No video
How to Install a Lathe DRO Kit. Manual Lathe 2 Axis Digital Read Out.
Рет қаралды 116,114
4 жыл бұрынIn this video I will show you how I installed a new 2 Axis DRO kit onto my Harrison VS330TR manual lathe. How to install a lathe DRO kit on a lathe is relatively simple. However, there are some intricacies. The Job of the Digital Readout (DRO) is to tell the lathe operator the relative or absolute tool position with respect to either the part or the machine. Using the DRO is much faster than using the hand dials as you don't have to worry about backlash. To install the DRO I first mounted the display; the DRO itself. Then the linier scales. The scales are the parts that measure the positions. There is one for each axis. In the case of this machine the Z axis and the X axis. The lathe axis system is defined using the right hand rule. The X axis is positive towards the lathe operator across the machine. The Z axis is positive away from the chuck down the length of the machine. An easy way to remember it is that if you are moving towards the chuck you are moving in a negative direction.
If you like the videos I make then please consider sharing them with your friends. There is a share button just below the video viewer. It's got loads of options for easy ways to share a link. This REALLY helps the channel to grow and enables me to bring you more videos.
For more information and behind the scenes content be sure to check out my socials
Facebook: handmadeextreme
Instagram: handmade_extreme
If you would like to make a contribution to the channel then I also have a Patreon page.
www.patreon.com/handmadeextreme
Cheers,
Rob
- Handmade Extreme -
Disclaimer: This video is meant for educational and entertainment purposes only. It is in no way meant to be a set of instructions and therefore no attempt should be made by any party to recreate what has been seen or heard in this video. Any attempt to do so is done completely at your own risk.
@floydraser4603 8 ай бұрын
I just found this (30.11.23) as I'm planning on fitting one to my Warco 280. Well done for fessing up to re-welding the bracket. And I thought it was only me who does that! 😄
@stxrynn 2 жыл бұрын
I think I have that very kit. It came with a used machine I recently purchased. Nice video and, since no manual came with the kit, I have what I need to install this. Thank you! Very nicely illustrated and narrated as well.
@qcnck2776 4 жыл бұрын
Thanks for posting your install. I had mine pre-installed and getting to the back for the Z axis would have required a lot of messing about. Having said that, I'm sure you will really like having the DRO. I can't imagine doing without mine.
@Handmadeextreme 4 жыл бұрын
Thanks, glad you enjoyed it. They are so handy aren't they. Iv'e used them on various machines over the years but never had one on my home shop lathe until now. Got one on the Bridgeport as well which is super handy. Thanks for the support. 👍
@geoffwilkinson5183 3 жыл бұрын
Great video. I happen to have a Harrison M300 and bought a DRO almost the same as that, so your video helped me enormously. I didn't need to turn the cross slide bracket upside down, and didn't quite understand why you needed to. I still need to install a tailstock stop and I need to figure out how to run the cabling so its out of the way. I was a bit concerned about swarf getting into the back of the Z axis scale, so mounted that on an aluminium plate first. Thanks for posting this!
@stuarth43 3 жыл бұрын
noice, you made me smile with the word (little} which you use many times, buying a bomatec tomorrow for my cazenueve 575x2000, did not realize that the scale moved on the cross slide. so learned something
@Handmadeextreme 3 жыл бұрын
Awesome, hope it all works out with your machine. Thanks for watching.
@stuarth43 3 жыл бұрын
@@Handmadeextreme thank you everything is double difficult since I had a stroke 4 years ago but I plug on I was a yacht building take a look at my channel if you have the time
@williamjohonson5459 2 жыл бұрын
Thanks very helpful , I'll be doing the same job myself soon , there are some small sockets available that take taps so you can use a1/4 or 3/8 drive ratchet makes life a lot easier in those confined spaces .
@crisislord00 4 жыл бұрын
I always wondered how a dro is installed! Great video!!
@Handmadeextreme 4 жыл бұрын
Thanks. I'm glad you found it useful. 👍
@DatBrummie 4 жыл бұрын
Nice video, but based on the DROs I've seen, the 4 threaded holes on the bracket were actually for grub screws, that can be used to securely hold the bracket flat on an unflat surface, acting as spacers where they need to. I think the holes for actually mounting it were the ones on either side, between the threaded holes? It doesn't make much difference in your case as you mounted it on a flat surface anyway but all of the DROs I've seen have been mounted with grub screws to hold them straight even if they're on a curved surface.
@Handmadeextreme 4 жыл бұрын
Interesting, great comment. I did wonder if the larger holes in the centre were for mounting it but the kit didn't come with any hardware that diameter. What you say does make perfect sense though. Iv'e learnt something new here today. Thanks very much and i'm glad you enjoyed the video.
@TheAussiePirate 4 жыл бұрын
You made that look very easy. I’m always nervous doing those kind of things.
@Handmadeextreme 4 жыл бұрын
Yeah iv'e never enjoyed drilling holes in machines it's always very nerve wracking. Glad you enjoyed it, thanks for the support.
@jagboy69 4 жыл бұрын
Just use quality taps and take your time. It's not a hard job at all.
@harveyedwards3725 7 ай бұрын
Nice simple video thank you for taking the time to make it
@TigerCarpenter 2 жыл бұрын
very thoroughly explained. I'll do it on my lathe soon too
@compassprecision 4 жыл бұрын
Another good video. Really liked the close up shots of your demonstration. Thanks for sharing!
@Handmadeextreme 4 жыл бұрын
Thanks, glad you enjoyed it.
@PastenTube 3 жыл бұрын
Great video, thanks. Still thinking about buying a DRO for my Colchester Student, but having to drill into it somehow scares me.
@lewevans2413 Жыл бұрын
Thanks for the video, it was very helpful.
@ottoolsen9676 2 жыл бұрын
installing the dro screen is a personal thing ofcorse, but usaly it is fittet to the table on a stand, on this lathe mounting it on the gearbox is fine, but on bigger lathes you want it where you are doing the job, and the table follows to where the work is done. anyway nice video.
@walterkreitmeier5079 2 жыл бұрын
Well done, in a fine maner. Many thanks for this Video.
@ron1en1 6 ай бұрын
Do you have a link for the product?
@ita-1245 2 жыл бұрын
Best lathe DRO installation video. Cheers.
@georgeyork8975 3 жыл бұрын
Nice precise video on installing DRO. I just bought mine and this got me thinking about how the X axis mounting technique would be applied to my lathe. I have a Clausing 5914 which has a similar cross slide configuration, But I noticed on mine that there is very little real estate on the slide on top to drill into and compound rotation is very tight with maybe 1/8 inch clearance. So i have no other choice but to attach from the side of the cross slide. I am very concerned with where to drill as not to disturb or weaken the gib areas etc... Thanks for the video though it has allowed me to glean more ideas of how to mount the unit.
@Handmadeextreme 3 жыл бұрын
Glad it was helpful. You may find it is easier to attach to the front of the cross slide, just something to consider. I also was concerted about the gibs, the angle bracket seems to have worked well at overcoming this problem. Good luck with your own machine and thanks for the support.
@flaviator9957 2 жыл бұрын
Had the same concern about drilling the holes. Solved it by taking two suitable plates of aluminum, drilled the mounting holes for the scales in there and glued these to the machine with a Locktite high strength glue. Thoroughly removed any paint and dirt before and degreased the glue areas properly as well.
@kgee2111 3 жыл бұрын
Brave man using a power drill to tap with!
@Handmadeextreme 3 жыл бұрын
It's always a bit sketchy.
@union310 3 жыл бұрын
Common practice in industry
@stefansolcan9955 2 жыл бұрын
Please tell me how to set the computer for Y axis. Because when the DRO show me 1mm, actually the cutter go 0.5mm.
@dreamsteam8272 2 жыл бұрын
08:15 "slow is precise..... precise is fast!"
@hopefuldave 4 жыл бұрын
Good demo - you'll definitely want a stop / buffer to prevent the scale / reader bashing into the tailstock! I've done quite a few DRO installs on Other People's lathes and mills, found the supplied brackets a bit of a faff so made up mounting pads with cone-point grubscrews at the corners to jack them into alignment as a lot of lathe castings aren't precisely square/parallel (particularly the Chinese ones with 1/4" of filler...) A question for you - I'll have a bit less than 1/8" total clearance if I feed a standard-size scale above the taper attachment and below the cross-slide overhang (the only place it'll fit without the taper attachment getting in the way of the Z-axis bracketry), was thinking the slim scales would be better, - it looks like you used them, were they a lot more expensive, and where from? I can probably justify 1um scales on the Holbrook, worth the extra $20/scale!
@Handmadeextreme 4 жыл бұрын
Thanks, i'm glad you enjoyed it. I used a standard scale on Z and a slim scale on X. It's just what came with the kit to be honest. The slim scales are definitely a bit smaller though which would be good if your tight on clearance. Regarding costs it's probably best to have a chat with your suppliers they might be able to do you a bit of a deal if you are buying a full kit. Mine were only 5um scales but that's all I needed. Thanks for watching.
@insat-xx9cm 2 ай бұрын
Buen trabajo, gracias por compartir tus conocimientos Estoy automatizando una fresadora , que se podría implantar en un torno, en mi canal estoy subiendo la información
@simonefanfarillo3185 3 жыл бұрын
Hi,I'd like to know of This kind of Digital dro can read the "x" axis as a diameter or normal Linear positions?thanks
@Handmadeextreme 3 жыл бұрын
It can do both.
@alangliniak9514 3 жыл бұрын
Great video I am planning on adding an ebay dro to my harrison m300 fairly soon. Keep us posted as to how it holds up.
@Handmadeextreme 3 жыл бұрын
Will do, Haven't used it that much yet to be honest. But so far so good.
@tonycstech 2 жыл бұрын
I like this DRO system Do you have a link where yo bought it or a model name or what ever ?
@greatdane3343 Жыл бұрын
Nice one mate. You made that look pretty easy!
@premier_attachments4971 Жыл бұрын
Hi Great video, really clear and easy to follow. Hows the dro kit holding up 2 years on please? Just about to get the same kit . Thanks.
@robinmidgett3347 Жыл бұрын
Well done installation and demonstration video!
@steveclark.. 4 жыл бұрын
Have you got a link to the seller of this DRO? Was it posted in the UK or from China??
@Handmadeextreme 4 жыл бұрын
www.ebay.co.uk/usr/valuedro?_trksid=p2047675.l2559 Yes UK, they are in stocked just outside Derby
@ronnieg6358 3 жыл бұрын
As a last resort read the instructions!
@24Tunnel Жыл бұрын
Good job where to buy and what model
@tamurhaq 2 жыл бұрын
Lmao on welding the bracket back. Funny.
@alanstapleton3818 3 жыл бұрын
did you check the calibration for accuracy ?
@paweisyn7446 3 жыл бұрын
Good demo :)
@robertfournier947 3 жыл бұрын
Good job, straight to the point.
@Handmadeextreme 3 жыл бұрын
Thanks. Glad you enjoyed it.
@bigbothoee8617 8 ай бұрын
Wow that was easier than I thaught lol guess what I just ordered
@josephmufdi4564 2 жыл бұрын
Outstanding job man!
@colinstu 4 жыл бұрын
wait, why did you have to cut the bracket? xD
@Handmadeextreme 4 жыл бұрын
Haha, Hi Colin. Let's just skim over that shall we 😂. Let's just say it's a good job I have the AC TIG set on hand... Thanks again for watching.
@carlwilson1772 4 жыл бұрын
A very nice job. I also have some right angled collet windy drills from my aircraft days. I used mine on my dro fit too. It looks like a good kit. Can you put a link to it on ebay please?
@Handmadeextreme 4 жыл бұрын
Thanks Carl glad you enjoyed it. The right angle drills are so good I used it a lot when I built Pippa as well. This is the kit I bought, I have no connection with the company. It went together quite easy. I'd say good for the price point. Can't comment on longevity as i'v only just put it in. Thanks again for the support. www.ebay.co.uk/itm/2-axis-digital-readout-DRO-for-lathe-complete-kit-UK-stocking/183150601752?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D20160908105057%26meid%3D9a9d81bb4ff04e8e898ee1a6c15d2066%26pid%3D100675%26rk%3D5%26rkt%3D15%26mehot%3Dpp%26sd%3D224029740604%26itm%3D183150601752%26pmt%3D0%26noa%3D1%26pg%3D2380057&_trksid=p2380057.c100675.m4236&_trkparms=pageci%3A830dc46f-e4c1-11ea-9686-ee8f00151d46%7Cparentrq%3A1826e64d1740a69d345c4c0ffffffe90%7Ciid%3A1
@carlwilson1772 4 жыл бұрын
@@Handmadeextreme Thanks for that. I am looking to get the three axis version eventually, for my mill resto. I put a DRO on my Harrison lathe that I got from Ems International. I'm seriously thinking about changing the carriage scale from magnetic to glass, as the magnetic one is really jittery at times. Just throwing this out there, but something I'd find interesting would be some tests on your lathe, ie how parallel does it turn without tail support, is the tailstock alignment good, does it turn a cylindrical cut, that sort of thing. A lot of us out there have "old iron", me included (if you can class a 1984 Harrison M250 as old - and I guess you can) so I think it would be instructive to find out about these things.
@Handmadeextreme 4 жыл бұрын
No problem. I'll have a think about what you suggested I've been playing with that sort of thing recently (lathe levelling and the like) as I had to turn some long shafts recently. I've been thinking about making a new plinth for my lathe so that will all need doing again after that.We will have to see how things play out. Thanks for the idea, and the continued support. Good luck with the mill resto. 👍👍
@carlwilson1772 4 жыл бұрын
@@Handmadeextreme Thanks for taking the time out to reply. I've been spending a bit of time lately fettling my lathe and I just wondered how other people's are.
@Handmadeextreme 4 жыл бұрын
No problem, thanks for the support. 👍
@anthonyfox5337 3 жыл бұрын
Nice work mate.
@MarkATrombley 4 жыл бұрын
For those of us not in the U.K. what is a combi drill?
@Handmadeextreme 4 жыл бұрын
It's a battery powered cordless drill. Not sure what they are known as around the world but it's the one that has the 3 modes of operation. Normal drill, percussion drill for masonry and an adjustable clutch so it can be used as a screwdriver. Hope that helps. Thanks for watching.
@MarkATrombley 4 жыл бұрын
@@Handmadeextreme In the U.S. that would be a drill/driver or a hammer drill. Thanks for the answer.
@Handmadeextreme 4 жыл бұрын
Awesome, thanks for that. 👍
@4639desoto 3 жыл бұрын
Why buy a DRO direct from China ? There are many others that are much better
Дима Масленников
Рет қаралды 7 МЛН
TITANS of CNC MACHINING
Рет қаралды 324 М.