How to Install a Butcher Block Countertop

How to Install a Butcher Block Countertop | Ask This Old House

Рет қаралды 235,192

3 жыл бұрын

In this video, carpenter, Nathan Gilbert helps a couple replace their laminate countertop with butcher block. Then, he demonstrates how to apply a mineral oil finish to it.
SUBSCRIBE to This Old House: bit.ly/SubscribeThisOldHouse.
What is the Best Wood to Make a Butcher Block?
Butcher block is made from slices of wood that are all glued together into thick slabs, made to withstand heavy daily use. They can be made from nearly any wood, but Nathan chose maple as this is most popular for butcher block counters because it is hard and durable.
What is the Best Finish for a Butcher Block?
Butcher block cannot be left unfinished as it will stain very easily. The only finish Nathan uses on butcher block is mineral oil, a food-safe option that is a must in the kitchen.
It will take about 2-3 layers of finish to start and after that, it needs a layer applied about once a month. Butcher block countertops will give your kitchen a unique, rustic feel while making for a budget-friendly option.
Time: 4 hours to over two days
Cost: $75 to $150 per square foot, not including delivery costs (plus $8 per square foot for professional install)
Skill Level: Moderate
Tools:
Utility knife [amzn.to/39rzE4R]
Prybar [amzn.to/2MdY1dt]
Track saw [amzn.to/36gBhAz]
Circular saw [amzn.to/39qOJDS]
Forstner bit [amzn.to/3qWyGDN]
Chisel [amzn.to/2Mcqrom]
Shopping List:
Butcher block [amzn.to/3tfqMYa]
Wood glue [amzn.to/2MvtyHU]
Joint connectors [amzn.to/3adgnmX]
Food grade cutting board oil [amzn.to/3ou5oL3]
Where to find it?
Nathan installed Unfinished Maple Butcher Block Countertop, which is manufactured by Hardwood Reflections (hardwoodreflections.com/). He ordered an 8’ and 4’ section.
To cut the butcher block to size, Nathan used a TS 55 circular track saw [amzn.to/36gBhAz], which is manufactured by Festool (www.festoolusa.com).
To secure the two sections together, Nathan used Gorilla (www.gorillatough.com) wood glue [amzn.to/2MvtyHU]and Zipbolt (zipbolt.com.au/) UT Joint Connectors [amzn.to/3adgnmX].
In the segment in the Barn after the project, Nathan demonstrated how to finish butcher block using Food Grade Cutting Board Oil [amzn.to/3ou5oL3], which is manufactured by Howard Products (www.howardproducts.com/).
Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free: bit.ly/2GPiYbH
Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet: www.thisoldhouse.com/pages/st...
About Ask This Old House TV:
From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. Ask This Old House helps you protect and preserve your greatest investment-your home.
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldHouseFB
Twitter: bit.ly/AskTOHTwitter
Pinterest: bit.ly/ThisOldHousePinterest
Instagram: bit.ly/AskTOHIG
How to Install a Butcher Block Countertop | Ask This Old House
/ thisoldhouse

Пікірлер: 152

@wesmorris5683 2 жыл бұрын

I love you guys! Y'all have been making it look like I know what I'm doing for twenty years now!!!

@pbenson56fran 3 жыл бұрын

Nice tip on keeping the Butcher Block Countertop up nice for years.

@paulmitrano3612 3 жыл бұрын

Lobstah juice will stain that something wicked.

@Guardducks 3 жыл бұрын

Should have been a tag team Nathan and Richard.

@bsmooth5487 Жыл бұрын

Does everything that a good workbench should. Fold and unfolds with ease! Clamps are sturdy and easy to use. ++++!

@daisyreinacher5022 2 жыл бұрын

I like Rubio monocoat, a hard wax oil to finish the raw wood. Expensive…but worth every penny.

@refiii9499 3 жыл бұрын

Glad to see them using nathan from generation next on his own. Nice easy job for his first job. He has the look and smarts to do well on the show.

@MichaelDawson03 3 жыл бұрын

It is great to see Nathan's involvement with the show continue. However, he has done a few other segments for ATOH since his generation next season. He's been a good addition.

@TOPOM42 3 жыл бұрын

Sure he's being groomed to replace some of the other guys as they get closer to retirement. He's def got a great future ahead

@armyvet8279 3 жыл бұрын

This isn't Nathan's first job. He installed a sliding door in a lady's house before this.

@MegaMatt3 3 жыл бұрын

4:04 Note the back cut Nathan did on the longer piece of countertop. Put a 15-20 degree miter cut there means only the top edge meets the wall, and ensures a nice snug fit. If he'd left it a square cut, and the drywall stuck out more on the bottom than the top, the top would not have fit flush. And that cut is hidden anyway by the second piece the homeowner sticks in (which has a square cut because the cut is visible on the outside end).

@sk6khgcqq8yfho85 3 жыл бұрын

What if the second piece was not flush either? Would you bother with a back cut or would it even look bad with such a small piece? Thanks for the comment, I like seeing people talk about design details

@XtremeGuy-FL 2 жыл бұрын

Smart!

@milocruz6297 Жыл бұрын

What if we hide the line cut ?

@kevreilly7 11 ай бұрын

At what time did he do that miter cut,,,i didnt see it at 4:04.....???

@Pantone268Plus 9 ай бұрын

@@kevreilly7 he's just pointing out where you can see how that cut met up with the drywall

@chrisbaker9173 Жыл бұрын

Awesome thanks

@bigvegass 3 жыл бұрын

Joining the return with an eased edge. Now there's a little trough in the middle of the countertop.

@deerock6846 3 жыл бұрын

waterlox is a food safe finish, I use that all the time

@CountyLineCarvings 3 жыл бұрын

Informative, thanks for posting.

@jeffwilson1399 3 жыл бұрын

No problem!

@baspluim5925 3 жыл бұрын

Pretty much all finishes are food safe once cured. But, polyurethane needs to be sanded before you can apply a maintenance coat, something you don't need to do with mineral oil or salad bowl finish. That's really important. Also, mineral oil doesn't really build "layers", it's more about saturating the wood with oil, and that can take several applications

@Kt-cn2rq Жыл бұрын

Well your supose to mineral oil it every day for a month then I think you do it as maintenance once a or twice a month depending using for food. Eg. Rolling dough. I wouldn't cut on it.

@berneyvonk1 3 ай бұрын

Should have sealed bottom before installation. Also, not rounding corners?

@ianober23 Жыл бұрын

I would have much preferred a miter cut for the corner transition to the little stove piece.

@bumrodgers 3 ай бұрын

Or at the very least have the planks run in the same direction as the main counter. Either way would make it feel less tacked on.

@jeffwilson1399 3 жыл бұрын

Join us for tomorrow's episode . . When Tawmmy an Nahrm re-purpose that over-sized sink cut out into a 2 foot cutting board.

@jeffwilson1399 3 жыл бұрын

You take drugs Danny?

@SouthBaySteelers 2 жыл бұрын

It only took him 5:48 from start to finish. And with no measuring! Of course he used a Festool circular saw. I have a Makita so it’s going to take much longer…probably 3 weeks.

@kevreilly7 11 ай бұрын

Yea they always make it look easy. My walls were not square so i sanded for days,,,smh

@alandickson1629 Жыл бұрын

Yup if you put 2 factory edged together you will get a rut at the join which will collect all the stuff you hate.

@kevreilly7 11 ай бұрын

Every other video i have seen tape the butcher block before cutting

@billybarnard6852 2 жыл бұрын

What about a stain could you put a stain on then use the mineral oil over top of that

@francisyang9997 3 жыл бұрын

Teak is the way to go.. yes it leaves marks if you actually butcher ..but you don’t have oil it all the time ....

@sydneymviera Жыл бұрын

Most finishes are food safe once cured. Think about your dining room table. Sure, you wouldn’t cut directly on it, but you’re not gonna throw out a piece of food that touches it.

@T00tsybutt0ns 10 ай бұрын

Good point.

@GaiusGarage 4 ай бұрын

if you use mineral oil to seal it, you have to keep applying it once a month forever?? seems like a huge pain

@Will_JJHP 11 ай бұрын

Mineral oil is a major endocrine disruptor. I prefer melting food grade beeswax in with MCT oil as a non toxic wood sealer

@ericlovesyou8910 7 ай бұрын

Interesting comment for this video! I’m going to be installing my butcher block soon and have been wondering if there are harmless, natural alternatives for sealing. Much appreciated

@hdwblade 2 жыл бұрын

He mentioned that we can get a mineral oil with Tung oil.... What is that? And from where?

@moe4490 Жыл бұрын

Can anyone tell me if I can use a masons miter on butcher block?why/why not?

@musiqman24 3 жыл бұрын

Question, with a mineral oil finish, I had the understanding that once the wood can no longer absorb any more oil, it'll just stay on the surface. So wouldn't that mean you actually can't build up protective layers?

@micahbush5397 Жыл бұрын

The oil will continue to penetrate deeper into the wood; short of submerging the wood in oil for an extended period of time, it's doubtful that you'll ever saturate the wood, especially since some of the oil will come out when you wash the countertop.

@jjyemg2397 Жыл бұрын

Butcher block oil is better and lasts longer and doesn't have to be applied as often as mineral oil.

@robertbamford8266 3 жыл бұрын

I wonder about sealing the seam where the new counter needs the old backsplash. Not trivial - and probably should have started before the new counter was slipped in place.

@Guardducks 3 жыл бұрын

It will be sealed by a thin bead of silicone, which i hope Nathan did before he left.

@chrisburns5691 2 жыл бұрын

sillicone after install.

@kevreilly7 11 ай бұрын

All these "experts" forget to mention what to do when your walls are NOT square

@MHamlin30 4 ай бұрын

Look up “scribing” 👍

@kevreilly7 4 ай бұрын

@@MHamlin30 thank you. My point was all these experts think everything goes smooth

@JonDunnmusician 8 ай бұрын

Has Festool track saw, yet no Domino 700 to join the pieces??

@ironheadhooligan Жыл бұрын

❤

@serge.crispino418 3 жыл бұрын

In my neck of the woods that stuff is called 'Block Board' - most of it comes out of Asia - it's cheap - finish it properly and it will serve you well.

@kevreilly7 11 ай бұрын

Cheap?? Ya get what ya pay for

@bigmarc977 3 ай бұрын

He should applied some starter coats of mineral oil before install

@johnnywood8082 3 жыл бұрын

Like the new camera work

@johnnywood8082 3 жыл бұрын

@@Kevin-mp5of really? You should look into that.

@johnnywood8082 3 жыл бұрын

@@brianglade848 agreed.

@johnnywood8082 3 жыл бұрын

@@Kevin-mp5of English please?

@johnnywood8082 3 жыл бұрын

@@Kevin-mp5of 🤡

@johnnywood8082 3 жыл бұрын

@@brianglade848 It’s English but not proper it’s unintelligible.

@DWMtukwila 2 жыл бұрын

I am a bit confused. You secured the countertop solidly with screws. Does that allow for expansion? Won't it crack or is expansion contraction not that important? I am in the process of doing this now and a newbie who is watching and reading everything I can. Thanks

@TheTurbomopar 2 жыл бұрын

Confused as well

@IndianaJBird Жыл бұрын

Hey there should have been at least predrilled holes. About 1/2” and center the screw with a washer in the middle.

@ChubbyUnicorn 11 ай бұрын

Wood onlybexpands lengthwise/along the grain it doesn't expand across grain. The dogbone connectors allow lengthwise/along the grain expansion & screws are set across grain where expansion isn't an issue.

@dylanlane9405 10 ай бұрын

@@ChubbyUnicorn You need to do some research bud. wood expands and contracts in width. wood will barely move in length

@gkatz9867 3 жыл бұрын

"It's not in my lipstick, pal."

@thesawshackredemption8236 Жыл бұрын

I can’t believe he ran straight screws into this from the bottom. You NEVER screw solid wood tight as it doesn’t allow for movement. If you do use screws make sure and drill a large pilot hole, say 1/2” and use a washer, this allows the wood to still expand and contract. Also, finish before you install 🤦‍♂️🤦‍♂️🤦‍♂️

@LobeSmash 11 ай бұрын

How do you secure screws to a hole bigger than the screw. Seen this comment a few times without any meaningful explanation.

@nismo613 3 жыл бұрын

Who applies mineral oil with a knife like that?

@randomreviewz 3 жыл бұрын

Coming up next: Ripin out the whole kitchen because it looks like a Camp Crystal Lake cabin

@roberthendricks1453 4 ай бұрын

😂😂😂

@jasonargentieri8954 3 жыл бұрын

Next remove the tile and replace.

@iposttvshows 25 күн бұрын

I'm about to have butcher block installed and my guy wants to use 2 part epoxy for sealing. I don't know the brand yet, still waiting for him to let me know so I can source it. Any thoughts on Epoxy?

@kcChicken123 10 күн бұрын

The absolute best finish. I have epoxy and nothing can stain it. You don't have to worry about water from my the sink and washing hands. It's indestructible. Ask about UV additives to prevent yellowing over time. Epoxy is king in the kitchen

@pierremitham2964 3 жыл бұрын

Would have liked to see an epoxied mitre for the return. Looks much better

@jeangibsonmedley Ай бұрын

I use tung oil, not a tung oil blend but 100% tung oil

@kurtbilinski1723 2 жыл бұрын

Most butcherblock is 1.5" thick. The old countertop material was much thinner, so something happened behind the scenes to allow the new material to magically fit under the back splash tile.

@chrisburns5691 2 жыл бұрын

laminate counters are built up thinner around the edges.

@johnp82 3 жыл бұрын

Whoever put the music on this should be fired.

@brotha4luvin 3 жыл бұрын

😂

@slick.adventures 3 жыл бұрын

I do have to ask, with butcher block. The way it's anchored, shouldn't it be mounted in a way that allows for wood movement expansion/contraction? It looked like he just screwed it in tightly

@theaceofspades39 3 жыл бұрын

It's indoors. As long as the wood is completely dried to the humidity inside the house there shouldn't be an issue

@TheTurbomopar 2 жыл бұрын

@@theaceofspades39 🤔 my house varies from 70% humidity in summer to 30% in winter. Still no issue?

@wwfera00 Жыл бұрын

Expansion brackets.

@ChubbyUnicorn 11 ай бұрын

Wood expands lengthwise not width wise the dogbones allow for length expansion, the screws are set widthwise where there isn't expansion.

@dylanlane9405 10 ай бұрын

@@ChubbyUnicorn again do some research. wood expands more in width

@PinkSlippers70 2 жыл бұрын

wow, I can't believe he didn't put at least 4 coats of sealer on all sides edges and end cuts...he then screwed the whole thing in and tells the owners to put a finish on it...they will never be able to seal the whole thing now...you seal it BEFORE installing

@Kt-cn2rq Жыл бұрын

What kind of sealer do you use? Won't it go dry after you seal the sides especially against the wall?

@goldenarrow3 Жыл бұрын

@@Kt-cn2rq We used Tung oil, several coats at least, both sides before instalation

@kevreilly7 11 ай бұрын

Thats i watch multiple videos of different people

@Gardens4Life 7 ай бұрын

I used WaterLox on my butcherblock counters. After drying and curing, it’s food safe and waterproof. We don’t cut on it, though. For all that time and money, just use a cutting board. 😊

@jcbrotherhood 6 ай бұрын

It has to be back painted at least You can’t seal just one side or it will potato chip on you

@Homepros888 3 жыл бұрын

He should have got a bigger end piece and make a miter cut it would look so much better than the way he did it.

@ar15tac Жыл бұрын

Yes but I imagine this was a very limited budget project. They didn’t even have contractor finish the top.

@iamthepeterman54 3 жыл бұрын

Come on Jared.

@gpslightlock1422 3 жыл бұрын

The next generation takes the reins.

@RevolutionPaulRon 2 жыл бұрын

Heat resistant resin and flood coat that b

@thelostarchivesserialvault5353 3 жыл бұрын

Mineral spirits is food safe and will do a good job sealing the counter. If they are smart they wont do any cutting on that counter and only on the block cutout...

@trobbins0000 3 жыл бұрын

Mineral oil....

@jeffwilson1399 3 жыл бұрын

@@trobbins0000 same difference! Lol

@bblakester69 3 жыл бұрын

Nope, mineral oil!

@jeffwilson1399 3 жыл бұрын

@@bblakester69 it's a joke dummy. Hence the lol.

@trobbins0000 3 жыл бұрын

@@jeffwilson1399 mineral spirits would add a nice kick to your food. 😁

@johnlehman4614 2 жыл бұрын

Can we get the guy some light to work with in that kitchen

@GerardoGarcia-tb7gi Жыл бұрын

Wutung oil and polyurethane are food safe.

@WouterZtube 3 жыл бұрын

What the h... is going on with that island countertop?

@alopardo 3 жыл бұрын

That looks absolutely horrible without mitering that cut.

@DavidOliveira-gy2dg 3 жыл бұрын

I picked up on that too. Countertop is beautiful. Maybe a miter with a jointer connection? Or dowels to bind it?

@alopardo 3 жыл бұрын

@@DavidOliveira-gy2dg literally anything!! The pattern of the wood takes a complete 180 turn and looks really really bad.

@Trd2020 2 жыл бұрын

Never showed how he bonded it?

@iggysixx 3 жыл бұрын

To the editors: Those super wide angle lens shots are pretty sweet. And I love the cinematic shots (that a previous commenter already mentioned). There's some beauties in there (the close up shots of tools, the dark lit circular sawing in the kitchen) - seems like you're fully exploring the possibilities of - (what i suspect is quite the expensive :)) new lens. It be nice if you could lessen the bubble effect - (..of the indoor overview shots in particular) - a bit in post production, though. You should be able to do some lens correction quite easily in your editing software (to straighten out the 'fish eye' effect a bit, without losing the overview of the shot) That would also make it a little easier to keep your horizon level in the shots. (In film - a skewed horizon & distorted proportions are normally used to signify "inner turmoil" or a 'disconnect with reality' in the actor. Most viewers will have that internalized / will "feel" that there is something 'off') If the lens correction is too much work; maybe only make the horizon level in the center of those shots. That would make some difference already Other than that - looks good. Very interested to see how this film style will develop as you guys become more familiar with the lens, and everything becomes second nature. Keep up the good work :)

@borys444 3 жыл бұрын

@@brianglade848 Kevin left u talking by urself cause he deleted his comments..

@that_old_white_guy6732 3 жыл бұрын

Happy wife, happy life. The Mr. doesn't have to do anything by write the check. The Mrs. is as happy as a clam in wahm watah.

@that_old_white_guy6732 3 жыл бұрын

@@brianglade848 1792 bourbon, my friend.

@Lamborgini112 3 жыл бұрын

Does Kevin seem like he's super tired to anyone? Did he just get over the Rona or something?

@davidc8560 3 жыл бұрын

He definitely sounded different. I had to do a double take to see who was talking.

@brianjones4904 3 жыл бұрын

Anyone else concerned about that plunge cut he made with a circular saw?

@bigvegass 3 жыл бұрын

@chrisburns5691 3 жыл бұрын

why would you be concerned about that?

@Trd2020 2 жыл бұрын

I would rather do polyurethane just don’t cut food on it

@mae2759 3 жыл бұрын

"It's so easy, Kevin can do it."

@spirospappas2516 3 жыл бұрын

Should have used under mount sink.

@bmac1629 3 жыл бұрын

Not in wood lol, but what he should have done is cut the hole for it outside...why bring it into the customers house and make all that extra dust, and you can have 360 access around the top outside.

@chrisburns5691 3 жыл бұрын

@@bmac1629 also i would have sealed the counter at least one coat after the cut out and before installing the sink, give it some protection if waters gets in under that flange over the years.

@derewreck 3 жыл бұрын

Kevin isn’t the young buck he once was.

@rodgerq 3 жыл бұрын

If he gives that lipstick a go he might look a bit younger 😜

@Fusiongearz 3 жыл бұрын

I would totally cut on those counter tops so they look nice and ugly later with a bunch of knife marks

@carlostosado8965 3 жыл бұрын

I made a cutting board out of extra butcher block I had

@theshop5331 6 ай бұрын

chip and flake over the years....so lame every material has its pros and cons, comes down taste and cost save up a few years and use solid strip butcher block, relegate the finger joint crap to the garage work bench elongate the screw holes to allow for some expansion contraction

@finianbower8615 3 жыл бұрын

341st

@wontonpickup Ай бұрын

A big N-O to the mineral oil. It didn't work on my hevea wood at all. I had to re-seal it. Used Watc and am happy with that. Yur bad advice cost me a lot of time.

@mitchd949 3 жыл бұрын

The entire backsplash flexes horribly at 2:02. Do it right and replace that awful backsplash too. In for a penny, in for a pound as they say!

@kearnsey64 3 жыл бұрын

Who the hell are these guys??

@jeffwilson1399 3 жыл бұрын

Beavis and Butthead. . . 🤘🤘🤘

@juliof970 3 жыл бұрын

Cheap replacements with less talent

@juliof970 3 жыл бұрын

Tom Silvas' replacement is a joke

@andrewhouse6296 3 жыл бұрын

This isn’t an ATOH video. Shots intentionally blurred, weird upbeat music, and no explanation of the actual carpentry steps. Gahbage.

@TheRealRedStripe 3 жыл бұрын

First

@quentincrisp6933 2 жыл бұрын

That's one depressing kitchen!😂

@scundoorsup5342 3 жыл бұрын

Meh

@becomingholistics8731 3 жыл бұрын

“Not in my lipstick!” Nothing like a dash of fragile masculinity, fella.

@peterjoseph8974 3 жыл бұрын

Garbage work. 45 that corner.

@chrisburns5691 3 жыл бұрын

what would the advantage be to miter the corner?

@wraypaul566 3 жыл бұрын

Been agonizing about butt joints vs 45 miters on mine. I have a track saw so cuts are no problem. 45 degree lets you glue the pieces together without worrying (as much) about wood expansion/contraction. If the individual boards are all the same width and the grain/color are similar, a miter joint will look really good & look like it flows around the corner. I’ve seen some on the interweb where that wasn’t the case, and they look terrible Butt joints at 90 degrees don’t flow, so the joint looks amateurish. Also, opinions vary on whether to glue them. At 90 degrees, one “board” swells one way and the other swells the other. I dont see how you can glue them without something coming apart. Maybe only at the center like a breadboard table end? Other problem with butt joint is that you have to rip off the rounded edge on the long piece or you get a gap in the joint. Ripping a 12’ piece of butcher block isn’t something I’d want to do on a table saw. Track saw should be just fine, though

@kevreilly7 11 ай бұрын

Wow demo.with no gloves on....smh

@jeffwilson1399 3 жыл бұрын

$9000 Festool track saw. . And they show one cut. . That takes 20 seconds.

@rodgerq 3 жыл бұрын

You're shopping in the wrong places my friend.

@wraypaul566 3 жыл бұрын

My Makita corded track saw with an upgraded track was way less expensive and does a beautiful job