How To Install a 240 Volt Outlet | Electric Car Charging

Рет қаралды 2,571,806

Күн бұрын

Complete List Of All My Favorite Tools - www.amazon.com/shop/everydayh...
Safety First! Make sure you have the knowledge and experience needed prior to taking on this project. This video will cover all the steps needed to install a 240 Volt 50 Amp (NEMA 14-50) Outlet. This project is becoming more common for homeowners as the adoption of electric cars is increasing rapidly.
Joel's KZfaq Channel (Electric Pro Academy)
/ @electricproacademy
Parts List
240 V NEMA 14-50 Outlet: amzn.to/3AJMKFc
4" Square Electrical Box: amzn.to/2XdAeQu
4" Square Box Mud Ring (1/2"): amzn.to/3lHQlPF
NEMA 14-50 Faceplate: amzn.to/3vexHlI
Drywall Anchors: amzn.to/3BQjlKY
3/4" LB Conduit Body: amzn.to/3lKvJXf
3/4" EMT 90-degree Elbow: amzn.to/3j2YaOq
3/4" EMT Connectors: amzn.to/3BIYDw9
3/4" EMT Couplings: amzn.to/3mUI0aN
3/4" EMT Mini Conduit Hangers: amzn.to/30sOzdc
3/4" EMT 1 Hole Strap: amzn.to/3p44IzT
50 Amp Square D Breaker (Type QO): amzn.to/3BJDxy3
6/3 Romex Wire: amzn.to/3oYSVD4
Chapters
0:00 Intro
0:45 Project Overview
5:58 Parts Overview
10:23 Fishing New Wire Through A Wall Cavity
14:26 Cutting Hole In Drywall For Conduit Body
16:37 Installing Conduit Run
25:44 Pulling Wire Through Conduit
36:46 Installing 220V Outlet In Electrical Box
42:14 Final Wire Connections At Electrical Panel
46:57 Final Test and Validation Of The System
Tools Every Weekend Warrior Needs
Makita Corless Drill Combo Kit: amzn.to/2Jsw78j
Dewalt Drill Bit Set: amzn.to/2w0xAA4
Dewalt Screwdriver Bit Set: amzn.to/2UqTvK9
Craftsman Screwdriver Set: amzn.to/3bAsNEG
Eklind Allen Wrench Set: amzn.to/2wKDu8M
Pliers (4-Piece Set): amzn.to/2JlYUM7
Milwaukee Fastback Utility Knife: amzn.to/2WFZOgt
Stanley Tape Measure: amzn.to/2WPzr5K
Studbuddy Stud Finder: amzn.to/38MdzfV
Johnson Torpedo Level: amzn.to/3dzx5Ot
Stanley Hammer: amzn.to/39tudPL
Buck Bros Wood Chisel Set: amzn.to/2QTebYO
Klein Voltage Tester: amzn.to/3yYjzh8
Klein Outlet Tester: amzn.to/39GyO33
Milwaukee Wire Strippers: amzn.to/2Z1jH2J
Little Giant Ladder: amzn.to/2UrFmfG
DISCLAIMER: This video and description contain affiliate links, which means that if you click on one of the product links, I’ll receive a small commission.

Пікірлер: 3 200

@richardkaufman1643 2 жыл бұрын

Enjoyed this well presented video. As a master electrician in Michigan for 40 years I do have a couple of comments. First I would have used a 4 square box on the wall above panel, you would have eliminated a lot of stress. Two, on the outlet I think the sharp corners of the flush use plate may be just waiting for someone to cut themselves, a raised cover would have been the correct one. Also when working with a metal fish tape in a panel is always dangerous. A no conducive fish rod would have been my first choice, if not available I would have stuffed a cardboard guard inside the panel. Safety first !

@noahflores5515 2 жыл бұрын

thanks for the tips.

@normankujawski543 2 жыл бұрын

As a previous electrician I agree with you.

@sntcz8 2 жыл бұрын

This is great information, thank you 🙏

@anthony4530 2 жыл бұрын

My father was a master electrician here in Michigan as well (IBEW 692.) There were a few tense moments in this video until I remembered that if this guy would have made contact he probably wouldn’t have been “available” to finish this project 😁

@animalmother111 2 жыл бұрын

Still would have covered the breakers with cardboard!

@brandonknight7240 2 жыл бұрын

The way these videos are coming leads me to believe you are working as an apprentice electrician and posting what you learned that day or week

@lciummo1 12 күн бұрын

DIY audience.

@ronmaynard7424 Жыл бұрын

Guys and gals listen to this man when he says "buy an industrial rated outlet" buy a hubbel not the cheap 12 dollar one from.big box!!! Those are good for dryers and such not a constant 50 amp draw for hours! I know the hubbel is 50 bucks more but I've seen my welders melt the cheap ones and your EV is drawing more then my welders and for longer. Don't die in your sleep over 50 bucks. Excellent video

@UGotTheFunk 28 күн бұрын

This should really be pinned. I'm surprised they installed an Amazon speical crap-o 5000. Hubble or bust.

@Store4421 28 күн бұрын

I was able to install about 90 feet of 6/3 wire using your video as a reference guide and saved myself thousands of dollars. I just wanted to say thank you for the clear, and easy to understand video. Anyone thinking about doing this project can absolutely do it, just don't cut corners. Make sure you get a commercial grade Outlet like he said in the beginning of the video, and based on what iv read it sounds like a cheap torque screwdriver will be helpful to make sure those terminals don't ever come lose and cause problems in the future.

@user-qn6yt3zx3w 2 жыл бұрын

Especially for DIY’ers - if the appliance end is already completed and you are wiring into panel, ALWAYS check for continuity (short) between the cables before you land them in the panel. Once landed, it’s not easy to check. If you get continuity between any pair of wires, there is a short and you must not land any wires.

@nilpo Жыл бұрын

Good advice.

@TravelWithMEnow Жыл бұрын

Thank you so much for this great video. I was able to install my 14-50 NEMA receptacle very easy thanks to your detailed instructions and materials guide. Again thank you so much for sharing your knowledge with the common “Do it yourselfer!” 😊

@stkyrce 9 ай бұрын

I've already install a 240 and this lines up with what I've done. Excellent video. Thank you for taking the time to do it.

@Jetbill007 Жыл бұрын

Amazing attention to detail and positive attitude here. True mark of a great leader.

@tubeDude48 Жыл бұрын

I was a journeyman in the '60's, but now I see so many changes...so this was very informative! SUBSCRIBED!

@thedevilinthecircuit1414 Жыл бұрын

That metal cover plate on the receptacle has sharp corners that will slice open a hand. Get a smooth galvanized cover plate that follows the shape of the box. Way more safe. Great vid!

@edchenal821 Жыл бұрын

Thanks for being candid. It makes everyone safer including you.

@orangenblk Жыл бұрын

The most professional teaching video I have watched. Well thought out and executed. Great, upbeat presentation. Fabulous job.

@EverydayHomeRepairs Жыл бұрын

There is more where that came from! Joel has his own channel at kzfaq.info and puts out a TON of great stuff.

@ethelryan257 2 жыл бұрын

There are old electricians and their are bold electricians. Not too many old and bold electricians. I don't work on live distribution boxes if I can possibly avoid it. Being a woman, I don't have to compensate for 'shortcomings' by taking unnecessary risks. Great video, cute sparky. I believe 3/4" conduit is too small for current code on #6, I'd have gone up to 1" and lube is your friend.

@bobcolella8539 21 күн бұрын

I’m trying to figure out why he ran 6-3 through conduit - couldn’t he have saved a lot of time and money by running individual THHN/THWN wires? Isn’t the shielding of the 6-3 overkill? And as you mentioned - doesn’t he want to use 1 inch conduit based on the fill space of the 6-3? What am I missing?

@YuDuo-dc8md 3 күн бұрын

Yea fiberglass fish tape for me I used 32 mm 1 and 1/4 in 12th of a kings foot measurements and put in a draw wire for possible additional wiring without ripping it all out or running alongside a few dollars up front 100s saved later.

@albertstrong5516 7 ай бұрын

Ground should be attached to the metal box and receptacle. That's a pro tip

@scottdhorn 13 күн бұрын

Didn't see him torque the wires either. Maybe he did, just didn't show it.

@lciummo1 12 күн бұрын

Isn't the box bonded to the receptacle ground via screws.

@pld8993 10 күн бұрын

@@lciummo1 Box must be grounded independently of the receptacle.

@papaown 3 ай бұрын

You are an amazing teacher and very good at speaking about wiring to laymen, like myself. There are plenty of installers out there, less true professionals, and even less that know how to teach. Thank you for the video. I'll probably never do this install by myself for my Model Y, but it's cool to be more informed before hiring someone to do it for me.

@johnspruit7296 Жыл бұрын

This guy is an EXCELENT teacher. Thanks .

@EverydayHomeRepairs Жыл бұрын

He is and Joel also has his own channel where he goes over a ton of great Electrical info www.youtube.com/@ElectricProAcademy

@deadsmooth419 2 жыл бұрын

You are great at explaining what should be explained in depth and I appreciate that you don't just assume that everybody should already know the basics...im a handy man and take pride in my work but learned a whole lot of things in this video that I will use going forward...thanks

@guyfioreii8901 Жыл бұрын

Ive never watched a more informative, professional, extremely well explained youtube channel. Thank you for all your work!

@markkempton4579 Жыл бұрын

This was a fun video, and I actually found it more enjoyable than most of Joel's videos. It seemed more straightforward with less joking around. It also explained a lot more that I think is sometimes skipped over with his usual videos, maybe because this was intended for DIYers.

@drlovedrake 3 ай бұрын

Thank you for this video! I followed it step by step, and made use of pretty much every tip and trick mentioned. And now I am charging my new electric car in my garage. This video provided exactly the level of detail I needed to do the install.

@troyvoorhees 2 жыл бұрын

This was a fantastic video to teach a relative newbie like me how to install a 240V NEMA 15-50 plug to charge my brand new EV. This was instrumental in making me feel like it was a job I could tackle. Everything turned out great - thank you!

@timwilson3150 2 жыл бұрын

It’s NEMA 14-50R outlet.

@RetiredSignDude Жыл бұрын

Make sure you shut the power off

@sammelton3569 Жыл бұрын

Great video! I always use non-conductive fish tape, especially when working near live circuits. Many job sites require it.

@joelwalsman773 Жыл бұрын

That's a great idea! I'll be purchasing one

@evetsdn Жыл бұрын

Fantastic tutorial ! I learned a lot, took many many notes. Stopped , replayed , restarted so many times I lost count . I didn't want to miss anything. I spent over 2 hours watching the 48 min. video , couldn't get enough. Thank you very much. I will be assisting my brother who is an electrician in installing an electric car charging station in my house and I didn't want to look like a dope. And thanks for NOT having any loud distracting music in the background as so many other You Tubers do.

@kinglc4789 11 ай бұрын

the only only a see as t au😅sadatsssssssssSsssssssSŚddyYssDddddsdDddddDsddddddddddddzdddwz😊😊ttttxYttftttttttfftdtyyytrrrsdddddssssssssssssssssssssssssdddddssssdsddsduzddddttutufdddfffffffffffffgyta😅

@user-mx4wq8to8o 7 ай бұрын

Many thanks. Explaining things to us DIYers in clear, concise language we can understand is greatly appreciated.

@donwat91 2 жыл бұрын

I've only done this once before . I put in a outlet in for my RV at a friend's house. 4 pole 240 volts. Now I'm getting ready to run another one where I park my RV at home. And I've been looking for a video to confirm the panel connections. You do a great job explaining the whole process, thank you. I enjoyed it.

@EverydayHomeRepairs 2 жыл бұрын

Best of luck on the project. I need an RV 😁

@dontbanmebrodontbanme5403 Жыл бұрын

Great video! I learned something new with the freakishly long needle nose plier tool. I'm a DIYer, but in the past, I've used coat hangers and all types of crap to get that wire out. Good to know that tool exists. If it's less than $50, I'll buy it. Personally, I wouldn't use drywall anchors to hold such a heavy plug. Then again, I'm one of those people who overdoes things. I would have reinforced the outlet with wood supports. So I would have cut out the sheetrock, added wood studs, and added the sheetrock back and re-taped it. Lastly, and most importantly, the outlet you choose if of CRITICAL IMPORTANCE!!! While you can go to any big box store and pick up a $9 NEMA 50 amp plug (the kind used for electric dryers) DO NOT USE THOSE! Those are not designed specifically to have current running through them for hours and hours and hours and there have been many stories of those melting and worse, starting fires. Get the industrial kind, like Hubbell. As of me writing this, they're $80, so they're not cheap. But if you're going to spend $50K (or more) on an EV, you're already saving money by doing the job yourself. Don't have your house burn down over a few bucks.

@blackrifle6736 Жыл бұрын

*Appears that Joel is installing a Hubbell 9450A, 50A, NEMA 14-50R receptacle. This is an industrial grade piece as FedSpec grade is expensive overkill. This is better than good for extended duty-cycle home use. $90 on Amazon. Do it once, do it right and be secure in the knowledge you did so. Your clue is B00IPBMUKY. Cheers!*

@DeeJay_IMB Жыл бұрын

Good video. I just started working on some DIY electrical work at home. I recently came across your channel and Joel's. They're very easy to watch, and very detailed.

@PopsGG Жыл бұрын

I love when videos are so detailed and well done. It gives all the steps and details you need to realize you need to hire a professional.

@DanT10 Жыл бұрын

I had a pro install my charger. I cried a little when I had to pay. But it was installed and it is right and years later never a problem.

@nilpo Жыл бұрын

This was detailed, but there were still some important points left out and this won't pass inspection.

@AJ-ri5ee 3 ай бұрын

@@nilpowhat specifically wouldn't pass inspection? And where(country/state)?

@nilpo 3 ай бұрын

@@AJ-ri5ee North America. Specifically in the US it won't pass NFPA 70. Pretty sure it doesn't pass in Canada either.

@AJ-ri5ee 3 ай бұрын

@@nilpoOk, but what part?

@tipstricksreviews4481 2 жыл бұрын

It was great video. There are some recommendations: - Using glows and safety glasses are always better, especially when you work in a live panel. As seen in viodeo, even you as a professional can cut your hand. I understand you are a professional but similarly you could get shock. -You forgot to use plastic conduit bushings at the termination locations. -it is better to mark the high of box and cut your conduit accordingly. It can give a better result for box the high, and reduce risk of miscalculations. -Better to kill the power before start, since your fish teyp is not the plastic one, you could make a short-circuit. Thank you for the video and fishing tips.

@Pepe-dq2ib Жыл бұрын

I though plastic bushings are only required in FMC/AC/BX and not EMT/RMC

@rodneyparker9912 2 жыл бұрын

Great video. My 2 cents as a master electrician..... 4 square above panel instead of LL/LR/LL, fiberglass fish rod for wall fish, raised industrial cover for receptacle, and metallic outlet box must be bonded as the conduit run is not continuous to panel.

@keithharrington8715 Жыл бұрын

This job would look different if I did it too. However, did he violate code anywhere? I question if the box is grounded iaw the nec. Just found this one.....but 406.11 (recepticles) connecting the ground terminal to the box.....250.146.(A). Roecepticle ground term to box, surface mounted., the yoke to box connection shall provide the effective ground path. So the box is grounded as per 314.4? The only possible violation I can see is 625.54, which requires a gfci breaker for car charging (ELECTRIC VEHICLE SERVICE EQUIPMENT) recepticles. I only deem it possible because of 90.4 and not enough information from ahj. Please not 625.54 the gfci requirement ...car charging was not changed in 2020 so maybe for 2017 or earlier. Now, I consider myself an "A-" guy.....good but not perfect. So if I missed a concern please let me know. And if I have a reference wrong, yeah, give that written smack down.

@rodneyparker9912 Жыл бұрын

@@keithharrington8715 I think he did a good job, but to answer your question yes. The 4x4 outlet box utilized for the receceptacle would be required to be bonded to be code compliant. A ground stinger should have been installed into the 4x4 box, which would bond the box, attached metallic conduit, fittings, and metallic receptacle cover to prevent them from becoming energized.

@rodneyparker9912 Жыл бұрын

@@keithharrington8715(IMHO) The articles you are referring to allow the receptacle to be grounded via its yoke in direct connection to the box. Not vice versa. Not good practice either way and would be highly frowned upon by ahj if you tried to use this shortcut.

@keithharrington8715 Жыл бұрын

@@rodneyparker9912 sir, I would have attached the egc with a wire to the box and recepticle (pigtailed it). However, 250.146 says you can skip the bonding jumper if you do 250.146 A, B, C, or D. It looks like here he followed (A).

@keithharrington8715 Жыл бұрын

@@rodneyparker9912 thanks Rodney. Looks like you are right. Did some better reading and The yoke can ground the recepticle to the box connected to the egc..

@mgvarghese Жыл бұрын

Excellent gentle man thanks a million i was searching for a video like this. I am going to watch minimum 5 times to grasp a step-by-step approach

@jmlastname4412 Жыл бұрын

Some good information...I guess. I would never pull NM through conduit. Code or no code. To keep it clean above the panel I would use a 411 box. It is ok to make joints with wires. I know some will cry that it is a potential trouble spot but not if you do it properly. NM in wall then THHN in the conduit. The condulet at the top of the wall is more work than is necessary. Well made video! I like the effort the young man made to explain things to DIYers.

@VanderJam Жыл бұрын

From one pro to another.... Great video. Popped up in my KZfaq auto play while I was doing chores. Couldn't turn it off. Well done. You really should be teaching in a local trade school if you're not already doing that. Outstanding communication skills.

@lancelongrod9333 8 ай бұрын

Then why his wiring look like that.

@danielball4272 8 ай бұрын

No he should not, and you are not an electrician, or just the use of romex in EMT, should have had you pulling your hair out!

@oleanderson3693 2 жыл бұрын

Without commenting on the accuracy of everything said, this guy is an amazing KZfaq instructor. No obvious cuts for take after take. Lots of hints. Great communicator. Not his first rodeo. My biggest issues? Don't use drywall anchors for such a big box, it wiggled. Locate stud first or use toggles. Violated his own safety rule using steel pull tape on a live panel.

@joelwalsman773 2 жыл бұрын

Yeah, you're right Ole. Time to update the old tools.

@joelwalsman773 2 жыл бұрын

It can be so hard to compromise the flexibility and durability of the metal tapes for the fiberglass, though.

@SCGATOR2001 7 ай бұрын

I"m an EE who worked as an electricians helper several summer both before and during college. You can't know too much and it's great to watch a professional again as solar projects are coming up just around the corner.

@obfuscated3090 9 ай бұрын

These outlets are also terrific for powering large single phase air compressors and welders, and rotary phase converters to run things like used three phase industrial air compressors, welders etc depending on size. DIYers with patience can wallow in quality used industrial equipment for same or less money than consumer crap but having that large single phase outlet (or more than one since parts are cheap and you're in there anyway!) is key. I even added them to my rented house (with landlord permission, he was also my best friend) and took them when I moved. Look into the many products including cords, splitters and other hardware used to power RVs from these outlets. I promise it will be useful info if you DIY. Related note re: "cool stuff powered by outlets": I put my horizontal tank compressors and my welders on dollies I fabbed to use scaffolding casters (which just slide into a tube and are magnificent, get the round shank style) for easy handling. If you rent and put everything heavy on wheels the rest of your life gets impressively easier. You eventually need to move most of your stuff so if you make that low effort in the beginning you never sweat again.

@egolono10 2 жыл бұрын

Excellent video, I didn't imagine myself watching this in one sitting but Joel's calm teaching style and work flow is mesmerizing to watch. Thanks so much for the collaboration, Scott and Joel! You guys both put out quality, well-articulated content. Also subscribed to Joel!

@j.a.r.family2576 Жыл бұрын

Metal in a hot panel..... NO!!! WORST MISTAKE

@humbertohidalgo1748 Жыл бұрын

He has leadership tone and patience something I really like to embrace with my crew . Win win .

@twoweeledsoto6072 Жыл бұрын

I also felt this video was very informative. I pretty much ignore the "let me see what I can criticize" people. 😅 If they posted a video, there's be others criticizing their procedures, have not doubt.

@truthdefenders- 11 ай бұрын

“mesmerizing”? I was waiting for the spark and lights out when he was letting that fish tape just flip around in the panel. 😬

@vinceandrews9187 7 ай бұрын

This guy is a hack electrician, die cast coupling, steel connector, mixing type of connectors, WRONG next it’s a 3/8” offset not 1/2” offset. If this guy new his sheet he wouldn’t run 6/3 romex through an LB, ROMEX IN A CONDUIT IS ALSO WRONG, DIY just have the guy at HD cut individual wire to your length, 40’ feet of conduit eguals 3- 46’ of #6 and 46’ of #10 green, individual wire is more cost effective than romex

@micheleploeser7720 Ай бұрын

An absolutely perfect video on AC electrical systems and how to make it safe and all that being an old shop teacher I have to tell you put on safety glasses before you start any work thank you very much for a good video

@Grandma_angle 9 ай бұрын

This guy wire installation is so amazing! Well done & clean!

@DavidRojas-zb8wo 3 ай бұрын

Hi, I used your video to install a NEMA outlet for my EV. It was super helpful and I can’t believe I was able to do it myself. Thank you for sharing your knowledge and expertise!

@EverydayHomeRepairs 3 ай бұрын

You bet!

@hpe1087 Жыл бұрын

Very good video & illustration of this electric installation. The pros were able to identify several areas that need to be considered with this electric project to meet a safe NEC installation. Also, when working in or around energized equipment, OSHA, mandates PPE equipment to be worn for added safety. Always best to de-energize equipment when working in or around electric equipment. Otherwise, a very educational video!

@joelwalsman773 Жыл бұрын

You're right! Safety hasn't been my strong suite (neither has spelling 🙂)

@BilboBaggins-wf8sk Жыл бұрын

This is fantastic. Its detailed and to the point for people like me that are not handy this is great. Thank you very much for this video.

@Dean-Sala Жыл бұрын

Thanks to you, I am now very confident that I can install EV receptacles for my clients. This will help my handyman business grow even further!

@SB-kk3wi Жыл бұрын

Too many things to comment on. Not what I would consider a pro job. Retired master electrician. Never worked in a place that would allow a three or four inch chase nipple in the top of the panel and allow all the circuits to run through it. Amazing. Also, if you're going to work on a live panel (And I recommend a DIYer never do such a thing), take a piece of cardboard and tape it over the panel on three sides allowing just enough room to push the top of the cardboard into the panel so that you can insert your fish tape through the top knockout. This should keep you from contacting any live circuits when that fish tape accidentally flops around. Nowadays, they actually have fiberglass fish tapes which would be a lot safer for this job. I also spent 20 years as a paramedic and took countless DIYers to the ER for attempting jobs like this on live panels. JMO.

@pld8993 Жыл бұрын

Not a pro job. Just because it works that doesn't mean it's done correctly, lots of violations.

@lock-man-do7842 Жыл бұрын

Awesome video! Thank-you so much for sharing your skills in Electrical installs. I picked up on several of your tips (at least 10) that you can't find in any books. I've pulled wire thru conduit and made the work much harder than necessary - with your tips, I'm actually looking forward to the next adventure with cable and conduit. Again, Thanks

@jerrybell3600 Жыл бұрын

Amaà of of

@guyshipely9993 Жыл бұрын

I particular liked the bending of the wire to get into the breaker.....

@srbeeffarm8586 Жыл бұрын

Excellent video, Thank you! I do not have a main panel in the garage however my meter is just outside the garage. I am going to install a single DO 50 amp breaker in a an A/C type box on the garage inside wall near the outside meter, use your information to install the inside plug receptacle then have an electrician make the short connection through the garage wall and to the meter stand. Again a very well done video!

@johnstobbscpa8081 Жыл бұрын

Thanks for the great info. Just bought a Tesla 3 which is months from being delivered. Electrical is something I leave to the trade but this was helpful in understanding to what I need to have done.

@rolandos64 2 жыл бұрын

hands down one of the best tutorials on KZfaq. It was a random video I selected. I am not making an installation. I simply enjoy learning visually. Your teaching is superb!

@johnmilner6419 3 ай бұрын

Attaching the power wires to the unattached breaker, and then snapping the breaker into the box, is a slightly easier way to proceed. Anyway thanks for doing it LIVE! (Ha ha ha)🙂

@flolou8496 5 ай бұрын

Damn it, you guys need to do this all over again, for those homeowners who don't have panels in enclosed garages, but have them often on the side of the house a good 35 feet to 50 feet away from the driveway !!!

@mrjon7502 3 ай бұрын

I agree there isn't any videos out there running 6 gage from the side of the house panel either up from the roof through the sky lol back down to the garage or underground from the side to a garage that is 50 feet away.Most vids are like I bought my 2 feet of Romex at $2 lol you an I are like in the $400 dollar range. anyways The dude that made this video is awesome I love it and it made sense for us DIYers thank you brother, keep it up.

@karlInSanDiego Жыл бұрын

Appreciate you showing your trade skills to us all. Really helpful!

@DriverDude100 Жыл бұрын

Thanks for the video. Your friend is an enthusiastic electrician and a great teacher. Agree with commenters that some things could have been done better. For instance, much prefer THHN wire in conduit and would like to see a conduit system go from panel to box. Would consider the installed tubing in this case to be more of a protective sleeve rather than a true conduit system. Also not a fan of the faceplate arrangement on the wiring device. Regardless, enjoyed the video. Always glad to see other pros work. Keep up the great work!

@_P0tat07_ 2 жыл бұрын

Awesome instructions! He was very thorough and I learned some things. And like a true electrician, he never mentioned cleaning up 😅

@joelwalsman773 Жыл бұрын

That's hilarious! I've tried to improve regarding specifying clean up in my vids 🙂

@zTribalstylerz Жыл бұрын

🤣 haha yasssssss

@paulfromcda8440 Жыл бұрын

Sooo well done!! You're a natural. Very inspiring. Thank you.

@ytwhite5930 3 ай бұрын

Very comprehensive video.I'm in the learning mode,so this was perfect.Getting ready to install TESLA charger.

@davidchannell9786 Жыл бұрын

I was taught that it is against code to install Romeo in conduit, besides it’s so hard to pull it through conduit. Stranded thhn wire is the best conductors for this project. You would need to tape the portion every five or six inches that go down the wall unless you can purchase pre twisted wire in the three conductor and size you need. Plus you should have used an industrial cover for the receptacle. It matches the 4 sqr. Box perfectly. The cover you used is for a flush mount.

@thomasmarable6818 Жыл бұрын

Who ever taught you it was against code, should not be teaching. Get a code book look it up for your self. 334 covers NM cable to help you out

@marksmyth9736 2 жыл бұрын

When working in a live panel with or without a fish tape ( finer glass ) I always Cover with cardboard . In this case I would push the card board in on the top right in case I let locknut fall - If would slide out onto the floor . I also squirt some lube in end of the EMT as I install - much easier to pull on long runs and around bends.

@EverydayHomeRepairs 2 жыл бұрын

Not bad advice, thanks for the feedback

@pauliemoto 2 жыл бұрын

Make sure you use that safety cardboard.

@RVTRAILER Ай бұрын

We did it, WE DID IT, Yey! Yes, after watching this video twice, we made some notes and picked parts we needed from the local store (not big box stores) to support the local economy, and we executed this task in under 3 hrs, ran about 45feet wire from the breaker box in the basement to the garage wall. Excellent video, pay attention to instructions and you'll be surprised how easy this task becomes. We followed all codes along the way and yes, that 90 degree L-box at the wall was a tough one to route wires through but we did it. Thank you.

@pld8993 Ай бұрын

If you followed this video in no way did you follow the code. Multiple violations in this video.

@kentlovelace4108 Ай бұрын

You’re a great instructor! Very clear easy to follow and understand. Thanks for sharing!

@rayraycthree5784 Жыл бұрын

I am a diy who has worked on a live panel. As an EE, I have a lot of respect for what is going on it there and take my time thinking through each move before acting. The only time I got stung was while neatly routing the new wires when I touched a hot wire the "pro" who installed the panel had nicked. BTW, that 120VAC sting was nothing like the 300VDC sting I got on my little finger trying to brace a scope probe on a small PCB the size of my fist. I was concentrating on troubleshooting the 5V and 15V circuits on the PCB and totally forgot about the small 300V circuit. It isn't the voltage that kills, you can be electrocuted with just 0.040 Amps of current.

@bryanwhitton1784 4 ай бұрын

I stupidly shorted the 340VDC leads from my 17.5 kWh battery on my home backup system. Exploded in my hands, threw me across the garage and sent me to the emergency room for the afternoon with 2nd and 3rd degree burns. This is not a joke. The thing is, installing these systems in my hardware lab was my job for over a decade. I was installing mine in my home and relaxed on the safety procedures and well I described the results. Safety first.

@paul-andrelarose3389 2 жыл бұрын

Very well done installation! For the benefit of the viewers, I must say that when I cut a conduit, I tape all around it at the desired position of the cut (with masking tape or paint edge tape). I then cut along the tape edge with a hack saw, while rotating the conduit at regular intervals. This keeps the cut always visible on the upper side of the conduit. After the cut is completed, I then remove the tape. This ensures that the cut itself is perfectly perpendicular to the edge of the conduit. This method is particularly useful when cutting large diameter pipes, such as for plumbing drain pipes. 2022/01/11. Ontario, Canada.

@jakeo2600 Жыл бұрын

You do that on a union job, you won't be employed very long,

@pld8993 Жыл бұрын

@@jakeo2600 Do that on any job and you'll be the butt of a lot of jokes.

@bklyn2va2dc 5 ай бұрын

Great, great job! I have watched almost all of the Tesla Wall Connector install videos on KZfaq and yours is one of the best, if not, the best!! Excellent explanation along with very good video showing how you’re performing each step! Ignore the negative comments and keep doing what you do!! Liked and subscribed!!!

@fcatusha Жыл бұрын

The video is excellent, detailed and informative. More importantly are the comments below. Each is very insightful as to this installation. Thanks to all.

@troyfall6573 Жыл бұрын

Hubble also makes the Bryant 14-50 Nema receptacle. The Hubble cost $135 on Amazon and the Bryant cost $46 at Grainger(Model: 9450FR). Exact same product, both made by Hubble.

@jamesreizner2673 2 жыл бұрын

The reason why he had so much trouble pulling is that the EMT he used (3/4 inch) was undersized for the Romex he used (6-3 w/gnd.) 2020 NEC Chapter 9, Table 1 and Chapter 9, Item 9 requires 53% maximum fill for cable in conduit or tubing, which would be exceeded in his situation. So 1 inch EMT, or individual THHN's where 40% fill can be used.

@EverydayHomeRepairs 2 жыл бұрын

Thanks for the feedback James, appreciate the help.

@fernandoprieto2865 2 жыл бұрын

@@EverydayHomeRepairs I tried what James said and it electrocuted my balls off. LOL. Thanks for making the video

@MrBigGStyle 2 жыл бұрын

What's really annoying is hooking up a spa disconnect with 6/3 in a tiny ass box.

@winstonbautista9778 2 жыл бұрын

Exactly

@Blahman240 2 жыл бұрын

@@fernandoprieto2865 This is exactly why some people should just hire some one!

@robmatpol Жыл бұрын

Wow!! What a terrific explainer! Like unexpectedly stumbling into a masterclass.

@Elcapulove Жыл бұрын

Good morning family and good health to everyone. Thank you very much for the valuable information and for your time 👍🏼👍🏼.

@AtomicAJ74 2 жыл бұрын

I used to work as an electrician’s assistant. This was a trip down memory lane. I seem to recall we had to use non-romex when wiring with conduit. Does anyone else remember the same? Also I hated bending the conduits almost as much as running that heavy wire. Kudos to you.

@illestofdemall13 2 жыл бұрын

Yeah, now days we usually use stranded or solid copper THHN/THWN insulated. We generally don't run cables inside of EMT, only single conductors (unless we are sleeving a cable for protection). The guy in this video did a lot of wrong things, TBH.

@wizard3z868 2 жыл бұрын

Most ahj will allow it but you have to account for the outer jacket as fill Also it's sloppy hacky and usually a waste of money over buying a 250 foot spool. My ahj wld have had me strip romex from lb to outlet and required a stub with a romex to emt connecter from lb to panel with a bushing on that connecter at the panel if not a grounding bushing as well lol

@illestofdemall13 2 жыл бұрын

@@wizard3z868 The lack of proper bonding/grounding on the EMT in this installation is a shock hazard. To me that was the most unprofessional and hazardous part of this installation. I am sure he does it wrong all the time, too. Lol

@wizard3z868 2 жыл бұрын

@@illestofdemall13 my ahj would have had me tie in the ground wire of romex to a bond bushing at panel than a bounding at metal lb also (than I wld have had to strip all the romex from lb to the outlet my ahj dosent like romex in emt). I'm sure he bounded at box and outlet thus making all the metal conduit grounded

@jjoejones1 2 жыл бұрын

@@wizard3z868 Bond bushings would not be required for this installation, however the Code does require the equipment grounding conductor to be connected to the outlet box, not the receptacle. Also, Except at terminations, removing the sheath from nonmetallic cable is not permitted in the Code.

@jpwiggo Жыл бұрын

In general your main panel the grounds and neutrals are bonded - if a sub panel they must be separated. In a house there is only ONE location (at the main panel) where neutrals and ground are connected together and attached to a grounding electrode (like a ground rod)

@AztkSmooth Жыл бұрын

I never plan on doing this but thoroughly enjoyed the content. Thanks!

@GeneralTsao86 2 ай бұрын

I watched this video a few times and without any electrical experience I was able to do it in 6 hours. Instead of running Romex throughout I wired individual wires as they were easier (they are lubed) and then instead of the conduit box I used the same deep square box and connected Romex into the dry wall - they also have a follow up video with errors. Also don't buy anything from amazon except the Industrial 14-50 outlet (Bryant and Hubble are the same and Bryant is cheaper) - local hardware store is cheaper Enjoy, Be Safe and Happy Level 2 Charging! Thank you!

@davidrsmith2417 Жыл бұрын

Great vid, thank you so much. Pro electrical engineering tip (Note: we often work in an EE lab with both low and high voltage open equipment with lots of possibility to create a short circuit with any metal objects that might get inside the equipment we are testing) : engineers must remove all conductive jewelry!

@plane_guy6051 Жыл бұрын

Very good advice! Years ago, an electrician friend of my parents died when a ring he was wearing touched a heavy load. Watching the guy in this video was giving me the heebee jeebees because it you get careless for just a split second you can get killed. Much better off to kill the power instead of yourself.

@dido1803 2 жыл бұрын

This video is really awesome!! I learned a lot. Your guest host was great with his presentation. I will keep this video in my must have/see folder.

@joelwalsman773 2 жыл бұрын

It's not perfect and I'm far from perfect, but I appreciate your encouragement!

@tpobrienjr Жыл бұрын

Excellent, well presented. The "look away" at the end was a very good idea. Goggles might be good, too. Thanks!

@tacousa87 6 ай бұрын

if i saw this video 10 years ago i'll be doing electrician job because this is great video very nice Love from pakistan.

@cs_fl5048 2 жыл бұрын

I have done DIY with electrical for 40 years or more, even rewiring a house with a new breaker box in a house out in the country. I am VERY impressed with how thorough and careful with your explanations were. Thank you for this. I do indeed plan to get a Tesla box, but I will probably pay for that to be done. It will be a brand new house and a brand new car. I will not DIY that one...

@d.t.3495 2 жыл бұрын

He really was so thorough…I had to subscribe! I’m an electrician apprentice right now, and at times we’re on a job for months only putting up lights, so this was a great overall refresher on running wire in EMT, fishing wire, plus some pro tips I’ve heard of before but had forgotten about! Why wouldn’t you DIY this with your experience?

@triguer1 2 жыл бұрын

Come on you can do it, a lot of great tips in the comment section on how this could've been a much smoother installation, like using a 4s box instead of the LB conduit, and transitioning through the wall to the panel with flexible metal conduit or better yet using MC cable and avoiding completely the used of the Romex cable, even installing a 5s box with an industrial raise cover for the receptacle.

@yvesn58 Жыл бұрын

@@triguer1 What do you mean with " 4s box instead" ?

@triguer1 Жыл бұрын

@@yvesn58 4s box is a metal box that will be used as a junction box, just like the one he used to put the plug. He should've used one of those instead of the LB. He got into a nightmare trying to run that cable through the LB. There are fittings to connect the wire from the back of the 4s box down to the panel using MC cable, Flex conduit, or even the same Romex cable he used.

@georgepelton5645 2 жыл бұрын

Thanks for making this great informative video. It should be very helpful to new EV owners and to train new electricians [and skilled DIY types]. Given the cost of copper these days, I would install a 6-50 outlet instead of the 14-50. Just be sure to get a 6-50 adapter for your car’s charge cord instead of a 14-50 adapter. This saves the cost of the unused neutral wire. However, if you ever would want to plug in a 50 Amp RV in the future, then go with the 14-50. RVs need the neutral wire and cannot use a 6-50. Another thing to consider is using separate THHN wires to support converting to a dedicated EV wall box with 60 Amp breaker in the future.

@ziamkondkar8273 2 жыл бұрын

Question: Do I run a 6/2 NMB wire for the 6-50 Receptacle . Also should Romex 6/2 wire be in a conduit? Some concerns about heat accumulation in PVC conduit. What do you think?

@fromagefrizzbizz9377 2 жыл бұрын

@@ziamkondkar8273 It’s best to pull individual conductors rather than NM. It’s easier to pull, and reduces potential code issues with the wire overheating - critical if you’re pulling full capacity for a couple hours. In the US you’d be using THHN, and in Canada RA90 or similar. You may be able to use TECK cable (it’s a very heavy armoured cable with an extra layer of plastic) without conduit. While it’s more expensive than NM once you factor in the cost of conduit it ends up no more expensive.

@Allllleeeeeeexxxxx Жыл бұрын

Great Video don’t even have a car, garage and live in Europe with other standards, nothing of this affects me but i still watched the whole thing

@hoogie2004ag Жыл бұрын

This video is awesome! Just installed my home charger thanks to you.

@EverydayHomeRepairs Жыл бұрын

Awesome, thanks for the feedback.

@markg6032 Жыл бұрын

Why do you use 6/3 romex rather than individual conductors? It seems like individual wires would have been much easier to pull and to make the bend in the L-box. Great video and excellent information. Thanks.

@jeffpurdy2347 2 жыл бұрын

625.54 Ground-Fault Circuit-Interrupter Protection for Personnel. In addition to the requirements in 210.8, all receptacles installed for the connection of electric vehicle charging shall have ground-fault circuit-interrupter protection for personnel.

@johndebell2207 2 жыл бұрын

This would require a GFCI breaker?

@jeffpurdy2347 2 жыл бұрын

@@johndebell2207 According to the National Electric Code, yes. Any receptacle in your garage up to 50 amp needs GFCI protection.

@FranklySpeaking73 Жыл бұрын

I have never seen a GFCI for a washing machine nor a nema 14-50 outlet. Someone is making stuff up.

@jeffpurdy2347 Жыл бұрын

@@FranklySpeaking73 It’s called a breaker when it’s above 20 amps. Washing machines have been GFCI required for years.

@jjc355 Жыл бұрын

Very thorough instructions. Another great video.

@karlgolombeski5169 Жыл бұрын

Thank you very much for the very intuitive video production. I picked up a couple. Great tips I can work with. Thanks again. KCG

@dannyboy8850 2 жыл бұрын

Excellent demonstration on the installation. One of the best I have ever seen.

@brady0630 2 жыл бұрын

agreed

@ronmerkus5941 2 жыл бұрын

Wow look at all those home runs running through that center knock out!!!

@Herby-1620 2 ай бұрын

I don't think I would have done it that way, but it got approved. Looks like the electrician was in a hurry.

@keithharrington8715 Жыл бұрын

If you are an electrical pro. Please review the comments here carefully. I only see two possible NEC violations and have worked to provide references below. 1. No ground to the box with the receptacle. 2. Gfci protection for the circut. NEC 625.54 (EVSE) requires gfci receptacle protection for car chargers. This is some time before the 2020 code cycle. NEC 210.8 in the 2020 code requires gfci protection for 250 vac receptacles in the garage. If he is under an earlier code, all is okay is it is not for car charging.

@paulmurray3837 8 ай бұрын

Using a steel fishtape in a live panel? That's sporty!

@rcud1 2 жыл бұрын

This is a good way to do it. I just did a very similar thing for a 40 amp electric heater except I used flexible metal conduit. For me I ran my wire in the conduit and then put it up because that wire is tough to manage. And I just used an outside junction box to near my elect panel to wire it. Really the hardest part is dealing with the thick wire. And just to note, I turned off the power and also bought insulated screwdrivers and pliers to use.

@joeferry2723 2 жыл бұрын

Not correct..not legal..not d Safe

@joeferry2723 2 жыл бұрын

Not good way..illegal..unsafe

@youtube_acct_42 10 ай бұрын

@@joeferry2723 Thanks for the useless comment not specifying which part was illegal or unsafe.

@joeferry2723 10 ай бұрын

@@youtube_acct_42ALL OF IT WAS UNSAFE.

@dunrobincourt Жыл бұрын

Well thought out and presented. Thank you.

@CrazyWillTechShow 7 ай бұрын

Love this video! Great instruction, don’t know if I do the work myself but now I know what to look for. Just got 1 ev.

@EverydayHomeRepairs 7 ай бұрын

Nice! Thanks for the feedback 👍

@andrewbitners4165 2 жыл бұрын

I liked your presentation. When working with a live panel I use a non-conductive fishtape. Although a LB looks nicer, I prefer a 4-11/16 deep j-box above the panel to get a proper wire bend and easy installation. Also I would have stripped the jacket off the Romex between j-boxes.

@paulpoco22 9 ай бұрын

Green fiberglass stick?

@Noah-qt3rq 8 ай бұрын

Pro tip: when fishing wire in a live panel, put a large piece of cardboard inside to cover up all the breakers and feeders. Also wear safety glasses at all times. Where I am, we would not put Romex inside conduit. Run stranded wire and conduit all the way. A “telephone 90” fitting can be used to get into the panel easily.

@user-mx4wq8to8o 7 ай бұрын

Good tips, both. Only a DIYer, but I thought running Romex through a conduit was a no-no, due to its inability to dissipate heat

@kack7130 10 ай бұрын

all these pro tips are a must, thank you

@useemehere2 Жыл бұрын

Excellent teacher for beginner.

@markcrawford8876 2 жыл бұрын

The "some box's" that have the neutral and ground bus's separated, are called Sub Panels! !

@robm3063 2 жыл бұрын

As a union electrician western suburbs of Chicago this is nuts. First off go to Harbor Freight and buy a cheap fish stick set. Next is location dependent . We don't use rope a dope here everything is emt. For all the work you did fishing that wall it would have been faster to make a nice easy offset out the top of the panel and surface mount the whole thing. A little drywall patch and your done. The romex through the pipe was crazy, just buy some wire and push it . I'm not sure if that is even code. I like the idea of EV cars and I know people are shocked (no pun intended) at the cost of 240 install but some things regular folk just shouldn't mess with. Just last month I got tagged doing a friend a favor, Who knew this guys father 40 years ago switched the white wires for the basement lights. Again this was emt and thhn wire. My fault for not tick testing first.

@mmenil1 2 жыл бұрын

Thank you, im from Chicago as well and I thought I was going crazy for telling him to just cut the damn drywall and make the full conduit connection from the beginning to the end. Drywall and some patch work isnt that hard. This is the lazy way to do it and not to code (maybe in his area but not everywhere thats for sure). Disliked video for the lazy work.

@toddmatarazzo5646 2 жыл бұрын

rob m knows whats up

@normandolinic2044 Жыл бұрын

Your a very good instructor. Teacher.

@mujahidhussain8815 Жыл бұрын

Wonderful Information. God Bless you brother. I wish you all the best. “YOU ARE THE BEST”

@bobbarron6969 2 жыл бұрын

Thanks for making the effort that goes into these vids. I learned a thing or two and you knew damn well the experts were going to weigh in on your work. In my handyman work, I've decided to stop at the box, mostly for reasons of liability. But, being able to recognize a correctly installed circuit is very useful and could catch an unsafe situation.

@mikestraker8005 2 жыл бұрын

Add

@dannytorres4388 2 жыл бұрын

Bad install, check out electrical codes . This guy is a fake!!!

@billhandymanbill2775 2 жыл бұрын

Nice video. I would use safety glasses, especially working in a live electrical panel. Secondly, I would use an insulated fish tape while in a live panel.

@EverydayHomeRepairs 2 жыл бұрын

Thanks for the feedback Bill