DIY - save money and Do It Yourself. Here is a video explaining a full tear-down and repair of the high pressure pump. KÄRCHER K5 and similar models. Buy parts online: www.kaercher.c... #DIY #kaercher #pressurewashing
Пікірлер: 63
@MikeyDTriesАй бұрын
I discovered this video one week after buying a new jet wash, but on the plus side I am now going to buy the parts for my k5 and repair it so I always have a back up. Great video and thankyou for the information on how to replace the parts
@gwennie12632 ай бұрын
Thank you. I followed your instructions and nothing happened fir about 15 minutes. I told myself this is the last time I'm taking off the hose and it kicked in. So happy and thanks again 🎉🎉🎉🎉🎉
@SuperMistag10 ай бұрын
I had a pressure issue on my K5 and was debating fixing it myself or sending it in to a nearby Karcher service centre. The video was useful in showing that it takes quite a bit of time to disassemble, fix and re-assemble. Based on that, I decided to send it in for repairs. Turned out to be a good decision with the overall repair bill being comparable to the time I would have done it manually in. It also really helped in understanding the explanation given as to the failure on mine (piston stuck) and confirm how it all works together. Thanks!
@biglebowskee Жыл бұрын
Finally found a video with useful information on how to fix this. Thank you sir.
@anthonyscuderijr.cluchfc6602 Жыл бұрын
Outstanding video. Very well done. Thank you for this! Having just bought the K5 over the K1700 and Ryobi 1600 I found this helpful in understanding how it is built and repaired!
@e9999qwe Жыл бұрын
Neat to see the inside of that unit, thanks for the vid. FWIW, I always use a lubricant for Orings when installing them. It helps to make the installation easier with much less friction, and reduces the possibility of damage to the Oring (pinching, scraping etc). Probably helps with waterproofing and durability too. Try silicone grease sometime.
@stephenfielding71652 ай бұрын
Great video, head and shoulders above most of the other karcher videos on here.
@andrevdw7476 ай бұрын
Thanks for this helpfull video and the support link. With that I fixed my K5 myself instead of paying euro 200,- fix costs. The pressure pipe was broken. Also cleaned the pump house and changed the oil 👍🏻
@frenkc13 ай бұрын
Do you remember how much oil you put in? And did you remove the grease that was in there? Thanks in advance
@andrevdw7473 ай бұрын
@@frenkc1 I completely cleaned the chamber as I saw also water drops inside. I filled the chamber only with oil little above the top level of the concentric ring which moves the pistons. Please know that is more guessing. I didn’t checked the official amount of oil with Karcher, nor the grease which I didn’t placed back. Hope it helps.
@rcizmek5 ай бұрын
I used your video as a reference to replace pump head. It is very usefull and detailed. Washer works like new one. Thanks!
@fernandop.38839 ай бұрын
thank you for this video, I'm repairing a similar one and this was very helpful!!
@ΑΝΤΩΝΗΣΑΝΥΦΑΝΤΗΣАй бұрын
Great video i am glad you fixed this machine.is quite common problem in this machines the cause of the problem is when you're doing a lot of start and stop with the trigger the next time you open the pump put out pressure piston on off clean it and put some silicone grease
@Bullfinchman15 ай бұрын
Fantastic video. Thank you
@meteora8888 Жыл бұрын
Excellent. Thanks for the good quality video and explanations. Will try repairing mine which only seems to max out to medium pressure on my k4 full control.
@noonefalls313 Жыл бұрын
Thank you for this video. My Karcher is slightly different but your detailed process of taking apart and putting back together was very helpful. As you say, I fixed my machine for 1/5 the price of a new machine. considering it is only a small part that was broken this seems expensive but it is still better than buying a new one. The biggest pain was waiting for the part to come in the mail to be able to put it all back together.
@jocl8488 Жыл бұрын
Nice helpful video. But I think it would be much recommended, to remove the old greace (and cleaning all parts) before filling up the oil. Mixing up greace and oil never is a good idea in general. Even less already used contaminated grease and new oil.
@chaproo123453 ай бұрын
Thankyou , I managed to fix mines with the help of your video.
@robbarthram7418Ай бұрын
Excellent video and information. Very helpful thanks
@dermotevans2064 ай бұрын
Many thanks , you have saved another K5
@catsarereallyfurryaliens2 ай бұрын
I recently repaired the next model up from this which has the hose reel in between the handle, I replaced the capacitor, the hardest part of the whole procedure was rooting those pipes in the correct positions before closing the case up I lost a lot of sleep over this I reckon I took a total of 16 hours over a few daysBut it was worth it
@kaikruner697111 ай бұрын
Good video and good explanation, thankyou very much
@wiesawkawecki64704 ай бұрын
Bardzo mi dzisiaj pomogłeś przy składaniu Karcher K5, dzięki
@ignassongaila4229 Жыл бұрын
Man, you saved my day. Great👍
@NicovonWielligh Жыл бұрын
Great video, thanks
@LiamWall-mu9kx9 ай бұрын
Brilliant thanks very much
@BHANGUVIDEOSUK Жыл бұрын
Great video.
@gg5685011 ай бұрын
Got a non functionning one for dirt cheap, glad i saw the video hahaha
@buck36553 ай бұрын
I'd Be Inclined To Wet The Gasket Seals With Some Oil For Assembling
@ava7lancheАй бұрын
thanks mate 👍
@deanwarner20066 ай бұрын
Pump heads are notoriously weak on Karchers, 9/10 it's this part that fails, tell tale signs are reduced output pressure or the unit starts pulsing as the pressure keeps fluctuating
@ctackney1 Жыл бұрын
A great video. A pity that Karcher thought that a plastic part was capable of withstanding over 2000psi for any appreciable length of time.
@micdev424 ай бұрын
That appreciable amount of time is Karcher’s guarantee period. After that they could not care less. The replacement pump head on my K4 was £65. I could buy a new K4 for £130, so I chose not to repair.
@MikeK-NIreland4 ай бұрын
Because that's how they design in failure after a period of time which means you go out and buy another.
@buck36553 ай бұрын
It's A Poor Effort Really Using Plastic Components
@wadejarvis-im9mj2 ай бұрын
Thanks great gide😊
@robinmills340427 күн бұрын
Handle snapped on my K5. It incorporates hose reel. Any info on how to remove and replace hose reel into new handle?
@vidarsandvik38052 ай бұрын
Bra video, ikke samme feil på den meg fikser. Må skifte samme del. Go teardown. Setter pris på at du har laget denne🙂
@sburly29719 ай бұрын
I’ve got a K5 compact. It’s a couple of years old. Not been used much. When you first switch it on it works fine. Motor sounds healthy, plenty of power. As soon as you release the trigger and then re apply the trigger it stops working, no pressure. If you disconnect the hose it immediately fires up and pumps water out of the hose. Reconnect the gun, works fine until you release the trigger again and then no pressure. Very annoying. I took it apart and everything looks fine. Any ideas?
@sandorpasztor7086 ай бұрын
Hello.I have the same problem.Can you told me whitch part must replace?
@V0LKSJAGER4 ай бұрын
Just don't use the dirt blaster. Set the lance to soft before pulling the trigger again. Switch of the machine, set lance to soft, pull the trigger and turn on the switch simultaneously. This is a temp fix, my 14 yr old karcher k3.550 is acting like this.
@vinkel44 ай бұрын
Probably air lock. Remove handle and turn off power and leave the water running for at least 5 minutes to remove all air from inside pump and hoses. Then put handle back on and turn on power. That should do the trick.
@gbdjski2313 ай бұрын
I have the same problem on my K5 pressure control. If I pull the trigger and hold and then turn the washer on it works with full power. If i release the triger and pull it again, the power is very low. If I repeat the same - pull triger, turn it of and on again - full power. I dissasembled the unit, inspected the pressure head and everything seems to be fine, nothing broken. Anyone has any idean what could be wrong? Its not an air lock, when it starts it has full power and can go full power all time until I release the trigger..
@gbdjski2312 ай бұрын
Follow up - i took apart my K5 and found the piston at water inlet stuck. I pulled it out with pliers, greased the seals with silicone grease and cycle it in and put with pliers until it moved freely. It works like a charm now!
@user-xi3gm4bf4d Жыл бұрын
Thanks for informative video. Just wonder how you remove the big bolts on the pressure chamber. I am not able to remove the 4 skrews on mine. It’s almost as they are glued.
@techandfun7723 Жыл бұрын
Try some WD40 or CRC 5-56 for some hours and see if it helps. I used a Makita Impact driver very carefully. I don't think they are glued, but corrosion may be holding them things. Good luck and thanks for the feedback 👍
@fernandop.38839 ай бұрын
a little heat "nothing more than a air-dryer" sometimes helps
@raziackzing7 ай бұрын
Superb....
@AhamdLotpi17 күн бұрын
🎉i want to bay part of model k5
@tonyburgmeier8153Ай бұрын
What are we fixiing? When the unit doesn't power on? That is the problem I have with mine.
@niklasnorberg6106Ай бұрын
try hot wiring it around the switch, if it doesnt power on, the motor is broken.
@harold12A Жыл бұрын
Mine is 110 volts. Can i change the power supply to 220 volts? We use 220v in my country so for now i can only use it with a 5000 watt step down transformer. But if i can change the power supply then i can plug in mains power directly. Any help or advice?
@nellytaderera3 ай бұрын
Am watching from Mozambique my machine have same problem how can I get this part all white Valve are broken
@pawspaws1015 ай бұрын
I have a K6 which looks similar, cant take wheels off as the locking washers on axle you cant bang out as they grab more. But the two holes in wheel hub appear empty plastic, as no screw head, tested with magnet too. So dont think its that. have removed all screws I can see, but top yellow/blackcover just will not budge. Anyone taken a K6 apart??? I've given up for now as will break plastic housing..... Ta
@alanreynolds2125Ай бұрын
hi, motor oil not grease?
@patszyba885 ай бұрын
Witam. Posiadam myjke Karcher k5 myjka działała normlanie lecz teraz gdy właczam slychac przygotowaniendo pracy natomiast po naciśnieciu pistoletu brak rekacji. Jedynie dziala gdy pistolet wcisne i włacze to wtedy jest oki. Jakies sugestie?
@antoniosanchezfra4 ай бұрын
👍
@user-zw3bg9vr5g6 ай бұрын
How to fix Karcher k5 can’t get lance to connect to handle?
@chloeleedow72502 күн бұрын
These things are actually that shit, I have a k5 and lol at the premium on the thing. My garden hose has more pressure on its own.