How To Install A Clutch Lockout On Banshee

Рет қаралды 12,522

4 жыл бұрын

How To Install A Clutch Lockout On Banshee
Subscribe 👉 bit.ly/RedoBansheeSubscribe
REDO-PARTS SHOP - redo-parts.com/shop/
If you find this video helpful, make sure to drop a like & leave a comment down below!
➖➖➖➖➖➖➖➖➖
How To Remove And Inspect Banshee Clutch Cover And Clutch:
• • How To Remove And Insp...
➖➖➖➖➖➖➖➖➖
Subscribe 👉 bit.ly/RedoBansheeSubscribe
Extra keywords (don't pay attention):
four wheeler,4 wheeler,restoration,restore,custom,quad,dirt bike,dirtbike,banshee,banshee 350,yfz350,yamaha banshee,how to change a clutch,how to change a banshee clutch,banshee clutch change,yamaha banshee clutch,banshee clutch mod,aftermarket banshee clutch,yamaha banshee build,banshee bad clutch

Пікірлер: 16

@davidreed4320 3 жыл бұрын

Great video

@RedoBansheeParts 2 жыл бұрын

Glad you enjoyed it

@hectorramos8039 3 жыл бұрын

hello friend I have a problem in my 2006 yamaha banshee when I put the first one it turns off that could be?

@conniestevenson226 2 жыл бұрын

@Mske keeps clutch from slipping under power.the faster it spins the harder it makes the clutch bite

@hectorramos8039 3 жыл бұрын

The pancake it's necessarie change ?

@kodyhowe2729 2 жыл бұрын

What about using feeler gouges to set the correct and even gap between the back of the lock up and pressure plate?

@RedoBansheeParts 2 жыл бұрын

Unnecessary tighten them in a star pattern evenly and you won’t need a feeler

@mr.rem2609 2 жыл бұрын

Im looking at doing this to my banshee. I guess you can use your stock cover with this?

@RedoBansheeParts 2 жыл бұрын

You would need a lock out specific cover for most.

@jayshafer16 2 жыл бұрын

how do you adjust the pancake bearing when using a lockup? Do You have to install the springs and the screws first to tighten it down? If so, how do u get to the lock nut for the pancake bearing to adjust it with the lockup in the way???

@RedoBansheeParts 2 жыл бұрын

You can use a crows foot if you are having a hard time with reaching behind the jam nut

@ramiropenuelasmonje4059 4 жыл бұрын

Para que le sirve eso amigó?

@Jasonsito 4 жыл бұрын

Ramiro Peñuelas monje Un clutch más fuerte Para los banshees alterados

@calastrcas 3 жыл бұрын

Ramiro puñelas eso se usa cuando alteras un motor de banshe 4mm o más para que el clutch se apriete más y aga mas presión y no se patine el clutch ala ora de arrancar

@phillyboydicez8244 2 жыл бұрын

You never finished explaining how to adjust the disengagment mechanism

@RedoBansheeParts 2 жыл бұрын

kzfaq.info/get/bejne/qciia8mLuauqfn0.html is a video on adjusting the stock. Its the same but you need an extra wrench to hold the adjuster from spinning while you loosen and tighten the jam nut.