help! A jack and some jack stands or ramps to prop the back up will do you wonders for access

@danne941 Жыл бұрын

Just found the channel and enjoy the content. Which mower do you recommended for .75 acres and under 3k? Thanks!

@IndRepair Жыл бұрын

Doesn't seem like they exist anymore...Home Dept last week had Toro Timecutter at $3,299...

@drewbush6535 Жыл бұрын

👋👍

@IndRepair Жыл бұрын

Thanks for watching!!

@patrickarter8772 Жыл бұрын

@IndRepair Жыл бұрын

Hello

@sherrischneider2794 Жыл бұрын

Mower needs a good cleaning. Blow off all that grass and dirt with a blower please. Makes the job so much nicer

@IndRepair Жыл бұрын

Very little grass on it compared to most but it was blown off before sending back. One cut and that grass gathered back in the same spot though, I'm sure. We also did a tune up on it after this belt replacement. Thanks for watching!