Thanks for the explanation on increasing tension as well as decreasing. I watched four videos and none covered as well as yours.
@bleurose2102Ай бұрын
Good content a different channel didn’t have a hinge with this kind of mechanic. I appreciate the info
@GlennHuang9 ай бұрын
Thank you for the time you took to make this. It really helped!
@ElGrantRikun1 Жыл бұрын
If the pin gets to deep in the hole just use a magnet to pull it out of it (that's what i did and it works).
@pablogutierrez10098 ай бұрын
Thanks a lot for a nicely done informational video.
@Leopold5075 ай бұрын
Good explanation body Well done and understood
@ajaibsingh21282 жыл бұрын
Very good explanation.
@Trainman04013 ай бұрын
Very helpful thank you!
@sportsnetusa1 Жыл бұрын
Excellent video
@nuthingness Жыл бұрын
Thank you so much! This was so helpful !
@el-hp1lj3 күн бұрын
I tried to install these because I failed a fire inspection. They screwed on fine but they were causing my door to hit the frame on the latch side.( not even close to closing) They are much fatter than the original hinges. So I had to put the original ones back in. Do I need to chisel or route out the hinge side frame to give these more room?
@brianswelding10 ай бұрын
Great job thank you! 🙏
@Jasper743 Жыл бұрын
Thanks 🙏 for your help
@ua7pyro5912 жыл бұрын
Helpful video. 👍 Thanks
@SKANDERBEG1239 ай бұрын
God bless brother.
@BenjaminPalumbo2 жыл бұрын
Thank you
@willow_alleyАй бұрын
Can these hinges to used for the opposite purpose? Like to prevent :: cough:: teenagers :: cough:: from slamming doors?
@charlesstacy7411 Жыл бұрын
Made it easy, thanks buddy
@samu33992 жыл бұрын
Thanks
@ennellesperance11862 жыл бұрын
Thank you 🙏🏿
@Dr.Spoofs15 күн бұрын
Mine just has a Phillips screw on the bottom. I dont see a oin anywhere. It's a gate hinge.
@davemeade4371 Жыл бұрын
Thanks man, needed to see that spring loaded mechanism and was able to find out how to work on an existing one without finger pinches from a quick scan through your video
@barbarapeden75232 ай бұрын
Does it matter what position the spring hinge and 2 normal hinges are located?
@420 Жыл бұрын
Update: WOAH! My garage door has THREE of these hinges already installed, but the previous homeowner must have removed all the pins. I notice the holes are not aligned for me to reinsert pins if I buy some though. Any ideas? Update #2: Called a homebuilder buddy and he said installers commonly install the hinges upside down, so that's likely why my pinhole is misaligned. The Alan keys are all 3 at the bottom and not at the top. I'm going to flip the middle hinge and see if I can gently hammer it down a little if needed and see if everything is lined back up. Then flip the remaining two or just one depending how many are needing to close properly. I also will have to use a tap nail as my pins. Cut them down to size with pliers. (That's what they do on installs he said, and it stops the pin from ever fully going in.) Finale: Left them upside down. Used a hammer to lightly tap the bottoms up to realign the holes. Cut three tap nails down to size and made myself pins that are perfect.
@teejay26792 ай бұрын
This video could be shortened to 2 min
@poolplexerАй бұрын
Your opinions could be shortened by 5 min
@poolplexerАй бұрын
Your opinions could be shortened by 5 min
@blazayblazay8888 Жыл бұрын
Do these ever need shims?
@oaouda7 ай бұрын
Thanks for the video. How do you remove these type of hinges to paint the door? Do I need to unscrew the hinge from the door Jam? Thank you!!
@HomeRepairHub7 ай бұрын
The would be 1 option. Another option would be to get some painters tape, and simply cover the hinge with tape. The once you are done painting, remove the tape.
@Mrscottyboy46 ай бұрын
@homerepairhub so to be clear you cannot remove the pins on this style hinge? They don’t slide out?
@HomeRepairHub6 ай бұрын
@@Mrscottyboy4 correct, there is no hinge pin. It is 1 piece.
@serviceprovider69565 ай бұрын
Thanks for the video! I just installed my hinge by watching your video. In the back of the package doesn’t give clear instructions.
@HomeRepairHub5 ай бұрын
Glad it helped. Thanks for the feedback
@mitchlukes71404 ай бұрын
How do you install a door stop hinge on this type of hinge?
@droolguy3 ай бұрын
You don't. The door stop replaces the pin in a standard hinge or pivots on it, these do not have a typical center pin, nor do they have an easy way to mount any kind of wedge to them which is what the pin mounted door stop is. Any door mounted doorstop would need to be mounted directly to the door itself, or you'd need to move to a floor or wall mounted doorstop.
@marionisperos66752 жыл бұрын
can it be installed to a 3" thick door jamb?
@SR71mydream Жыл бұрын
Those screws on the door side are more commonly referred to as thread cutting. Self tapping usually indicates the non threaded cutter head at the tip of a screw.
@kmattorney5 ай бұрын
My top of the circular hinge is flat. There is no Allen key hole. Only just the little hole on the vertical cylinder, and a bunch of little pin holes down at the bottom part of the cylinder. Any idea how to load it.
@HomeRepairHub5 ай бұрын
What brand is it?
@podersa241 Жыл бұрын
The best place and time to put it is when you keeps saying close the door, close the door. Well I am done so time for a loaded hinge.
@pilgrimpassingthrough2228 Жыл бұрын
Where is the link to purchase this type of sp;rinig? Thanks!
@barbarapeden75232 ай бұрын
I bought mine at home depot
@globaltraveler23812 жыл бұрын
How do I stop a self closing hinge from squeaking?
@HomeRepairHub2 жыл бұрын
Grease, WD-40, or just change it out
@ralphtorres64782 жыл бұрын
Food Grade Sylicone keeps Lubricated for up to 6 months
@williamb28542 жыл бұрын
One other reason... Kids never closing the door! Problem solved !!! Thanks for sharing.
@matts9011 Жыл бұрын
That's why I am here😆
@goxyeagle844610 ай бұрын
Skip to minute 4:30 You welcome Thank you for this good video tho
@Opuscus Жыл бұрын
Like pulling teeth.
@davidcowan47052 күн бұрын
Everbilt hinge packaging gives HORRIBLE instructions. Please watch this first.