How To Install Corner Susan Door Hinges

Рет қаралды 321,231

Күн бұрын

Dan talks about how to prep doors for and install bifold lazy Susan door hinges. In this video you will learn how it operates, what you can expect, what you're going to get, and how to assemble and adjust the hinges. At Keystone Wood Specialties, you can order your doors bored for hinges and get the hinges from us as well. The hinges used in this video are BLUM 60 degree clip-top (79T8500.10 with hinge mounting plate 175H6000) and BLUM 170 degree clip-top (71T6550). We recommend that you refer to the BLUM literature for the hinge that suits your specific application.

Пікірлер: 72

@PeterFournier-yq7kw 2 ай бұрын

Thank you! Finally a video that presented this topic clearly, especially for someone like me who's not especially handy. I was struggling to find the correct hinges to connect the 2 doors together as ours fell apart, ordered the wrong ones twice and then finally you uttered the magic words "60 degree bifold hinges".

@markphillips590 6 ай бұрын

I appreciate your video and it seemed to have answered most of the people's questions; mine was how to mount the bracket into the shelf. I had an old GRASS hinge and since they are no longer manufactures, I purchased the Ferrari hinge; and when I have put them on, they have been in a bind. I will get it figured out. Thanks again from 2024!

@gregholder1339 2 жыл бұрын

This was very helpful. I have never installed hinges on a lazy susan cabinet and wasn't sure how to do it. Thank you!

@rickhilton9108 29 күн бұрын

Thank you for stating the hinge on the cabinet is 170 that is what I needed to know

@RedBeardCarpentryWoodworks 3 жыл бұрын

Thanks for the demo!!

@thomasgonzales9689 Ай бұрын

You’re a Complete pro! Thank you.

@ToolMetrix Жыл бұрын

This is superb! Thank you for sharing.

@Ukepa 2 жыл бұрын

very good video. I didn't know this door arrangement was available

@carontauber8046 3 жыл бұрын

Thank you, very helpful

@charlesrose7212 2 жыл бұрын

Great explanation! Thanks! 😀

@marcyrose2121 8 ай бұрын

Thank you your video is the only one that answered my question

@svetlanlesny259 3 жыл бұрын

perfectly executed ! :)

@mohamedshams8014 2 жыл бұрын

Thank you! very helpful video

@tameralaskaris6909 2 жыл бұрын

Very helpful!

@RiotGrrrlMeg Жыл бұрын

This was really useful, thank you.

@farnorth1587 11 ай бұрын

thankyou , good tip on shelf and hinge position

@trinanestor6653 2 жыл бұрын

Thank you thank you thank you! Did I say, "Thank you!" Because if I didn't, Thank You!!!

@MrActionjs 4 ай бұрын

Thanks it would have been helpful if you hadn't pre drilled the hinge plate and shower how you aligned the plate.

@CinHalCedHerChance 2 ай бұрын

I'm pretty sure the doors come with the holes pre-drilled, mine did.

@arthurdanieln5895 3 жыл бұрын

Very clear explanation n video presentation. Amazing work

@Lookingforneutral 3 жыл бұрын

The cup hole that goes past. Do you have a measurement of what that is required for them hinges?

@SAMRAT5130 3 жыл бұрын

please comment what type of hinges are use in for corner unit

@powerofknowledge7771 2 жыл бұрын

This was the most helpful video I've seen about this hinge! I've been looking all over the place for something like this to help me understand how these hinges work. But I still have one burning question that I still haven't gotten an answer to! How far can you adjust the door spacing?! What is the widest you can adjust it?! I'm looking for something that will swing an inset door around a 3/4 inch baseboard that's laying right next to it Side by side. It's not a typical setup.

@keystonewoodspecialties1973 Жыл бұрын

Thanks so much for the comment! For the scenario you're looking for, do you have a picture or drawing that you could send me to help be better understand your specific situation? Would love to help you figure out a solution. ~Dan

@powerofknowledge7771 Жыл бұрын

@@keystonewoodspecialties1973 Thank you for responding! Here's some pics. I'm in the middle of remodeling this kitchen. Had to remove baseboard for doors to swing open without whacking baseboards. Now I'm looking for a more permanent solution. I may just turn these back into a bifold door which is what it used to be. The brown cabinet on the left will not be there when I'm done with the remodel. Pic 1: drive.google.com/file/d/1QmvqHRnL3zDSgUEOEQ933GSAtw0hFuv7/view?usp=sharing Pic 2: drive.google.com/file/d/1Qv3fUWtgqy7kjL9Kx_ONcjRaNb3uAMyM/view?usp=sharing Pic 3: drive.google.com/file/d/1QwlFI8sEBdGgIufdYvUbW9WCJddNPG87/view?usp=sharing

@keystonewoodspecialties1973 Жыл бұрын

@@powerofknowledge7771 Thanks for the pics! That helps me understand the situation much better. So there are a few things going on here. The biggest issue I see is the installation of the hinges. The hinges should be installed so that you only see the barrel of the hinge when the door is closed, and the two flats are essentially touching each other. These hinges might also be too small to give the door enough swing clearance (they look like cabinet door hinges), so you may have to look at getting bigger hinges (interior door hinges). Another thing that will help is installing casing around the opening. This buys you a little space between the hinge and the start of the trim, and most casing tapers in thickness as it nears the door, which aids in door clearance. Hopefully that helps! Have a great day! ~Dan

@powerofknowledge7771 Жыл бұрын

@@keystonewoodspecialties1973 Thanks for taking the time to respond! Those are great ideas! I was just trying to do less work on this project by just getting some different hinges that swing out. lol. I guess there isn't any such thing. Perhaps adding a casing is the only way to go.

@naderkeryakes9493 3 жыл бұрын

Thanks a lot for this wonderful explanation, my question please: what is the distance from the center of the 60 degrees bi-fold hing to the edge of the door to make the correct drilling? Thank you!

@keystonewoodspecialties1973 3 жыл бұрын

The correct distance from the edge of the door to the center of the cup drilling for the bi-fold hinge is 12.5mm.

@bornofthesea5761 Жыл бұрын

This looks great. We are designing out wardrobe and need to do something like this. Do the hinges take the weight of the door well over time? Thanks

@keystonewoodspecialties1973 Жыл бұрын

Thanks for the comment! When used in a lazy susan application these hinges hold up really well. A typical Base corner cabinet is 36" x 36", which leaves a 12" x 12" face if the ends are 24" deep. So the normal lazy susan doors are typically 12" wide or less, which means these hinges are not subjected to a lot of weight in a susan application. If you're using these with a different setup and much larger doors I would check the weight rating with Blum and possibly do a test setup. Hopefully that helps! Have a great day! ~Dan

@rebeccawoody6374 3 жыл бұрын

Have you found any hinges like this, especially the 60 degree ones, that you don't have to bore into the door. I have now spoken to more people than I can count and returned five types of hinges and spent stupid amounts of hours trying to find lazy susan hinges for my doors. They're too thin to bore into, and everyone keeps giving me the wrong hinges.

@TheNewports 8 ай бұрын

I have a cabinet that is 80" tall that i am considering using a hinge like this on. Instead of a lazy susan it is a large corner cabinet in a closet. Can I use 4 or 5 sets of hinges and use these hinges in the same way as you use here on a base cabinet.

@sandywjo5 4 ай бұрын

Great video! I have one question, I ordered new hinges, but notice that the one that sets in the bored out hole on cabinet door is coming away from the door about 1/8 inch, and you can't screw the screw any tighter. Does this mean something inside the door has rotted and will not even hold a new hinge there where that screw is? The hinge is tight enough to stay on, just not sitting flush in that hole.

@keystonewoodspecialties1973 4 ай бұрын

Thanks for the question! Based on your description of the situation I believe there are actually two issues here. I believe the new hinges probably require a deeper bore; that's likely what's preventing the hinges from sitting flush against the door. It's also possible that there's something under the hinge, maybe a piece of debris, that's preventing it from going against, so check that first. And the first problem likely caused the second problem: loose screws. The original screws could have been a larger diameter than the new screws and/or the new screws were over-torqued trying to get the hinges to sit flush with the face of the door. The result is a stripped out screw hole. My recommendation here is to either switch to a larger diameter screw or drill out the screw hole with a 1/4" drill bit, glue and plug it with a 1/4" wooden dowel, and then pre drill and reattach the hinges. Hopefully that helps! ~ Dan

@ericlind3569 7 ай бұрын

Are both doors the same equal width?? Or is one door 3/4” less than the other with all the cups drilled in it, to account for the door thickness??

@ToñoFigueroa-m2t 18 күн бұрын

De casualidad estos videos los tienen en españo

@jarrydubbelyu2166 3 ай бұрын

When boring the middle cups on a thermofoil door, will thr bit tear apart the thermofoil coating when blowing out the side?

@keystonewoodspecialties1973 3 ай бұрын

Hi Jarry, that is definitely a possibility! I always recommend testing it on a scrap piece first, if you have one. And if you're consistently getting tearout on your scrap piece I would recommend switching to a different type of corner hinge. Salice makes a hinge that uses a more typical cup drilling that doesn't cut into the edge of the door. Hopefully that helps! ~Dan

@Pyxe_ZA 3 жыл бұрын

The hinge swings both ways ☺️😅

@jamesonkruger6989 2 жыл бұрын

I wish you would've shown how to adjust the other2..is there no up/dn adjustment?

@keystonewoodspecialties1973 2 жыл бұрын

Hi Jameson, Are you referring to the 170 degree hinges? If so, the height adjustment on the 170 degree hinge is the same as the bi-fold hinge: the adjustment is actually on the mounting plate, and the 170 degree hinge has an access hole that allows you to get a screwdriver through the hinge to the height adjustment on the mounting plate. Hopefully that help! Let me know if you have any other questions. Have a great day! ~Dan

@dannystephenshiking951 2 жыл бұрын

Awesome video! Got a question. Does the same mounting plate fit the 60 and 170 degree hinges?

@keystonewoodspecialties1973 2 жыл бұрын

Hi Danny, glad you liked the video! I do use the same mounting plate for both hinges in the video. Have a great day! ~Dan

@ericlind3569 Жыл бұрын

@@keystonewoodspecialties1973 great video, are the plates you’re using to mount these hinges a 0mm, 3mm, 4.5mm etc?? Also, going through a supplier catalog for Blum hinges, I don’t see a 60degree bi fold hinge anymore. Did they update this to the 90 degree clip top bi fold self close hinge?? Do you know Blum’s part number for the 60 degree hinge?? Thank you!!!

@ericlind3569 Жыл бұрын

@@keystonewoodspecialties1973one other question, how do you go about ordering the correct door sizes for the opening with these hinges? Are there any “gotchas” to look for??

@keystonewoodspecialties1973 Жыл бұрын

@@ericlind3569 Hi Eric, Thanks for the questions! We listed out all the part numbers for both the hinges and the mounting plates in the description. You can use a different plate for the 170 degree hinges, based on what overlay you're looking to have. The 60 degree bi-fold hinge is on page 36 in my concealed hinges catalog. There is also a guide for calculating door sizes on the same page. Hopefully that helps. Happy hinging! ~Dan

@ericlind3569 Жыл бұрын

@@keystonewoodspecialties1973 I just saw the part numbers, thank you for that. However, I don’t see a link for your door calculating guide or page?

@sanjoeamaranto1044 2 жыл бұрын

What is the distance of the hole of that concealed hinge from the side of the wood? Normal hinges usually can be installed 2.3-2.5mm. Do the same applies?

@keystonewoodspecialties1973 2 жыл бұрын

Hi Sanjoe! The hinge that attaches the door to the cabinet is the 71T6550 hinge (Clip-top 170 degree) with the 176H6000 mounting plate, which is a "zero" plate. You can either bore the door at 2.5MM DBE, which will cause the door to overlay the cabinet by 1/2", or you can bore the door with an 8MM DBE, which will cause the door to overlay the cabinet by 3/4". Hopefully that helps! ~Dan

@othmanetv971 3 жыл бұрын

Good i vesit your Chanel thank you for this vidéo

@russellgilbert6493 3 жыл бұрын

You should of shown people how it works on the unit itself

@berbababy Жыл бұрын

Hey! What's the centre measurement for the 'half-bore' hole? I know it's a 35mm bore, but how far from the edge should I start my drill?

@keystonewoodspecialties1973 Жыл бұрын

Hi Marco, thanks for asking! The current Blum spec book indicates 12.5mm from the edge of the door to the center of the bore. And yes, the bore diameter is 35mm. Hope that helps! ~Dan

@jonbeth44 4 жыл бұрын

what is the name or manufacture of the hinges that connects the doors or are between the two doors?

@keystonewoodspecialties1973 4 жыл бұрын

The hinges used in this video are BLUM 60 degree clip-top (79T8500.10 with hinge mounting plate 175H6000) and BLUM 170 degree clip-top (71T6550). We recommend that you refer to the BLUM literature for the hinge that suits your specific application.

@tektrades7539 3 жыл бұрын

"So it swings in two different directions"... Kinky!

@fishlover4523 Жыл бұрын

My left ear is happy while my right is sad

@Butterfly-zs2pc 3 жыл бұрын

I hate the design of the corner cupboards, the door being the biggest nuisance. To hard to get things in and out. You have to contort yourself to get things in and out of the cupboard. I hope they come up with something better, user friendly and practical.

@Livey01 8 ай бұрын

Corner triangle drawer... My partner made one and it's amazing

@josephbohme7917 2 ай бұрын

You would expect to have shown the system installed-= without that it would seem no one has one. It just does not show the in use in kitchen, utility, easier or difficult