Dude! Thank you for this video, I went to the hardware store and grabbed a $2.50 key blank and it freed up the cylinder! I was ready to drill it out, you saved me big time. I appreciate the content!
@JoJo-Mo-63 Жыл бұрын
thank you so much for your video! I followed step by step your instructions and fix my truck ignition lock today. I can't thank you enough. Keep up the good work.
@ColetteOlivieri3 ай бұрын
😂😂😂 The first option using another truck key to reset the tumbler worked on my 2005 Tundra with a 2007 Tundra key. You are a magician🎉. Thanks💙
@bpd3462 ай бұрын
Thank you for posting this! I just replaced the cylinder and it was very helpful 👍🏻
@yortola Жыл бұрын
Super helpful! I did exactly what you did and it worked like a charm! TY!
@gregorymiller49055 ай бұрын
Thank you! I dont have a blank but I used my door key, stuck it in and tried to turn it, that didn't work but when I tried the ignition key again it fired right up. Awesome video! Got me out of a bind. Thank you.
@joserivera9191 Жыл бұрын
Thank you so much. I was about to call a lockman until I watched this video. I was able to fix the problem in about an hour!
@thomasmccullough42189 ай бұрын
Dude. It worked. You're a lifesaver
@kyleruud5094 Жыл бұрын
My 04 just started snagging and getting hard to turn. Thanks for the lifesaver vid
@kyleruud5094 Жыл бұрын
Fixed it in an hour, 04 was slightly different. 2 of the 3 faceplate pins were exposed and lifted out with a pick. Drilled straight through the top one that is hidden and it popped right off. And watch out for the bar lifter peice. It's just sitting at the front and falls right out. Thanks again Ogre. Killed it.
@boyfromdabayou11 ай бұрын
Thanks for the video. Although mine was made slightly different i was able to get it apart. saved myself hundreds...Thanks
@robertobarrios8479 Жыл бұрын
you are the man!!!! thanks for the video helped me a lot
@blankreg363911 ай бұрын
Great detailed repair video. Thanks!
@tomlambert80312 жыл бұрын
smart man works like a charm thank you!!
@anthonygasparini1734 Жыл бұрын
Great video thank you! Just did the same mod to my lock!
@BMWDamun Жыл бұрын
The little wedge that falls out lifts the steering lock arm so the key can go to acc or ign. Learned that one the hard way. Carquest CSC 1426 is a relatively inexpensive replacement for the whole deal.
@johngalan3754 Жыл бұрын
Just curious, how did you settle on this one? Like you replaced the OEM one with the CSC1426 without any issues and the dimensions were the same?
@Steven-gv1ke9 ай бұрын
2005 Tundra with auto 4.7L requires CSC2541 lock cylinder.
@john-glennrivers9591 Жыл бұрын
That worked! Thank you.
@johngalan3754 Жыл бұрын
Something to note, I removed my ignition lock cylinder and did not have a place where I could drill out the pin. Its possible my lock cylinder was replaced in the past and it's a different model type, but if you try this it would probably only work on an OEM one. Either way, clever and effective
@ferra17022 ай бұрын
Gracias por este video 👍
@dougswanson1636 Жыл бұрын
The blank key in the ignition lock cylinder as stated worked. It allow me to start the 04 Sequoia and move it to be repair.
@bradleyr4451 Жыл бұрын
Do you know how to disable the LOCK of the steering wheel itself? someone used the truck and didnt know it had to be in PARK to take out the key, they ripped the key out with the selector in D. now its ruined where you can start it and take the key out and it runs. but now? Im told the steering wheel is locking up while driving and thats bad. Im used to older Fords, Chevys not these early 2000s Toyotas. Rather take the steering lock mechanism out completely and fix later to avoid crashing, its a daily driver. Any ideas appreciated.
@MikeS-rg9zt6 ай бұрын
This video is a life saver!!!!!! I thought you were full of shit but holy fuck it worked
@jwint563 Жыл бұрын
So after you pound out those rivets and pop that pin out is the snap ring the only thing holding the unit all back together?
@OgreMoto Жыл бұрын
So, if I recall correctly, yes, the rivets hold the face of the lock on and the snap ring holds the core innards into the sheath. After those are off, it should come out easy.
@tvpierce15 күн бұрын
With the rivets pounded out, how did you secure the face when reassembling?
@OgreMoto5 күн бұрын
@@tvpierce1 just pushing it all back together is enough to hold it.
@gfoxer10 ай бұрын
Great tip but I wish you had shown the rivet removal and even more importantly what you replaced them with. Screws? Rivets?
@OgreMoto10 ай бұрын
I didn’t replace them. I just loosely fit it together and once the kick panel goes back on it held everything together.
@josephguite1580 Жыл бұрын
Struggling to tackle this now, & noticed I have a lone small grey wire in the zip ties around my key cylinder. Anybody know what it’s for? Mine’s been snipped
@jntzcamacho10010 ай бұрын
That's the wire to hold up the bottom of the steering wheel part you have to detach in order for the whole assembly to come off. Includes taking the screws off too with 10mm .there are videos up on KZfaq on how to unattach that wire the correct way
@mtsanchez273 ай бұрын
If replaced with a new ignition lock cylinder needs to reprogram the key?
@OgreMoto3 ай бұрын
The new lock cylinder will come with a new key. There’s no programming keys on these trucks only cutting. They’re actually very easy to get started without a key if you know what you’re doing.
@mtsanchez273 ай бұрын
@@OgreMoto great thanks
@cesargallardomartinez20813 ай бұрын
gracias gringo ...me salvaste ....saludos desde Chile
@nikoridge21329 ай бұрын
I took the snap ring off, got the rivets out, and took the pin out. The face still won’t come off though and the lock cylinder won’t come out either.
@OgreMoto9 ай бұрын
Make sure you press down on the tail to release it. I show it somewhere in the video just can’t remember where.
@timsmith315820 күн бұрын
Do you have to drill out the rivets?
@poopydoody76185 ай бұрын
My key is stuck to the point where it can't even move to acc, how would I get it out, I've been drilling for 10 minutes with no avail
@OgreMoto5 ай бұрын
If your key is that stuck, really the only solution is a whole new lock cylinder unfortunately. Either that or find a way try tapping it with a hammer to try and free it.
@OgreMoto5 ай бұрын
Or you could try and get some kind of lubricant in there.
@poopydoody76185 ай бұрын
@@OgreMoto thank you I will try this out
@porkchop3094 Жыл бұрын
How about putting the phone on a stand and show the process using both hands and a steady picture?
@OgreMoto Жыл бұрын
Nah
@Steven-gv1ke9 ай бұрын
How about you just say thank you for a video he didn't have to do, and literally took the time to post on here to help other people out of the goodness of his heart.
@Steven-gv1ke9 ай бұрын
@@OgreMotothanks for taking the extra time to make and post the video bro! It helped a lot!
@BdaSecureLife Жыл бұрын
Hey man. Can I remove all of the wafers? Will it work
@OgreMoto Жыл бұрын
Yes, it will work, but there’ll be no security and you’ll be able to start it with a Flathead screwdriver.