Jake shows us how to get those pesky rascals seated right, and check out our bridge pin selections here: store.banjoben...
Пікірлер: 33
@astonergamez78424 жыл бұрын
Second day with the my guitar and this happened...Thanks for the fix
@tavidavi83863 жыл бұрын
Same!! It was literally the second day for me aswell 😂
@conchitogarcia779129 күн бұрын
Thanks for the tip. I have a 12 string that is all wonky. Gotta fix several uneven pins.
@yettielusive33705 жыл бұрын
That's a great idea to shave it off the pin. Thanks!
@mahirbirman6659 Жыл бұрын
Bcbh,tjj
@gabestorm7150 Жыл бұрын
Thank you very much Ben, your video was extremelly helpful for me right this minute since I had the same issue replacing the strings on my acustic guitar.
@AndySalinger33 Жыл бұрын
Excellent fix! Much obliged! 🕊
@thatdudefromthefuture3346 Жыл бұрын
Oh god thank you.. bought new pins and I was like did I f*** it up thank you :)
@johnanderson27 Жыл бұрын
Thank you finally some told us what to do 🙏🏻
@nannanaya_3 жыл бұрын
my bridge pins are too hard to remove (i was changing my strings) what do i do?
@toddwilliamson26517 ай бұрын
Stick your hand inside the sound hole and pop the pins up from the bottom! Be careful not to dislodge any wiring if you have a piezo or something.
@jessedavis23513 жыл бұрын
Reaming the holes would be a better fix but does require a speciality tool.
@Anmati135 жыл бұрын
Great video, thanks
@SD-sj2qz4 жыл бұрын
Why does the bridge pin lift ? I have a similar problem in my guitar for the E string
@gigachad22764 жыл бұрын
Same
@socialmeaslesinpartnership125210 ай бұрын
Too small.
@werrylipi83282 жыл бұрын
Thanks for the video sharing..👍
@MurdaMetz2 жыл бұрын
What’s the max amount that’s ok for the bridge pins to be sticking out a little ? Is 2/16 to much ?
@nobrain89632 жыл бұрын
Mine is sticking a little but I don't know it's emergency to fix it ASAP or not
@SethHolmes Жыл бұрын
@@nobrain8963 Martin ships guitars with the pins sticking up a bit. That allows for them to continue fit as the bridge pin hole wears bigger.
@socialmeaslesinpartnership125210 ай бұрын
@@SethHolmes Exactly. Leave well alone.
@2000SkyView5 жыл бұрын
good one!
@socialmeaslesinpartnership125210 ай бұрын
I hate to say it but.......thinking caps on. If the pins aren't of military uniformity, that's really no big deal at all - it's just OCD. What matters is that they seat firmly and hold the string. If a pin goes all the way in right up to the "shoulder" with the string in place, it's too small. Trimming them to get the pin "right down" is a mistake. Using a reamer is a much worse mistake. They should sit a little "proud", maybe a couple of millimetres but "how much" or "Are they all in line?" doesn't matter. If it sits a little proud, you know it's filling the tapered hole and is seated firmly - holding the string. If it ain't.....you don't know what it's doing. If it seats right to the shoulder, it's too small. To put a string on. Put the ball end at the top of the hole and push it down with the pin. Hold the pin in place, give the string a bit of a sharp tug to ensure the ball end is on the bridge reinforcing plate inside the guitar - not on the end of the pin or floating around inside the guitar. It seats the pin with enough tension and everything where it should be. You should then be able to forget about the bridge end, carry on with all the rest of it without any pins popping up, loud bangs or sudden loss of string tension when tuning to pitch - all that kind of thing. If not, the pins are probably not original, changed for cosmetic reasons, seeking a different sound, replacing just one that has broken, lost etc. Generally, it's better to seek different pins than shell out for a reamer - you can get after-market pins all over the place, there's a link here to do just that without messing your favourite guitar around. It's going to be very, very unusual that a guitar in your hands needs any attention to the pin holes.
@PhillipBunch3 жыл бұрын
Thank you!!!!
@BanjoBen3 жыл бұрын
you're welcome!
@kckong34 жыл бұрын
Mine has this problem - not seated all the way down as the others do. I noticed buzzing at the bridge pin/hole... is it because of the pin not seated fully??
@bubbly33824 жыл бұрын
Mine too... If you have fixed already. Then please let me know how to fix... My string is buzzing too.. Its really annoying...need Help
@kckong34 жыл бұрын
@@bubbly3382 i finally figured out why it was so bad on mine... the piece of wood on the other side of the bridge ( the bridge plate) was faulty. The factory had drilled the hole for one of the strings TWICE - it was not a clean hole, hence the string's ball end & pin were not fitted tight. I stuck my handphone inside the guitar to take a pic & that's how I found out. Maybe I was unlucky that this error excaped QC. Been promised a warranty replacement :)
@bubbly33824 жыл бұрын
@@kckong3 OH ! sorry to hear that.. And thanks for replying me.. My Bridge pin is still popping out but i found out that buzzing sound came from the other string on low E string on fourth fret ..I'm an absolute beginner I've been searching through the internet but still I couldn't find out how to fix..can you please help me out?
@socialmeaslesinpartnership125210 ай бұрын
@@bubbly3382 That isn't bridge pins. Neck relief (truss rod adjustment, first thing to check) or a high fret. Popping pins when re-stringing is usually "ahem" - not knowing how to change strings. Sometimes it can be the pins are too small but that's not usual on any factory-supplied.
@juansantana33805 жыл бұрын
Good video bro !!! Very well done 👍
@Flatpicknation5 жыл бұрын
I had like this with ALL pins. I used a nailfile to enlarge the hole abit. Was wat to snug fit .