You can do what I did but you can also buy anti vibration shims sea.banggood.com/custlink/v3KvqbLL3L

All ya need to do is loosen the centre bolt around 2mm ,then use a small spanner to tighten the long shaft clockwise towards the centre bolt and locked it. Just like I did to mine ,easy and safe. 😎

Nice!!! I fixed mine using bike inner tube, awesome do the job!!

Wow, great idea. At first, i thought cable tie would be very ugly, but you showed me, it is good. Using a two side tape could be an another way. But it can easily be dirty, probably.

Superbe vidéo, je viens de réalisé moi même cette pièce pour ma trottinettes Xiaomi M365 et c'est superbe, plus rien ne bouge ! Bon, c est un chiant à faire mais pour le résultat.. surprenant.. spécialement j'ai du en faire 2 et les attacher pareil que dans la vidéo, avec un seul j'avais encore du jeu, donc j'en ai fait un puis un deuxième en superposant les plastiques entre eux :) Le plastique venait d'un plastique de protection pour la cosmétique, plastique dure et transparent. Pour faire le calque une feuille normal suffit largement, puis découpe du papier, ne pas avoir peur de faire en haut du plastique assez large car après avoir mis le lock peu bloqué, donc donner un petit coup de ciseaux vers le bas du plastique ca devrait mieux rentrer, je vais mettre sur Facebook la forme idéale afin que ca rentre du premier en taille 1:1

really found this usefull loved the vid

well done... is really good idea buddy!

Good job dude 👍🏻

Nice video, nice solution. Great job.

I just spray the joint with WD-40. Works very well! No squeaky/cracking sound anymore.

thumbs up bro !

instead of 3d printing or cutting the "cartilage", I used Thermoplastic Beads... just heat it, place it into the joint and wait to cool down...

Starsky and Hutch music. Cool

If you let it be, Will it get damage over time or it is Just for the sound that it is annoying?

You can just tighten the bold by 1mm and it stops too! Much faster solution

I used glue gun instead, close it before the glue hardened you will get a perfect fit.

This is why 3D printing will be a normal part of life soon

Easier is just cutting 2 small pieces of thin rubber and putting them either side

If its making sound its good because it will go fast in speedbrakers

Hi there, are well done great idea thanks for showing this, I may just do this to my scooter when I get it thank you Oh and I hope what you did works okay let me know thank you.

Xiaomi are lazy or cheap.. This problems still persists even in the current models, you are better of getting another scooter with a different folding mechanism. This creaking will drive you mad, and no solution is permanent. I have been living with this creaking for over a year. At first, these kind of hacks work, but the creaking eventually comes back stronger than ever. For the last few months none of these hacks worked anymore. I finally bought an aftermarket replacement stem with folding different mechanism Monorim MPole 2.1 for 50 euros. Had a first ride with the new stem yesterday, and I felt so good. The stem felt much more stable, and the creaking is finally gone. I was about to trash the scooter before getting the replacement stem, the creaking was that bad.. Now it feels like the scooter is brand new again. If you are looking to buy a scooter, look for a model where the folding mechanism clamp is on the front, not on the back like Xiaomi models. I think all models where the clamp is on the same side as the hinge will eventually develop some type of noise.

i cant even get it to fold its so tight help

Better than 3d print

Why not use an old tyre tube rubber?

Or you can buy on Aliexpress just search for " M365 Rubber Pad Pole" -it's better for your scooter and hassle free. I just ordered one ;) Disclaimer: this comment isn't an ad hahha

Or u can try apply wd40 on it

Hi. Is it still safe to use the scooter even if you don't do something to fix the creaking sound?

I need more stopping power - Setting the KERS (RegEn) to STRONG - Will it increase my stopping power than compared to WEAK - my disc brake is not too efficient... Thanks.

Or just spray it with some silicone and you will hear nothing.

I have some strange CLICK noise, but it happens only once after braking or accelerating, here is the video if you could watch it: kzfaq.info/get/bejne/hc9naMqZqr-0eWQ.html I just removed everything in the hinge, cleaned and greased but it is still there. Does it ring any bells to you?

Yes, that annoying sound! :)

There is a easier fix. Using ductape/gorilla tape. See pictures. Dont mind the silicon. That didnt work. Ductape did. Just one layer of tape on each side not in the middle! And some tape araound the bar to hold it in place! See link imgur.com/a/THywlgW

Pfft, 99% of viewers will never even attempt to do this. This is so smart it's stupid 😂 Great job, just sayin'....

I put a plastic bag in it and cut the excess works a charm.

All that hard work when u could of just used WD40

I just used WD40 lol.

You don't Need fucking Art 🎨 Attack Guy's just use Oil WD40 or Grease

Pretty cool, but i dont have time for this.