No video
How To Fix floating Beads To Brick Or Block Wall Corner Beads New Window Float And Set Cement Render
Рет қаралды 6,870
Күн бұрынHow to set floating beads on the corner of a door or window works the same for both, Setting these beads with some bonding then will sand and cement render / float coat over the block wall and then a few days time can skim / plaster the wall finished showing you how I set them giving every tip and trick in the book for you to follow the step by step guid would be easy to follow for the home owner and diyer or even just so you know your options when it comes to how your corners can be finished and the steps taken to give you a good understanding on the job at hand, corner beads form a corner and allows plasterers to plaster both sides at once also reinforces it some to stop chipping from every day traffic. These corners can be done loads of ways as can be found and seen on our channel and i will share them below along with other great videos that can help you learn and improve.
This video shows you how to fit corner beads ready for plastering corners.
One of the big issues in plastering is making sure you have perfect angles and the best way to creating a corner is by fixing a bead to your wall.
Making an exterior corner on a concrete wall by hand forming a render corner with corner trowel and timber battens and rules very important part of plastering is the corners
• Forming Outside Corner...
How to Fit - Install Plaster Corner Beads aka Skimming Beads with plaster part3 • How to Fit - Install P...
How to bead window reveals • How to bead window rev...
ow To Fix floating Beads To Brick Or Block Wall Corner Beads
• How To Fix floating Be...
Rendering Window Reveals Sand Cement How To Fit the Battens Rules mix • Rendering Window Revea...
Float & Set Window Reveals Old School how to fit the batons rules loads advice & tips • Float & Set Window Rev...
rendering brick windowsill with sand and cement • rendering brick window...
How to Float & Set Window Wall Sand and Cement then Plaster Skimming full Tutorial
• How to Float & Set Win...
Float & Set Window Reveals Old School how to fit the batons rules loads advice & tips • Float & Set Window Rev...
Rendering Window Reveals Sand Cement How To Fit the Battens Rules mix • Rendering Window Revea...
How to Fit - Install Plaster Corner Beads aka Skimming Beads with plaster part3 • How to Fit - Install P...
HOW TO RENDER SAND AND CEMENT A WALL READY FOR PLASTER OR TILES ON AN OLD WALL • HOW TO RENDER A WALL R...
Sand & cement rendering block wall ready for skim coat plaster or tiles very detailed • Sand & cement Render W...
#floatingbeads #fixbeads #plastercorner
Spear and Jackson bucket trowel that is still going strong for me after many years = amzn.to/2pcpReS
Refina trowel pack and holder = amzn.to/33PbCvi
All amazon links are affiliated links will cost no extra to buy from but we might get a %
tools links direct
www.refina.co.uk/
Find us and like us here
/ macplasterin. .
Tweet us here
/ macplastering
/ macplasteringservices
our amazon store affiliate www.amazon.co....
@misterg1742 Ай бұрын
nice job guys , i struggled a little trying to understand your English guys but eventually i did :) !!
@macplastering Ай бұрын
@misterg1742 our accent would be hard to understand . So if you can you'll be flying .. thanks again and your welcome to our channel any time my friend
@patconnelify Жыл бұрын
Great channel very clear thanks, your skill set was always sorcery to me.
@macplastering Жыл бұрын
Thank you Pat mate :) He's a Wizard harry :):)
@barrygreenwood6251 Жыл бұрын
Old school roughing beads was all we did when I started out 1987 then dot a dab came along mid nineties Great video mate
@macplastering Жыл бұрын
I think float and set is a better way that dop n dab but for sure dot and dab is great for some jobs. i know a Chris greenwood plasterer who's pretty good at his craft Thanks for watching Barry mate
@seller1k Жыл бұрын
makes it look so easy
@macplastering Жыл бұрын
Easier with time
@noodles8203 Жыл бұрын
We do that sometimes with skim beads to create solid corners.
@macplastering Жыл бұрын
Yea bead them in I know a lot of guys like to stapple them on but sticking or planting as i call it is pretty full proof and not as slow as some think as you tend to stick the beads on with a few scoops left after doing 2 or 3 walls so no waste just like how i like it :)
@eaglegummybears7112 Жыл бұрын
Top man
@macplastering Жыл бұрын
Thank you brother :)
@pauledgar3274 Жыл бұрын
Good job mac
@macplastering Жыл бұрын
Thank you mate new video going live soon on channel thanks again for watching and commenting mate 👍
@ianturner8459 Жыл бұрын
Have you ever tried dabbing the reveals with plasterboard then floated and skim beaded around the opening before finishing.?
@macplastering Жыл бұрын
do that loads mate if you look at a few of the floating jobs i tend to dab my head board on but leave it out then work my to sides of there nice and margin :) then skim bead and skim away
@craigvarey9230 Жыл бұрын
What you're calling 'Margins' Mac, we call 'Reveals'. Is that what they're called round your way buddy? And where is that?👍
@macplastering Жыл бұрын
We call the reveals to mate The margins im talking of is the distance / measurement from the bead to the frame making sure it is all the same the whole way around keeping the margin right if you get me mate
@kamilaewska1663 Жыл бұрын
It would have helped fora novice like me to specify exactly what bonding agent is used for this, because I bought thistle bonding coat but don’t think it’s the same stuff. Please could someone advise? Thanks
@macplastering Жыл бұрын
It is the same mate
@kamilaewska1663 Жыл бұрын
That’s fab, thank you 🙏🏻
@macplastering Жыл бұрын
No problems my friend :) Thanks for watching @@kamilaewska1663
@johns9543 Жыл бұрын
what a great video you can tell you have a life time of experience, I have a wall that is damp, I'm using sika 1 sand & cement to waterproof it but the wall is miles out of plumb so I was gonna put the waterproofing on 10mm or so. then use bonding to build the wall out plumb & multi finish over the top, do you think I will have any issues with that ?
@macplastering Жыл бұрын
Hi john mate thank you for watching and commenting .... So if the wall is damp mate i would not go near it with bonding as it loves water and is like a sponge will take it in and hold it forever might be best sorting the damp issue at source / cause then use a few coats of sand and cement to build it out 10mm would be fine in 2 coats mate could almost get it in one but be easier if you filled out and scratched / keyed it again do a float coat then skim again
@johns9543 Жыл бұрын
@mac plastering morning Mac we have found after taking off a the ceiling & plasterboard walls we have a leaking roof (at home) so hopefully that will sort the damp in the wall out once it's sorted, the wall I will waterproof is ground level as there is no dpc, it's out about 20 or 30mm so I will just have to build it out in layers, hopefully the finish will be ok in sand & cement, as I'm a carpenter but multi finish & bonding are pretty easy to work with render is a little more tricky but if that's what needs doing I'll work it out, thanks mac I really appreciate it!
@macplastering Жыл бұрын
@@johns9543 I did find rendering harder to apply when learning to than gypsum as they are stickier :) You could add a little sbr in the mix it is great for water proofing helping it bound and might make it sticky for you but can also be a hard thing to spread as it tightens quicker and is stickier LOL you could scud coat then scratch coat 2 times if needed and a float coat and then skim sounds like loads but if not a big wall it will only be small mixes and we have videos covering all coats all mixes and methods that can be helpful mate and always here if you need to get a little help mate
@johns9543 Жыл бұрын
@@macplasteringthanks Mac,your a blinder. thats a great help , I just bought 1200mm speed skim metal & plastic & the pole so that should help, I will probably run 3 batton's down it to level off & do it in thin coats, its a kitchen wall so it has to be square for the work top, it's about 3.5 m x 2.5m so it shouldn't be too bad, I have rendered a meter or 2 before so I'll just do it section's of the battons, I like the scud coat idea I just watched 1 of your videos in it, did you say I could skim over the finish ? In mutli finish?
@macplastering Жыл бұрын
yes yes so if you get the final float coat on of sand and cement then devil float it / key it up and a day or so later you can 2 coat of multi finish on its same process as the finish we use saying that we use both multi and carlite here
@floodea 10 ай бұрын
Hey Mac, have your ever used plastic render beads for internal floating? Is galv better?
@macplastering 10 ай бұрын
Plastic would be more expensive and possibly a heavy coat think I have used them as they do arch bead that are flexible so still the same way finished wise
@johncarrigan9352 Жыл бұрын
If you were filling in a gap around a door and the angle bead was tighter than existing plaster as in there would be a slope from the existing drywall to the bead edge, what should one do?
@macplastering Жыл бұрын
Just seen your comment mate you could fill it out to a stick / rule 1st so it is sqare then apply the bead and finish I will drop a like to similar video but i think i finished it without a bead but same rules would apply :) video - kzfaq.info/get/bejne/mbdlrcqZl96rqWg.html
@JT-ce4bl Жыл бұрын
Did you record floating the wall as well ?
@macplastering Жыл бұрын
Hi mate have other videos on floating ready for skimming = last weeks video on a dead wall kzfaq.info/get/bejne/hMuDds-XtLS9n4U.html and another or a doorframe wall would be the same method as for beads as it is fro frames = kzfaq.info/get/bejne/Y7CYjM-nrqe3YWw.html
@macplastering Жыл бұрын
Let me know if them videos are helpful and for sure will be more videos on floating coming up
@robertchinn8728 Жыл бұрын
@@macplastering some of the corners I have to bead up are literally a couple of inches out from top to bottom. How do you normally approach these?
@macplastering Жыл бұрын
If real bad i would use a rule / Batton 1st then fill it out and set bead
@johncarrigan9352 Жыл бұрын
I had issues keeping the beads on if the wall was rough
@macplastering Жыл бұрын
yea can be a pain best to clean them down 1st a good scrapping or a little hammer to clean off any lumps should help
@johncarrigan9352 Жыл бұрын
I ended up nailing it :) I have a space now behind some of it because the gap wasn't cut straight....a few inches in places Can I put some acrylic filler in it.
@macplastering Жыл бұрын
Hard to know with out seeeing it but i am sure it could be filled one way or another to try and build up behind and make it strong ?
@Peanuthead1890 Жыл бұрын
Hi mac love the video's mate, can you fix a poorly placed bead aroumd a window reveal with a new bead on top or should i remove and start again, or can you improvise with a straight edge? Im not a plasterer im a diy merchant atal 🙈🙈
@macplastering Жыл бұрын
Some times you can re fit another on top but can cause a problem where the two beads meet a straight edge might be a better bet mate something like so = kzfaq.info/get/bejne/mbdlrcqZl96rqWg.html
@Peanuthead1890 Жыл бұрын
Thank you mate love your videos very informative and to the point keep up the good work, not to mention a very very good plasterer who can tell love your trade very much
@macplastering Жыл бұрын
@@Peanuthead1890 no problems mate glad to be helpful 👍 and always here if you wanna pop some questions mate
@Joe-jv5mm Жыл бұрын
Class Act, I've the same problem when looking for my 2ft level, you look everywhere and then find it behind my fat 🦻😂🤣😂🤣. KEEP UP THE GOOD WORK! 🖖
@macplastering Жыл бұрын
oh man thats me i need 2 or 3 of all tools as i miss place them all the time LOL thanks for watching :)
@Joe-jv5mm Жыл бұрын
If we added up all the time we spent looking for our tool's, we'd have 3 mortgages paid by now, have a dry 🪣 to hand when you put down a small ( level, Tape, snips, hammer, stapler/staples etc) pop it into 🪣, carry from room to room into van end of day, No more dancing the the plasters twirl 😂🤣😂🤣
@macplastering Жыл бұрын
LOL for sure man my issue with the bucket of tools i end no room in van a bucket for skimming a bucket for floating then dash job comes in LOL end up 5 buckets all a mess
mac plastering
Рет қаралды 36 М.
Дима Масленников
Рет қаралды 8 МЛН
Plastering For Beginners
Рет қаралды 188 М.
Plastering For Beginners
Рет қаралды 129 М.