Same

I worry for your intelligence if you needed a tutorial on how to use a screwdriver

@@theburger_king if you say so, but this helped me know where to put the 3 pin cable on the motherboard

@@Broksium don’t you have a manual

Same

How did you put it in? Like did you only plug it into three of the prongs and leave one out? I just don’t want to break anything. Could you just explain what you did?

@@lukethedoge4842any solution bro ?

@@lukethedoge4842yes just plug into 3 of them, the same as he does in the video bro. The 2 plastic grooves slot in at the bottom of the 4 prongs

@@GazPlaysChesssry the vid was just really blurry and I didn’t wanna get it wrong, appreciate the help!

@@lukethedoge4842 let me know if you manage to get it in bro? It should slot in easy and the plastic grooves should fit nicely. Don’t force it

So did he do it correctly or nah

Not correct

well if you have a 3 pin on the motherboard u can still connect the 4 pin but its impossible to do any pwm controls

@@skitzersI have a 3 pin fan and 4 pin mother board and all of my other case fans matched the mother bored with a 4 pin connector so idk what to do

I totally didn’t think of that. I’ll make a video covering it!

what's that?

which is more important then anything 😅

@@pablolee2252 intake and exhaust. ill explain it to u. the front (aka the face/the nice looking part) of the fan sucks air in, the back blows air like a normal fan. the exhaust fan should have the front facing the right side of the case, and the intake fan should have the BACK of the fan facing the LEFT side of the case

i think that’s the point, it’s on the back of the system

Dont use ARGB or DRGB(meant only for 3 pins)- it is 5v Use traditional RGB which has 4 pins on your MB RGB port which reads 12v(Reads as GRB or something like that). Note: If the cable length is smaller you may need to buy extension cable which costs more for a single fan.

dude i built my first pc on my own to help or instructions it took me 2 hours to figure out everything now i can build for in 30 minutes but installing the fan and plugging it in was the easiest and quickest thing to its so obviously theirs only one connector it goes into unless you running some shit from 2012

these tutorials should specify that you should plug the case fan into the SYS_FAN header. people could confuse it with the CPU_FAN header but only if they are stupid enough to not know what a cpu is and they just call it a processor/microprocessor

use ARGB or DRGB(meant only for 3 pins)- it is 5v

yes basically that's how i installed mine you make the threads urself by screwing

If you have for example a 4 pin connector, there should just be a slot for it on the motherboard and you shouldn’t have to worry about

you can use a fan splitter or a hub

Will RGB it's just four-pin and goes in the same slit

You can connect your fans to SYS_FAN, SYS_FAN1, SYS FAN2 etc on your motherboard, normally its 4-pin connector, but if the fans have 3-pin cable you can still plug them in just leave the fourth pin blank.

Yes

Yes, you need to, to manage the cable

bro what are you talking about

@@taylorebenguard6998 why are you here? hes talking about the arrows which are on the side of the fan which indicate which direction the air will get sucked in. you can also use the arrows to figure out the exhaust. or an easier way to determine it is that the front of the fan will always suck the air in and the back will blow the air out. the front is the nice looking side and the back side is the ugly looking side.

@@dynahzm this video oddly enough got suggested to me scrolling through shorts

No idea😂

Even better use a Pneumatic drill gun

no not really

@@richarddixon146 drills are too strong fr.

I don't actually know the name of them. I just call them fan screws. They're the ones with the large thread.

Maybe your fan cheap or you don't put fan correctly

@@Manusia.satu1 no it isn’t cheap

you can try looking on the side of the fan maybe there will be an air indicator indicating where the direction of the airflow is

@@skitzers or u can just blindly look at the fan and determine the direction of the airflow. "faces suck" the face/front of the fan will always suck in the air.

It’s an old NZXT S340. It was replaced by the H500/510

i can’t believe so many of you keep saying this and its the simplest thing to figure out

@@taylorebenguard6998 most of these people are amateurs. people arent all smart as u

not all, some fans have different measurements like 40, 60, 120, 140mm but your case might not support them. check the size of the fan and make sure your pc case fits the size.

nah you need to fans just leave the glass panel off 👍

It's unironically my best screwdriver😂

i mean thats kind of obvious having it blowing the same direction as your front fans so it blows air through the case

@@taylorebenguard6998 obvious? thats not obvious. i know the orientation of the fan is but its not obvious first time that i learned it

@@dynahzm well when you plug it in just put your hand in front of the fan to see which way it’s blowing

@@taylorebenguard6998 i personally wouldn't get too close to a running pc fan because i don't want my finger ending up discombobulated

​@@taylorebenguard6998yeah and if it's wrong you get to uninstall and do it over again! Maybe it'd be helpful if that info was covered in the friggin "how to install a pc fan" video??? How many embarrassingly dumb comments did you post under this clip?! 🤡

Yeah you can just make sure its the right pins (3 pin can connect to 4 pin)

@@HH-co9yo get new fans

​@@dreamsofthefuture2890You've likely figured this out by now, but here's a tip for those searching: Look in the manual for motherboard layout and a diagram of the 4 pin headers. The PWN pin is on the end opposite of the ground pin. Plug in the 3 pin leaving the PWM pin exposed. Fair winds and following seas to all.

It’s a Fractal Design 120mm. Not too sure on the specific model

same way you did the back ones

Care to share anything constructive?

@@ProYamYamPC Fan orientation is a massive thing you forgot

💀

You speaking about maturity when you comment this🤣🤣 Is everything ok?

It doesn’t matter just make sure its a fan header