How to install a rubber recoil pad: Part 2

No video

How to install a rubber recoil pad: Part 2

Рет қаралды 27,846

4 жыл бұрын

Part 2 We avoid disaster on this Browning Citori by getting the pad blueprint online from Lyman Products and Pachmayr®, and then pre intall, mark, and rough grind the pad. At the end we do the final hand fitting, finish, and reveal.
SixRounds Studio
Wood Chips & Black Steel

Пікірлер: 40

@tonywestbrook6436 4 жыл бұрын

The average joe thinks it's as simple as changing out a light bulb for another until seeing your video. Lots of time consuming and precision work goes into changing or adding a recoil pad. Great tutorial sir!! Well illustrated!!

@SixRoundsStudio 4 жыл бұрын

Thank you ! It does take a lot of patients. This is one of those jobs that you go slow to go fast.

@texaswader 3 жыл бұрын

Perfection! What the work of a master gunsmith looks like; the fit is perfect, no ridges and no screw holes visible. Man I enjoy your channel.

@SixRoundsStudio 3 жыл бұрын

Geez....thank you.

@LAUptegrove Жыл бұрын

I have a Citori Lightning that I'm wanting to perform this task on. In my late 60's, I only hope my hands are steady enough to do it correctly and neatly. Thanks for all the tips.

@SixRoundsStudio Жыл бұрын

Thanks for watching...really appreciate it! If you havent...please watch part 1. They are a set

@Kevins-Philippine-Retirement Жыл бұрын

Very nice work. I spent many years as a Level II Gunsmith, doing just about every job imaginable. But pads were one of them. It can be tricky work such as avoiding the steel plate and grinding to continue the lines of the stock. Many would think it's a quick and dirty job, but we both know it requires attention to many details.

@SixRoundsStudio Жыл бұрын

Yes sir. Takes patience and a willingness to do it right. Thank you for the comment.

@daviddixon9598 Жыл бұрын

Great job! Better than some gunsmith jobs I've seen. My son has a Ruger number 1 that was hacked by someone. I've done a few but this time I plan to buy a fixture.

@SixRoundsStudio Жыл бұрын

Thanks David! Been doing this for a long time.

@SuperKwame1 3 жыл бұрын

Excellent, Job. Great video/ Music.

@SixRoundsStudio 3 жыл бұрын

Thank you for watching and commenting.

@gadgethunter5732 3 жыл бұрын

A properly fitted recoil pad like this looks worlds better than the current Browning mushy rounded at top and bottom inflex pad they put on everything.

@SixRoundsStudio 3 жыл бұрын

Pachmayr® makes a great pad

@codyb.7690 4 жыл бұрын

Great Job I loved your video

@SixRoundsStudio 4 жыл бұрын

Thank you Cody...fun to make

@TheSchuey1 7 ай бұрын

Great stuff. So cool to see this done without a fixture. Is there something specific you use for a sealer. Any suggestions? Thanks for posting.

@SixRoundsStudio 7 ай бұрын

Thanks for the comment and question. I do seal. I use a thinned down tung oil for sealing the end grain.

@TrojanSalesmen1 Жыл бұрын

I'm going to Gunsmithing school at the moment and I really wish they would allow us to use a belt sander because hand sanding the recoil pad down takes so long.

@SixRoundsStudio Жыл бұрын

Well...learning handwork is an essential first step to understanding material and technique. It is important to understand time and feel. I may start with a machine...but if you watch...I always finish by hand. It also teaches patients...that is so critical to craft. Thanks for watching and commenting Trojan!

@williambrown2453 7 ай бұрын

Great job!

@SixRoundsStudio 7 ай бұрын

Thank you William (Bill?)

@beefcakes27 Жыл бұрын

Nice job...

@SixRoundsStudio Жыл бұрын

Thank you Sean

@Brynny211 Жыл бұрын

Man are you located in New York I need this done ☑️

@SixRoundsStudio Жыл бұрын

No NH

@imarooster3548 3 жыл бұрын

Excellent

@SixRoundsStudio 3 жыл бұрын

Thank you so much 😀

@philippbecker5392 Жыл бұрын

Top 👍

@SixRoundsStudio Жыл бұрын

Thank you!

@jaybilly12345 2 жыл бұрын

Was that a big scratch visible at 6:42?

@SixRoundsStudio 2 жыл бұрын

Yep...This is a working shotgun and not a closet queen. The guy that owns it is a very good skeet shooter.

@hugosanchezjuarez4326 3 жыл бұрын

HOLA ALGUIEN SABE DE QUIEN PUEDE HACER UNA CULATA PARA ESCOPETA?

@kenstirling5348 2 жыл бұрын

Putting a recoil pad on is easy. Putting a recoil pad on and having it look like it’s supposed to be there and fit without any misalignment is a difficult task.

@SixRoundsStudio 2 жыл бұрын

All requires attention to details and patience.

@kenstirling5348 2 жыл бұрын

@@SixRoundsStudio and some tools that are worth their weight in gold if you do a lot of projects like this

@SixRoundsStudio 2 жыл бұрын

@@kenstirling5348 You a gunsmith or woodworker?

@kenstirling5348 2 жыл бұрын

@@SixRoundsStudio I’m the dude that messes shit up in my garage on Saturdays and then has to pay a gunsmith or a woodworker lol

@SixRoundsStudio 2 жыл бұрын

@@kenstirling5348 Well....I'm the guy who has a lot of respect for the guy who tries to do "shit" in his garage! I think we have lost so much of that interest in exploring ideas and skills. Thumbs up for you 👍