How To Glaze Polymer Clay with UV Resin For Beginners ~ Tutorial

No video

How To Glaze Polymer Clay with UV Resin For Beginners ~ Tutorial

Рет қаралды 3,800

Күн бұрын

Hi, everyone! :) (For tools used, click 'show more')
In this UV resin/polymer clay tutorial for beginners, I share lots of tips, tricks and techniques on how to perfectly glaze charms/creations/jewelry/earrings every time! 💕☺️🎨
- Baking Polymer Clay Tutorial: • How To Bake Polymer Cl...
Chapters:
- Intro: 0:00
- What is UV resin: 0:22
- What brands are there, which is best: 1:12
- When to use UV resin: 3:23
- When NOT to use UV resin: 4:24
- Tools needed: 5:32
- Workspace set up: 9:20
- Storage: 10:23
- Curing times: 10:57
- Preparing charms for glazing: 12:03
- How to use and glaze with UV resin: 13:18
- Glazing pieces in stages: 16:06
- Curing pieces in one session: 16:49
- How to tell UV resin is cured: 17:12
- Doming flat objects: 17:59
- Securing earring posts: 19:01
- Troubles with resin / solutions:
• Yellowing / discolouring: 21:22
• Stickiness / Incomplete curing: 22:28
• Bubbles: 23:08
• Repelling / pulling away: 23:57
- How to clean up UV resin: 25:15
Tools used:
Main UV resin tools -
- UV LED resin (brand: Handcrafter)
- Paint brush
- Silicone cupcake liner
- UV LED lamps / natural sunlight
PPE/Safety Gear -
- 3M half face mask
- VOC P95 filters
- Safety goggles
- Nitrile gloves
- Arm covers
- Hair tie
- Old clothes
- Apron
Preparation tools -
- Baking paper
- Baked polymer clay creation
- Loctite Gel Control super glue
- Needle point applicator bottle
Hanging tools -
- Paperclip(s)
- Chopstick(s)
- Sticky / Sello tape
- Thick cardboard
- Kitchen foil
- Mini pot plant
- Canister jar
- Wire rack
UV lamps -
- UV bulb lamp (36 watts)
- UV LED lamp (48 watts)
- Mini UV LED lamp (6 watts)
Workspace set up:
- Glass work surface
- Isopropyl alcohol wipes
- Trash can
- Trash liner
Rest of tools -
- Blu-Tack / adhesive poster putty
- Aluminium metal lid
- Silicone pot holder
- Toothpicks
- Earring post
- Sculpey Bake and Bond / Oven Bake Clay Adhesive
- Fresh polymer clay
- Oven- Sandpaper
- Water
- Kitchen stove lighter
- Water based polyurethane glaze, matte finish
- Nail polish remover
Music:
Ukulele - Bensound (bensound.com)
Music by Bensound.com
License code: D3FA8MST6NYETMUB
✨ Check Out These Polymer Clay Basics:
• Shading Polymer Clay: • How To Shade with Chal...
• DIY Popsicle Stick Depth Guides: • How To Make Popsicle S...
• Kawaii Faces + Tiny Mouths: • How To Make Kawaii Fac...
• Polymer Clay Sauces: • How To Make Sauces wit...
✨ Easy Charms To Start With:
• Kawaii Stars: • Mini Kawaii Stars ~ Po...
• Kawaii Tetris Blocks: • Kawaii Tetris Blocks ~...
• Easy Macaron: • Easy Mini Macarons ~ P...
Social Links - Follow Me:
Instagram: cloudfetti
Facebook: cloudfetti
#polymerclay #polymerclayminiatures #Polymerclay #Polymerclaytutorial #PolymerclayDIY #Polymerclayart #Polymerclayminiaturesdiy #Polymerclayminiatures #Polymerclaycharm #Polymerclaycharms #uvresin

Пікірлер: 27

@LearningToLive336 17 күн бұрын

This is the most comprehensive video I have ever seen about UV resin, and this has changed a ton of how I will do things from now on!! Thank you SO much!!

@Cloudfetti 17 күн бұрын

Wow, thank you and you’re welcome! That’s great to hear! 💕☺️

@leannhill4216 Күн бұрын

You're turorial was FANTASTIC for me, a beginner! Thank you for your precise and thorough teaching 🎉

@Cloudfetti Күн бұрын

Yaaaaay, I'm so glad the video was super helpful to you! That just makes my day! ☺💕

@cw9821 4 ай бұрын

Great tutorial, lots of helpful tips! Thank you for sharing. ❤❤❤

@Cloudfetti 4 ай бұрын

You are so welcome! Glad it was helpful to you! 💕💕💕

@CoolRiceBunnies 4 ай бұрын

Extremelyyy helpful and educational video. Thank you for sharing!!

@Cloudfetti 4 ай бұрын

Thank you so much and you’re welcome! I’m so happy you found it helpful and educational! ☺️💕

@user-cq8ti5pe7g 4 ай бұрын

Omg I love this tutorial. Thank you so so much❤

@Cloudfetti 4 ай бұрын

You're welcome and thank you sooo much! I'm so happy you like it! 💕🎨 (Also, I just had to post another community post thing, I uploaded the wrong photo of the close up cat charm and it wouldn't let me edit it 😂 so if you were looking for your comment, and it's gone, that's why! 💕)

@user-cq8ti5pe7g 4 ай бұрын

@@Cloudfetti 😑 ok then, the first 'like' and 'comment' is going to be me 🤣

@Amberthecat334 Ай бұрын

AAAAHHH this literally answered every question I've ever had about this!!! This is exactly what i needed! THANK YOU SO MUCH!!!

@Cloudfetti Ай бұрын

Oh, yay! You're very welcome, I'm soooo happy it was helpful to you! ☺💕

@sheidatt9390 29 күн бұрын

Thank you so much for this video! It resolved all of my questions. I have a question tho. I have the same Suny mini UV lamp and I used it repeatedly on a small piece of airdry clay, but it doesn't cure. It cures like 90% but it still has that 10% of tackiness. It's actually very frustrating, do you have any idea of what I'm doing wrong? I also used a very thin layer. The piece is also vey small so I expected it to cure quickly. Maybe it doesn't work on air dry clay?

@Cloudfetti 29 күн бұрын

You’re very welcome! I’m so glad it answered your questions! I personally haven’t tried it on air dry clay but I think it would be fine to use on it. The only thing I can think of, if it’s not working on air dry clay, is if the clay hasn’t fully dried yet? It could look dry from the outside but still have a bit of moisture inside it. I’m not really sure, as I don’t use it that often, but you could try it again on a test piece that’s dried for a few days, then glaze it and cure it with the light to see if that works. If it doesn’t, I would place the piece outside in the sun for a few hours on a hot day so that the tacky parts of the UV resin can cure all the way through. I find that the lamps are great, but it still doesn’t beat natural sunlight, imo. I hope that helps! 💕☺️

@sheidatt9390 29 күн бұрын

@@Cloudfetti Thank you so much for the thorough explanation. You're really sweet💕

@Cloudfetti 29 күн бұрын

@@sheidatt9390 Aw, thank you and you're welcome, I hope it all works out! 💕

@tejebonito 4 ай бұрын

I also have the flowery pot and its suuuper yellow, takes ages to cure...i found SAANNAA much much better, super clear and cures in the 120watt UV/LED lamp Tempered Top Coat or a Rubber Top Coat without the sticky layer is better and a cheap option. I got recentley UR Sugar Reinforcement gel and once you removed the sticky layer leaves a suuuper lovely shine.

@Cloudfetti 4 ай бұрын

Oooh! Yeah, not the biggest fan of the Qiao Qiao brand, but I’ve heard great things about the SAANNAA one. Thanks for the info about the top coats! ☺️💕

@murphchris5670 18 күн бұрын

Hi, I made badges with polyurethane fast cure resin and there were bubbles and holes on the bottom. I was wondering can I fix it with UV resin? Cheers

@Cloudfetti 18 күн бұрын

I personally haven't used that kind of resin, so I'm not sure, but you could put UV resin on a small spot where it won't be so obvious, just to try it out. Sorry I couldn't give a definitive answer, but I hope it all works out! ☺️💕

@aliendrummergurrrl4849 4 ай бұрын

Hi, thanks for this tutorial! I'm just wondering why my polymer clay keeps darkening a bit in the oven, is that just a thing? I use Fimo clay, by the way.

@Cloudfetti 4 ай бұрын

Hi, you’re welcome! I hope this video is helpful to you! Polymer clay does tend to darken in the oven if it’s not covered with something to protect it from the top heating elements of the oven. I found it’s usually caused by the heat and longer baking times. You can prevent it by using a foil ‘tent’ over the top, or even better, a foil bbq tray, which is more sturdy. I have a video on my channel called “how to bake polymer clay for beginners”, and at the 20:02 mark, it has a chapter called ‘browning/darkening of polymer clay’, which has a visual of the bbq tray if you need it! Make sure you’re also using a separate oven thermometer to check the proper internal temperature of your oven, because oven dials are often incorrect and can heat hotter than what you actually set it to. I hope it helps! 💕☺️

@aliendrummergurrrl4849 4 ай бұрын

Thank you so much for getting back!! It was very helpful, thanks! 😊

@Cloudfetti 4 ай бұрын

You’re welcome! 💕☺️

@wasabi8197 2 ай бұрын

Can you please tell me why my uv resin is uneven on my charms having trouble with evening them on my charms that are not flat 😭😭

@Cloudfetti 2 ай бұрын

It could be that you are putting too much on one side, and not enough on the other, or, that if it's not a flat charm, it could be the resin dropping/flowing to the lower side with gravity. You could try to brush on a thin layer all over the charm, cure it and then continue to build the layers, which is the method I like to use. I hope that helps! ☺️💕