How to Properly Paint Your Kitchen Cabinets

How to Properly Paint Your Kitchen Cabinets | Ask This Old House

Рет қаралды 448,244

2 жыл бұрын

In this video, Ask This Old House painting expert Mauro Henrique shows host Kevin O’Connor the proper way to paint cabinets for a new, updated look.
SUBSCRIBE to This Old House: bit.ly/SubscribeThisOldHouse.
Kevin O'Connor meets expert painter Mauro Henrique back at the shop to tackle a kitchen cabinet painting project. Mauro plants to show Kevin how to prep the cabinet, prime it, and coat it with a durable paint designed for the job. And while the two are working on just one cabinet, they discuss how to scale the project for much larger projects.
Skill: ⅕
Cost: Less than $100, depending on the number of cabinets
Time: A weekend, depending on the number of cabinets
Shopping list:
Degreaser spray [amzn.to/3F2mg4f]
Latex primer [amzn.to/3bXPswD]
Water-based trim and cabinet enamel paint [amzn.to/3qrXsPe]
Roller sleeves [amzn.to/3qrZUVW]
Tools:
Screwdriver/screw gun [amzn.to/304FE1j]
Permanent marker [amzn.to/3ksKs7Z]
Rags [amzn.to/3kmwy7d]
Foam sanding block [amzn.to/3CaRTXG]
Tack cloth [amzn.to/3oaUago]
Paint tray [amzn.to/3qow7NN]
Paintbrush [amzn.to/2YEmxLi]
Mini paint roller [amzn.to/3F5z4He]
How To Properly Paint Kitchen Cabinets
1. Start by using the screwdriver or screw gun and removing the drawer pulls, doorknobs, drawer fronts, and doors. Be sure to mark each drawer front and door with a marker to prevent mixing up the doors. The best place for this mark is behind the hinge location.
2. Clean the cabinet by spraying it with a degreaser solution and wiping it down with a rag. This removes all the oils and grease that could prevent a perfect finish.
3. Use a foam sanding block to scuff the surfaces of the cabinet, drawers, and doors. This is a light sanding meant to give the primer something to adhere to, so don’t sand to the bare wood. Use a tack cloth to remove the sanding dust before moving on.
4. Pour some primer into the paint tray and load the roller and brush. Using the brush along the edges and tight spots, and the roller on the large, flat surfaces, coat the cabinet, doors, and drawer fronts with a coat of primer. While you’re allowing the primer to dry, wash your brush and roller sleeve, and pour the excess primer back into the can before washing the paint tray.
5. Pour some trim and cabinet enamel paint into the paint tray and load the brush and roller with paint. Use the brush to cut in along the edges, push paint into the corners, and leave out roller strokes. Use the roller to apply enamel paint to the large flat surface where possible. Cover the rush and roller with plastic bags to prevent them from hardening while you wait for the first coat to dry.
6. Apply a second coat to the cabinet. This coat should provide a perfect, consistent finish without any thin or light areas where wood might show through.
7. Once the second coat dries, reattach the door and drawer fronts. Enjoy the fact that you’ve given your kitchen cabinets a fresh new look without investing a lot of time or money.
Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free: bit.ly/2GPiYbH
Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet: www.thisoldhouse.com/pages/st...
About Ask This Old House TV:
From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. Ask This Old House helps you protect and preserve your greatest investment-your home.
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldHouseFB
Twitter: bit.ly/AskTOHTwitter
Pinterest: bit.ly/ThisOldHousePinterest
Instagram: bit.ly/AskTOHIG
How to Properly Paint Your Kitchen Cabinets | Ask This Old House
/ thisoldhouse

Пікірлер: 411

@FallLineJP 9 ай бұрын

Every time they were painting right up against the marble without masking it off my heart skipped a few beats 😂

@YAWN.... 8 ай бұрын

You obviously dont know how to paint...

@coblaze1 3 ай бұрын

thats not marble. its laminate

@DumptruckFullOfMidgets 19 күн бұрын

@@coblaze1 You know what they mean, quit being a nerd.

@coblaze1 19 күн бұрын

@@DumptruckFullOfMidgets lol no

@SapphireA. 10 ай бұрын

Thank you. I just watched a handful of tutorials and this one was by far the easiest to follow and understand.

@JeffersonMartinSynfluent 2 жыл бұрын

The slo-mo out of focus shots remind me of Martha Stewart cooking shows from twenty years ago. Thanks for the nostalgia.

@weekendhomeprojects 2 жыл бұрын

I'll be doing a light (current home, future rental) remodel on my bathrooms. Just stopping by to see what painting one of these cheap oak cabinets entrails. Looks pretty easy fellas. Thanks for sharing.

@warrenvalentino5763 2 жыл бұрын

Thank You Very Much for this video. i always wanted to paint my kitchen cabinets. but i realy did not know how to. i have watch this old house and ask this old house on pbs and mpbs right from the very first show. all of you are Awesome! :)

@gary24752 8 ай бұрын

Insul X has both the bonding primer and Cabinet Coat both which are manufactured by Benjamin Moore. The Insul x primer is one of the best on the market.

@almazabraha 2 ай бұрын

The best video on painting cabinet thank you

@nick4leader 2 жыл бұрын

I wish I could paint my cabinets up in the air like that

@Off-Grid 2 жыл бұрын

Well you could remove all the cabinets....

@devdhamija7585 2 жыл бұрын

"Telekinesis is tacky."

@Fattony6666 2 жыл бұрын

oh no! You will have to bend a little. Are you going to be ok?

@nick4leader 2 жыл бұрын

@@Fattony6666 probably not

@roberto3262 2 жыл бұрын

You can. Just lift them up and set them on some stolen milk crates.

@stephane184 2 жыл бұрын

Planning to do this as well. Same principal applies for particleboard laminate cabinet cases? Doors are maple shakers but cabinet box is a laminated particle board

@rchukran 2 жыл бұрын

This Old House has always been an entertainment program. It has never been a how-to program. So I've been entertained by the pros dissing the job that Mauro and Kevin have done. Like : Man, I'd get fired if I did a job like that. I'd use a sprayer... I'd do this and that. The reality is that a handy homeowner would never hire a pro to do this small a job ( 10ft of cabs or so). I am such a homeowner that has painted dozens of feet of my own cabs in 5 homes. This is basically how I did them. No spraying, and certainly no pore filling. And as for the people whining about what brand of this or that, or how do I buy a brush or roller, you are not ready for this job yet. Go buy some cabs for the garage and practice on those. A 20 minute video is not going to teach you how to paint. Painting a few is going to teach you how to paint. As for me, I was satified with the video. First, it is free. Second, it was entertaining. Third, I did not need to learn anything from it.

@Briguy1027 2 жыл бұрын

Ah, okay. I was wondering why they didn't use a sprayer. I was wondering if this video would help me touch up my cabinets, which were sprayed. And now I know, the answer is no, LOL.

@ivanlara5815 2 жыл бұрын

Well said Sr!👍

@itomba 2 жыл бұрын

True, no homeowner will be able to master the technique of spraying the cabinets for just his one kitchen project. But I have seen the painter we use for our home improvement business use a Benjamin Moore product called Cabinet Coat that brushed on and smoothed out into a spray look finish.

@Fattony6666 2 жыл бұрын

@@Briguy1027 that's not funny at all

@JohannGambolputty22 2 жыл бұрын

You absolutely do not need to spray to get a professional look but you do need more prep than This Old House video. This is a must watch where a true professional will explain the different primers, paints and technique to use in order to get a perfectly smooth finish: kzfaq.info/get/bejne/ZtF7d8Wm2bfGpJc.html

@ritaalbazy1264 Жыл бұрын

Beautiful easy job

@kcstoneguy Жыл бұрын

Thanks just what I needed to know

@user-je7og2mc7c 3 ай бұрын

Thanks - very inspiring!

@timmorgan3164 2 жыл бұрын

I love this old house but this video is definitely geared towards home owners. If you have a sprayer it definitely helps with a high quality finish. We use a primer like zinzer cover stain or an oil based primer then cover with Sherwin Williams Pro classic with alkyd or PPG Breakthrough for final coats but ask your paint store about cabinet grade paint. They will know what works best.

@soliloquys 2 жыл бұрын

Will behr marquee paint work on a cabinet?

@josiahamaze Жыл бұрын

@@soliloquys I wouldn't suggest it. Search some videos here in KZfaq for best Cabinet paints.

@amigos4erin 9 ай бұрын

@@soliloquysyou don’t want to use wall paint on cabinets or furniture; it will peel off with use. I mostly shop at Lowes (much closer to me) so I’m not familiar with the Marquee line, but look for a cabinet/furniture paint line.

@rosecocchiarella2009 4 күн бұрын

@corteltube 2 жыл бұрын

Great job guys…looks great…I am getting ready to do my cabinets…I know it will not be easy…clean…sand prep…but it will be worth it to do it the right way. That golden oak has just got to go…I have a simular countertop…so this helps a lot…love the color.

@DctorSkillz1 2 жыл бұрын

It won't be worth it. From maybe ten feet away, it looks good. If you're a foot away, it looks poorly executed.

@dylan-nguyen 2 жыл бұрын

Buy yourself a corded random orbit sander to do 90% of the work And if u got the budget Wagner flexio spray painter You’ll get a 95% quality factory finish. Prob even better than the cheapo finished cabinets at Home Depot and IKEA

@DctorSkillz1 2 жыл бұрын

@@dylan-nguyen I disagree. The stock cabinets they have at Lowe’s are really good for the price. You’ll never even get close to the finish if you attempt to repaint your old cabinets.

@suncasa2224 9 ай бұрын

Great video. And I think, “hmmm, I could do that.” 😊

@scottyellis3442 2 жыл бұрын

Just did the same project a few weeks ago myself, I degrease sanded but I used oil based primer and oil topcoat. Two coats each.

@anthonyszeto5508 2 жыл бұрын

good choice.. a better-looking finish.

@scottyellis3442 2 жыл бұрын

In my opinion oil is a much more durable paint. Plus I sprayed, no roller or brush.

@shanew7361 2 жыл бұрын

@@scottyellis3442 Yep

@shanew7361 2 жыл бұрын

@@anthonyszeto5508 Yep

@Off-Grid 2 жыл бұрын

@@scottyellis3442 spraying is better

@Nugs59 2 жыл бұрын

Haha he was so proud of how much he was cleaning off he kept showing his buddy

@politicalpartyagnostic268 2 жыл бұрын

Nice teamwork

@ln14517 2 жыл бұрын

I've worked at the paint store and have done this exact job multiple times. be sure to do your research and make sure the job is done properly. People tend to overlook and not be prepared.

@DtKnize 8 ай бұрын

Zinser Smart Prime and Benjamin Moore Advance are awesome products for kitchen cabinets.

@Phamtom009 2 жыл бұрын

Shellac and Oil-Based Primers are superior. If you find bleed through after your water-based paint job, you can go over with Shellac Primer and repaint. Worked well for me.

@njmallday 2 жыл бұрын

Water based poly like Renner is superior.

@remodz6385 2 жыл бұрын

This may be true for a new build/raw wood. But this wood has already been sealed for years and probably a very thick coat of seal considering the look of them once they scuffed them. Any primer will do. And if refinishing cabinets, a water based is best because it’s in your kitchen. An oil based would stink the whole house up for days to weeks.

@prophecynewschannel7398 7 ай бұрын

@@remodz6385 everything you said is false lol. You need a shellac to seal up tannin bleed or it will never cover. I BIN every set of cabinets i do and it stinks only for a few hours, not days or weeks lol. Any primer WILL NOT WORK

@woojalitus 2 жыл бұрын

Slow mo shots of paint drying….very informative

@quarantainment293 10 ай бұрын

BIN Shellac primer is my favorite for cabinet so far..

@edmc755 6 ай бұрын

Super Job. Do you have to fill the wood grain first ???

@alfredoandroid357 2 жыл бұрын

Thank you, great video I am definitely not going to paint my cabinets, lol 🙃 😅

@RichardGreco 2 жыл бұрын

Excellent video. The people who owned our house before us painted the kitchen cabinets. They did not follow Mauro's steps. More painting videos please.

@weekendhomeprojects 2 жыл бұрын

What was noticeable about the previous home owners paint job?

@DiannaAtherton 6 ай бұрын

Razor blade and done

@richardmoss5934 Жыл бұрын

If you have 20 cabinets as Kevin said why not just do one at a time, then you don't have to worry about where to put the contents!

@GentsConstruction 2 жыл бұрын

There’s an additive called Floetrol to help eliminate roll and brush marks lol

@Fattony6666 2 жыл бұрын

that's not even remotely funny

@stytos 10 ай бұрын

I can't help but feel like some time in this video would've been a great time to make a "happy little accidents" reference. Still, we're going to be painting our cabinets, so this video helped. Thanks!

@nataliejones7585 Жыл бұрын

Just watched the first fee minutes...how do you prepare the sides which are usually laminate? Do you sand laminate as well? Not sure if that's addressed here. Thanks

@jogrin 2 жыл бұрын

Y’all get a new camera? Some amazing close shots in this video.

@JustinWalker77 7 ай бұрын

Should the base trim and 1/4 round be painted to match the cabinets?

@Travis21G 8 ай бұрын

So I need to clean/wash before? Or if I’m sanding them down thoroughly does it really matter? Any downside to using electric sander?

@cirrus820travelers9 Жыл бұрын

Can you use all-in-one primer/paint product?

@carrolllehnhoff-bell2177 Жыл бұрын

Excited to give this a try! What degreaser did you use?

@sevensages5279 Жыл бұрын

Krud Kutter All purpose Cleaner/Degreaser. It's the red spray bottle. Good luck on your project!

@jaym1244 Жыл бұрын

I used TSP(Trisodium Phosphate), worked excellent.

@kippywylie 2 жыл бұрын

I need a video on how to adjust the hinges when reassembling because I can't get this right

@danb.709 2 жыл бұрын

I'd highly recommend a high bond primer, if going over any sort of clear finish. Also be very careful and consistent with your brush and roller strokes, texture is very important on something like a cabinet. Also no satin in a kitchen, it attracts too much oil and dirt.

@edgarromero8551 2 жыл бұрын

Actually the steps he did was good, but I prefer cover stain from zinsser

@Off-Grid 2 жыл бұрын

I'd spray vs brush

@danb.709 2 жыл бұрын

@@Off-Grid that is not an option for some people in some situations.

@ryane6719 2 жыл бұрын

Lol, satin is the industry standard finish.

@danb.709 2 жыл бұрын

@@ryane6719 maybe for a clear finish, satin paint on a high wear surface will attract more dirt than a semi gloss, as will a semi gloss more than a gloss. If that is what you want for your own home sure, but I manage apartments, satin would not last an acceptable amount of time.

@akashdeep6355 2 күн бұрын

Do you use brush after used roller?

@iair-conditiontheoutsideai3076 2 жыл бұрын

I wish they made something like this for RVs like ask this old RVer or something. Lol

@germanchavez8204 2 жыл бұрын

I recommend X.I.M primer from dunn edwards it's 50 bucks a gallon but it hold perfectly. As far as paint goes I have had very bad luck with Behrs Alkyd that they used scratched up real easy even with primer.

@shanew7361 2 жыл бұрын

Behr is dog 💩

@germanchavez8204 2 жыл бұрын

@@shanew7361 I mean I didn't wanna say it like that but yes. It sprays on great but rolls on horribly.

@dmondra2 2 жыл бұрын

They're sponsored by HD so that's why they likely picked Behr. I think the take away here is that you need an alkyd paint if you want low VOC, are diy, and looking to avoid oil based products (as most diy folks typically do). Benjamin Moore Advanced would have been my pick.

@germanchavez8204 2 жыл бұрын

@@dmondra2 I believe the reason for Behr is because it comes from a "dyi" store. Most people who diy don't really go to paint stores they go to the big box stores.

@ryane6719 2 жыл бұрын

XIM UMA is hands down the best acrylic bond coat made.

@chrisnash2154 2 жыл бұрын

I’m sure that I am chiming in on the same thing others have mentioned. It doesn’t look like anything was done to hide the grain, yet I didn’t really see any grain after painting.

@Off-Grid 2 жыл бұрын

Probably because the paint was an enamel made for cabinets. Not your basic paint.

@nycfrank 2 жыл бұрын

Paint on wood will always hide the grain, doesn't matter the kind of paint. The only way to keep the grain is to stain the wood.

@Fattony6666 2 жыл бұрын

why would you worry about the grain???

@nycfrank 2 жыл бұрын

@@Fattony6666 in some some cases people stain the wood because the color of the stain and the grain of the wood make a nice look

@klaus3794 7 ай бұрын

There is painters tape in this world!

@Samsonmetaphysical 2 жыл бұрын

Dunn Edwards BLOCK-IT PREMIUM for the primer and Dunn Edwards ARISTOSHIELD for the paint. If you own a house you can afford a HOMERIGHT FINISH MAX SPRAYER so now you can spray those cabinets, they are only around one hundred bucks.

@annebarone1019 2 ай бұрын

I hope I get a response. In materials it says 4 inch roller sleeves, high density. Then at the end of list it states Mister Rui Paint Rollers 4 inch polyamide. Is one for the primer and one for the paint? It doesn't indicate why two different types. Thank you in advance.

@PoopaJEM Жыл бұрын

Do you paint the inside of the doors?

@classicrise1 3 ай бұрын

great vdo

@risingsun82 10 ай бұрын

Hi, what roller do you use?

@barryphillips1958 Жыл бұрын

it looks good on video, but when finished are there brush stokes or brush marks on the doors?

@jeffd.6163 2 жыл бұрын

You really need to tell more specifics in these videos. What type of roller? What type or brush? How about brand of paint used?do you brush it after roll? Come one

@rickfromthecape3135 2 жыл бұрын

Yep. All the painting videos are like this.

@shanew7361 2 жыл бұрын

Yep

@Off-Grid 2 жыл бұрын

They could put it in the description

@jm100368 2 жыл бұрын

the paint was behr cabinet and trim

@fisherman2359 2 жыл бұрын

You’d be a lost puppy without them huh.

@Skebtik 2 жыл бұрын

Don't let them lie to you. You definitely 100% need to use oil primer if you are not going back to bare wood. Even alkyd or urethane won't stick to a light scuff sanding. If it doesn't pass the fingernail test after 48 hours what do you think like it's going to look like in a year?

@TheRogueDeadGuy 2 жыл бұрын

That's nonsense. Oil isn't necessary anymore. It also takes closer to 3-4 weeks to establish a true density. Guaranteed it passes the scratch test after a month. I've used Latex primer on every cabinet job I've ever done. If you follow the proper Prep methodology, you'll be fine 👍

@Skebtik 2 жыл бұрын

@@TheRogueDeadGuy unless you're removing ALL sealing of the grain we will agree to disagree. Care to name your product? Most (like +90%) of paint reps will tell you, you have to strip the surface 100%. Many write directly on the can. I'd really like to know what you're using that isn't. I'm skeptical at best. True density? We are talking about adhesion.

@broodyyedda5621 2 ай бұрын

@@SkebtikI like your thinking. I'm gonna do this but cause of money issues I can only afford a sander/ vacuum for the sander and the stuff these guys are using. Do you recommend the oil primer at least? Also does the oil primer have fumes?

@Skebtik 2 ай бұрын

@broodyyedda5621 well I down own a run a painting company

@broodyyedda5621 2 ай бұрын

@@Skebtik will it at least be better if they sanded it a bit more and put more layers of.primer?

@rogerthedodger5788 Жыл бұрын

@ 4:02 do you have to paint this slowly? Slow motion? Or is this a badly chosen video effect? Great video nevertheless as planning to do this job soon.

@javiergalvan242 2 жыл бұрын

Great video as always 👍

@rickfromthecape3135 2 жыл бұрын

Great cinematography, nice guitar music.....no instruction again from the painter.

@bunny1979 2 жыл бұрын

Thoughts on chalk paint

@scottsatterthwaite4073 2 жыл бұрын

That upper panel on the front of that bathroom cabinet comes off as do the ones on the front of the kitchen base (or have tip-outs). Remove them!! Don't paint them in or you will regret it.

@Fattony6666 2 жыл бұрын

I left them on and have no regrets

@scottsatterthwaite4073 2 жыл бұрын

@@Fattony6666 Congratulations

@SalehalOreef 2 жыл бұрын

Good work 👏

@DougZbikowski 3 ай бұрын

No sealant required after the paint?

@Guardducks 2 жыл бұрын

Behr paint and primer covers well. Had a friend who had her house painted twice by two different contractors and two years later the paint started fading and peeling. The difference was spray and roll

@MAGAMAN Жыл бұрын

You spray cabinets and roll walls. Not the other way around. Paint sprayed on walls has to be thinned down a lot to get it to spray and it just soak into the drywall and texturing. If you have ever tried to wipe off a mark from a sprayed wall you would know that the paint just rubs off and you rub a hole into the texture on the wall. Cabinets on the other hand are smooth and need to be sprayed to not have brush strokes or roller marks.

@imabearnow8395 3 ай бұрын

Noticed they didn't show a close-up of the finished product, how visible are the brush strokes when doing it this way?

@stownley2005 11 ай бұрын

No protective coat on latex paint?

@chrishoward6674 2 жыл бұрын

What would you suggest to use to fill the grain in the wood? Personally I can't stand to see grain on painted wood.

@weekendhomeprojects 2 жыл бұрын

You ever figure that out? I hadn't thought about that, but I imagine it would make for a nice smooth finish.

@meperson Жыл бұрын

I used Aquacoat but there are other brands. You could also try slurry sanding method. KZfaq has some good videos on pore filling for cabinets.

@meperson Жыл бұрын

@@weekendhomeprojects See my answer to the original question.

@peterochester2320 2 жыл бұрын

I used this paint with a 1/4" nap roller as instructed. Still left orange peel/roller texture as the paint does not self level. Noticed that you tipped the larger areas.

@michaelmcgee2026 2 жыл бұрын

Use a foam roller. Sherwin Williams carries flock and mohair rollers that will make it look like it was sprayed.

@peterochester2320 2 жыл бұрын

@@michaelmcgee2026 I've tried various foam covers and went back to the flock 1/4". May try mohair but suspect that the paint needs thinning as it skins over before leveling. Spraying is no different; thinning is required even if your sprayer is powerful enough to not need it.

@saca1 2 жыл бұрын

So there is a couple of reason you have orange pill ,1st you put it on to tick second the paint is too thick you need to thin it down or the pain is drying to fast and doesn’t have time to flow there is a lot of Self-leveling paint out there you can use. you can’t just use a regular wall paint ,you need to use a high end trim or cabinet paint. don’t try to do it in one or two coats we usually do 3-4 coats but very thin. By the way in this video they forgot to send the primer you always send the primer. And I guess the reason they did not spray it because homeowner does not have the money to buy a professional sprayer the one you can rent in Home Depot or Lowes are not meant to be spraying fine finish on furniture‘s those are meant to be do painting fence, houses etc.

@derewreck 2 жыл бұрын

That’s the faucet Kevin and Richard installed.

@kathymieczkowski4981 2 жыл бұрын

Ok just one more question!? Whybdo the velour paint rollers sometimes glide over a painted surface?

@Off-Grid 2 жыл бұрын

To much paint on the roller.

@kathymieczkowski4981 2 жыл бұрын

@@Off-Grid 1/4" nap the best for painting cabinets and any other project? I'm almost feeling hesitant in redoing my kitchen cabinets bc I want to do them right...this time. It's been about 4 to 5 yrs since they were painted. My husband chose the color that is on the cabinets now. We don't have a big kitchen. The walls are a salmon color; whereas the cabinets are a tad darker than a cream color, and with new flooring in our future, those current colors will make the kitchen look even smaller. I've rushed through many painting jobs, that is inside my own house, and I, like I mentioned, really want to do these cabinets slowly and to the point that I am satisfied. Help me to not feel hesitant and worried that I'll mess something up.

@MrTimtawsauce 2 жыл бұрын

use some aquacoat grain filler to get an even smoother finish

@kathymieczkowski4981 2 жыл бұрын

One more question...I notice that after rolling the paint on you use a paint brush. May I ask why? I've always just used the roller. I'm learning as a home owner to be a diy'selfer! Thank you!

@F0reverYoung 2 жыл бұрын

Get an airless sprayer if you want a professional looking finish.

@cpassehl 2 жыл бұрын

It’s a personal preference- brush strokes in the direction of the wood resembles wood grain, vs a roller that has a roller texture. Many people, myself included, prefer a light brush stroke. But yes, an airless sprayer is also a good route.

@kathymieczkowski4981 2 жыл бұрын

@@cpassehl I'm one who doesn't like brush strokes in past experience. A homeowner who is a diy'selfer have been for many yrs. Just want to do it right this time.

@kathymieczkowski4981 2 жыл бұрын

@@cpassehl My kitchen cabinets have been painted yrs ago. Just want a fresh look.

@edzachary8657 2 жыл бұрын

We call it laying it down, so you don't want the roller stubble look, if you have quality paint you roll it on and then you lay it down with a brush very easy, the paint should not show any brush marks, good quality paint is the key

@laurie6123 2 жыл бұрын

I painted my 50yr old cabinets after stripping and sanding but the only prob I had was the paint cracked at the hinge location. Behr latex..same primer

@derekleesmith76 2 жыл бұрын

Behr is the problem! It's a horrible paint! You need a better quality paint and primer. I have been painting for 25 years. Everytime I have used Behr it comes out horrible.

@weekendhomeprojects 2 жыл бұрын

@@derekleesmith76 Behr'ly covers...am I right?

@weekendhomeprojects 2 жыл бұрын

@@derekleesmith76 What is a good paint brand to use for this type of application?

@weekendhomeprojects 2 жыл бұрын

Did you end up repainting? What did you end up going with?

@rickfrazier1148 Жыл бұрын

What are they using for degreaser? What are they cleaning it with? Why do they leave out every important detail?

@beanzz5556 2 жыл бұрын

Needs oil primer. The wood tannin will bleed through the latex paint sooner or later no matter how many coats you put on it

@srharris88 2 жыл бұрын

couldn't agree more. I'm a painting contractor of 16 years. I always use oil based primer then acrylic topcoat. I like to sand before and after priming then a sprayed finish also.

@MotherClucker1 2 жыл бұрын

thats what I've been told. Oil. But cheap undocumented labor gets you cheap, low-quality work. Ask any Texan.

@666t 2 жыл бұрын

Bleed seal

@vhj5803 2 жыл бұрын

Latex primer works just as good dummy

@davetrial3972 2 жыл бұрын

The original laquer finish is holding back any possible tanning issue. Bonding latex is fine in this application. I would only brush here to avoid any roller texture in both the primer and finish. I'm sure a close up video would reveal some sloppyness as the paint started to set up before back brushing.

@chrisc.c52 Жыл бұрын

When it comes to kitchen cabinets, it's always better to use oil base primer.

@Pets-n-Treats 2 жыл бұрын

So if you don't have a tack cloth can you use a microfiber cloth?

@kathymieczkowski4981 2 жыл бұрын

Same process if cabinets have a color on them already? Lightly sanding so the primer will adhere? I so don't like the idea of taking out my hand sander, again, to sand down the kitchen cabinets. Btw...great video as always!

@rickfromthecape3135 2 жыл бұрын

Always a light sanding between coats

@kathymieczkowski4981 2 жыл бұрын

@@rickfromthecape3135 But not so much as to taking the whole coat of paint off correct?

@akoznasovajusername 2 жыл бұрын

@@kathymieczkowski4981 Sand only until you will have a dull look. Then you know the next coat will be able to stick on it and will not fall off as it would with the glossy look.

@kathymieczkowski4981 2 жыл бұрын

@@akoznasovajusername Ty for responding to my concern...if using my electric hand sander, what grit would be best to use on the current paint of the cabinets? I'm pretty sure it's a satin finish.

@MandoFettOG 2 жыл бұрын

@@kathymieczkowski4981 200 grit between coats works fine

@judywilliams3193 2 жыл бұрын

I`m wanting to have a fireplace put in with gas logs. Wish you guys would come put it in for me ! I live in a small town, dont know who to do the work for me.

@MountainwoodCottages 2 жыл бұрын

Im confused. Are you rolling and then immediately brushing over what you rolled or are you rolling the first coat and brushing the second coat? Also, should you caulk between the panels and the rails and stiles frame the center panel? Finally, can you use spray primer in a can to speed up things? Thank you!

@PeterSpexarth 2 жыл бұрын

I believe they rolled the primer on larger surfaces, and then grabbed a brush for areas they couldn't get to with a roller. Maybe they also did a final wipe with a brush for consistent texture?

@edzachary8657 2 жыл бұрын

So you roll the paint on just to get the material on the cabinets and then you back brush or we call it laying it down with a really good quality brush that way you don't have the texture of a roller, so you can use a brush and a roller to put it on and then you lay it down with the brush very lightly and if you're using quality paint you shouldn't see any brush marks

@Frank7748124 8 ай бұрын

Boat painters roll on the paint and then tip it off with a brush. The technique is known as "roll and tip". Look that up and you will find lots of help.

@wldmike223 2 жыл бұрын

Don’t use water based primer for cabinets! Use Zinsser BIN. It won’t come off with proper prep. Oil paint is best.

@Fattony6666 2 жыл бұрын

I've used water based for cabinets and it works great. Don't listen to "wildmike223" from the youtube comments for advice

@Painmaster212 2 жыл бұрын

@@Fattony6666 It may work fine but using an oil based or shellac based primer is much more durable then what any water based primer can give you. So for something you'll only want to do once, I'd go with the better working product for this particular job. An acrylic latex paint is fine on top of either primer but I'd suggest an enamel top coat, especially for something that will see daily use as it cures very hard and can stand up to abuse much better. Prep work is key to success for either product though.

@debbiepankau8950 Жыл бұрын

Can you paint the inside of the cabinets or not?

@airselectricalcontractors842 2 жыл бұрын

does air spraying look better than brush/roller or theres no difference ???

@marcomarcello3337 Жыл бұрын

If your doing a large project...like kitchen cabinets...I would do the cabinet shelves with brush and then hire someone to air spray the cabinet fronts...don't try to buy an air sprayer from the large chains...they clog and don't work well...hire someone! I learned the hard way! Make sure you prep the cabinet fronts properly first...I used liquid sandpaper and a stiff brush...worked great.

@mhoefler914 2 жыл бұрын

A question I have not found the answer to: Several professional painters (for outside) said primer should sit for 24 hours before you paint so it will 'cure'. The paint can says dry in an hour or so. I have some paint failing and not sure if it is bad paint or that I painted too soon after primer. (I would never use the primer + paint.) This Old House or even other painting videos have never addressed in any video the question of how long to wait .

@michaelmcgee2026 2 жыл бұрын

Always follow manufacturers instructions which will vary per primer

@saca1 2 жыл бұрын

So the previous answer is right follow manufacture recommendation. My experns is and I’ve been doing a lot kitchen cabinets is Different . I used multiple primers in my past oil primer, latex primer. I never had to wait more than a couple hours after after I applied it to start sending it down. if you put it on to thick it’s gonna take forever to dry . the primer usually goes on very thin and does not have to cover solid. You can use oil primer what you can send very easily and dryes very quickly there is also bonding primer if you have an item you want to paint but you’re not sure if they use latex or oil or polymer or polyurethane paint you can always just put a bonding primer on it very thin and then you can put anything on top of it even on the oil primer you can use a latex finish. Drying time : You always have to thinking about the condition where you priming it if it’s a lot of humidity it’s gonna take forever to dry no matter if it’s water or oil base. After you prime something and you able to touch it without getting paint on your hand you can put it outside on the sun and let it bake for 30 minutes or an hour it’s kind of like the way they do it in a Commercial settings where they put it in the oven.

@mhoefler914 2 жыл бұрын

Thanks for the reply and that seems to cover inside painting. Several outside painters told me to wait 24 hours after priming for it to cure (oil and latex primer). Just because it is dry to the touch they claim it still needs time. Have any of your pro-painters heard of that?

@twsd 2 жыл бұрын

What you want to look for is the recoat time. It could say dry to the touch in two or four hours but the recoat time could be 12 or 16 hours. FYI it takes paints and primers weeks to cure.

@luisc1748 2 жыл бұрын

It seems to me, and I may be mistaken here, but, it appears that the top coat was a Behr Premium Cabinet & Trim Enamel Interior paint. Am I wrong?

@davidherd3739 2 жыл бұрын

You’re correct

@ralphhooker6019 2 жыл бұрын

I think back to the days of Bob Vila. The bad old days. Today TOH is strong, vibrant and relevant. Keep on keeping on. Thanks.

@robertkattner1997 Ай бұрын

Make sure to use Floetrol in your paint, then you won't have any brush marks.

@MrAtilano306 2 жыл бұрын

I had my cabinets painted professionally and the paint seems to scratch pretty easily. Is this normal or did the “pros” skip a step?

@michaelmcgee2026 2 жыл бұрын

Shouldn't scratch easily but that could be many different reasons. Didn't sand. Didn't use the right type of primer. Didn't use the right type of paint.

@edzachary8657 2 жыл бұрын

It's a really tough job to get right, cabinets take a beating people's fingernails constantly up against them when you go to reach for a knob or a handle if you don't take your time and you try to skip the sanding step you're going to have problems, it's a lot of money to have somebody come in and do it correctly obviously depending on how many cabinets you have

@weekendhomeprojects 2 жыл бұрын

Did you figure out what they did wrong? Get it fixed or repainted?

@1977logitech 2 жыл бұрын

Don't forget to fill the pores on all those oak cabinets unless you want the texture to telegraph through the paint.

@danb.709 2 жыл бұрын

I like that look, texture is very important on something like a cabinet. I'd prefer the natural wood grain to roller and brush strokes. Also not sure what you'd use to fill it, except a high build primer and sanding, I'd rather use a high bond primer, I suppose you could do both, one after the other, but that sounds like a lot of work.

@thezfunk 2 жыл бұрын

@@danb.709 They make grain filler that you spread on the wood before painting or finishing. I just learned about it.

@vhj5803 2 жыл бұрын

No need for all that

@Off-Grid 2 жыл бұрын

The cabinet paint will cover.

@danb.709 2 жыл бұрын

@@Off-Grid it's not about it covering, it's about it getting scraped off and dinged up during normal use. Also I like the wood grain texture, which a standard one coat of primer, and one or two coats of paint will not cover up, apparently others may want to fill the grain, but I wouldn't trust a normal wood filler over urethane.

@nicklk 2 жыл бұрын

Anyone know what brand of primer they used?

@marty9660 2 жыл бұрын

HOMERIGHT FINISH MAX SPRAYER 24mm Yellow Frogtape

@allenkim6665 2 жыл бұрын

use oil primer then water based finish paint

@HaakonAnderson 2 ай бұрын

Just did my moms bathroom, hater's gonna hate... 😅😂

@MrLESiPhone 2 жыл бұрын

Why not spray paint the cabinets. It would seem that you would end up with a smoother finish?

@TheRealNosferatu 2 жыл бұрын

Spraying is definitely better! But for those without a sprayer, brushing and rolling a urethane enamel (ben moore advance, sherwin emerald urethane) Gives a great finish still. Not the same but still exceptional if done well

@marypoirotjones5563 Жыл бұрын

A lot of people suggest spray painting, but I haven't seen many people showing how to do this in the home. It seems to me if one is not a professional painter, the investment into costs to do this would be daunting. Unless you are going to be spray painting a lot, you might as well buy new cabinets! Also, spray painting would require more than tape and a little newspaper to avoid over-spray depositing on the rest of the kitchen. Someone I know, having more money than most homeowners, hired someone to spray paint their cabinets. The painter took doors and drawer faces to a shop that was dedicated to spray painting, where the parts could be hung for painting. They brush painted the frames and sides in place in the home. For folks like me having a small kitchen and needing to do this job maybe once every 7-10 years, spray painting is just overkill.

@rafaelsays175 2 жыл бұрын

Mauro is the man when it comes to paint

@lad4944 2 жыл бұрын

As a painter of 42 years, and watching this gentleman on TOH for awhile. I can tell you, Mauro still has a lot of learning to do. That will come with time.

@Voelkswagon 2 жыл бұрын

Shellac primer is best and you should do a spray finish if you can. You'll be much happier with the results. If they were to do an up close look at the finish product all you would see is brush marks and orange peel, no thanks..

@billwilson6670 2 жыл бұрын

What degreaser did you use?

@suzanacarey 2 жыл бұрын

I find the best degreaser to be Krud Kutter. It's awesome

@billwilson6670 2 жыл бұрын

@@suzanacarey Thanks. I've seen it in stores and will give it a try.

@VinnyGjokaj 2 жыл бұрын

You can use standard dish soap, go dish soap wash it nicely, dry, then do a cleaning with a rag and acetone and it’ll be really ready

@walterm2871 2 жыл бұрын

wont water based primer and paint peel? i was taught to use oil based on wood surfaces to adhere best not water based. i once dealt with water based on wood and it peeled so easy

@khl619 2 жыл бұрын

totally fine to use water based on wood. tech had come a long way.

@Fattony6666 2 жыл бұрын

no it won't peel

@veronicalake4093 2 жыл бұрын

Whoa this is lovely. I have a million cabinets can u guys come do it for me 🙂

@tomwatson1978 2 жыл бұрын

I'm confused...In the notes there is a link to INSL-X Cabinet Coat Enamel paint which is really good stuff, yet at 4:00 he breaks out the Behr paint. Ugg.. what's up with that?

@guillermohiramduartegomez8561 2 жыл бұрын

Water base paint for wood?

@ryane6719 2 жыл бұрын

Raise the grain, hard to sand, poor adhesion… what’s not to love lol

@donaldquick9520 2 жыл бұрын

They should have mentioned what type of cleaner to use to degrease the wood.

@Minibike817 2 жыл бұрын

TSP Heavy Duty Cleaner ?

@J-Irv 2 жыл бұрын

Krud kutter

@rickfromthecape3135 2 жыл бұрын

There's a ton of details they should have mentioned.

@srharris88 2 жыл бұрын

Its hard to find any one cleaner that will get cabinets all the way clean. There are sometimes a variety of different oils and stains on them. I have found denatured alcohol works pretty well though.

@ryane6719 2 жыл бұрын

@@srharris88 tsp