I am a female learning the trade. I just came across your videos and I am finding it real easy to understand. Thanks guys great videos.
@ElectricalInstallationEEE3 жыл бұрын
Thanks a lot but may sure you love the trade because only a few female i know love it.
@raymond37223 жыл бұрын
This is the most informative video I have ever seen on how to run conduits before DECKING.
@ElectricalInstallationEEE3 жыл бұрын
A lot of key points are in this video
@raymond37223 жыл бұрын
Yes you definitely goes in real depths.
@LelewaVEVO Жыл бұрын
I am currently underground my industrial training... This video really helped me...
@starlxrd8682 жыл бұрын
from trinidad currently 18 learning the trade thanks for teaching me this
@ElectricalInstallationEEE3 жыл бұрын
A lot of important steps in this vid
@jellyslogocrainer73753 жыл бұрын
kzfaq.info/get/bejne/fb5oe8pn0L21iX0.html
@renaldodavidson77562 жыл бұрын
Yow a unu seh easy does it
@nigeldavids5213 жыл бұрын
Again I must applaud you very the knowledge you are sharing
@paulspence55342 жыл бұрын
Thank you general. Trust mi this video work wonders for mi. Finally grasp the concept
@kenroycampbell3542 Жыл бұрын
Want more valume g jus that need fi a hear every work u say caz its important. Other wise love u work neet and proper big up. Lava grong
@westernstar49642 жыл бұрын
So clear and informative. Shoutout from Barbados
@ElectricalInstallationEEE2 жыл бұрын
Nuff respect shout out my Barbadians
@jermainecowan61342 жыл бұрын
WELL DONE I Have learn a lot from this video "RESPECT"
@kevinmukabwa4020 Жыл бұрын
Thanks for more information in piping keep up bro
@strydah8971 Жыл бұрын
Good video
@emmanuelsalihu97265 күн бұрын
Nice work sir. I want to ask, how did you learn how to do electrical pipping
@chikegerald23522 жыл бұрын
I admire your work his nice .
@Randy._1law2 ай бұрын
respect bro
@rayonplummer96153 жыл бұрын
great work bro, good explanation. keep on doing well, first time seeing A video for decking.
@ElectricalInstallationEEE3 жыл бұрын
Appreciated
@MrClarkestown3 жыл бұрын
Cement bags are underrated in construction
@ElectricalInstallationEEE3 жыл бұрын
Lol it is a usefull piece of material in many ways trust me.
@tonpotv8145 Жыл бұрын
You have done so much well how I wish I can work with you
@d.p.36123 жыл бұрын
Excellent video. Continue the great work.
@ElectricalInstallationEEE3 жыл бұрын
I will
@jamelectro9623 жыл бұрын
Nice work as usual 💯
@peterrodney13772 жыл бұрын
great work
@dajuiceguy25813 жыл бұрын
Nice video. Instead of jackhammering the beam, why didn't you rough-in the pipes in the ring beam before the concrete was pour? And why is the ring beam poured separate to the slab? In the island where I am from, we do one complete pour (beam and slab) so there are no cold joints.
@ElectricalInstallationEEE3 жыл бұрын
I wasn't around at that time otherwise it would have been much easier
@nyconmckenzie43613 жыл бұрын
Love work mi genna
@electricalsphase1 Жыл бұрын
nice job but change your voice, you should speak loud and clear
@Eng.Khalid_Yahia2 жыл бұрын
Informative video thank you
@hosraiyan2 жыл бұрын
great video on decking process,can you share the diagram on what you done or doing for easy and well to understand??
@h287213 жыл бұрын
Oh and nice work, very informative 👍
@ElectricalInstallationEEE3 жыл бұрын
Thanks! 👍
@jamelectro9623 жыл бұрын
All da binding wire ting deh, mi done wid dat... I put tie straps on the material list these days. Lol
@SweeT2IE2 жыл бұрын
God bless you for this information shared Please how do you calculate the overall load for the house inorder to know the right fuse rating to use?
@opssonopsson82822 жыл бұрын
You can estimate that buy the number of "heavy appliances" you intend to run in the house. For most residential buildings with just ACs and heaters, 200amps at 415v is enough.
@loushainereid37282 жыл бұрын
I like the way you explain how to pipe up a decking but I don't understand how to run the pipes from the switch to the light . I am doing a small decking i am just putting in 2 lights just want to understand it thanks
@nadel93 жыл бұрын
Nice work.. One thing of the things I've learned is work smarter not harder.. (not referring to shortcuts)..I guess you have your reasons but why not use duct tape around your boxes instead of stuffing them with cement bags.. Advantages of using duct tape.. 1 much easier, 2, it covers the holes for the screws from behind so concert won't get into them.. 3.no concert gets into the box. 4.for some people it's very easy to clear inside your box when you're ready for it.. Maybe you've been doing it for years but bending conduit on your knee have to stop before its too late. It's like being a professional opening soda with your teeth for years until your teeth start breaking up...you'll save your self surgery. Yes it's easier and faster on the knee but dangerous.. There's other ways to do it only with bending spring and your hands. Or shoes.
@ElectricalInstallationEEE3 жыл бұрын
I use hands as well not knee only , but duct tape i've seen jobs where it was used and concrete get into it so it depends on how u stuff your boxes and pipes for me i've been doing this for years and haven't had that problem b4 so it have to do with how u do the stuffing plus it is more of a time consuming thing , papers are easy to take out after very easy , the only problem i had is work men steps on our pipes especially the couplings and birst them and sometimes run the barrow on the pipes and crimp them
@nadel93 жыл бұрын
@@ElectricalInstallationEEE OK cool, I'll give this a try may as well work better than duct tape. My only concern is the holes for the screws at the back of the box
@ElectricalInstallationEEE3 жыл бұрын
Don't think the screws at the back necessary , only ones that are necessary are the ones where the receptacles would screw through and they won't be block only difficulty those would give is when u don't unscrew the screws that comes with it most times these screws give a hard time to take out that's why i took them out when installing them if it is metal
@MrClarkestown3 жыл бұрын
This has to be the hardest part when preparing the house for wiring, I do electrical work sometimes but a decking this size would probably give me a fight because there are so many pipes.
@ElectricalInstallationEEE3 жыл бұрын
I know what you talking about my friend i've been there but now it get easy for me and it could have had more pipes if i had turn pipes up plus adding radio to it etc
@MrClarkestown3 жыл бұрын
@@ElectricalInstallationEEE exactly
@user-iv2ez3ym6j Жыл бұрын
Good indeed, but sorry doesn't it need extra paip??
@education91352 ай бұрын
What is under that wood u put the 5 way connector box, is it ceiling or
@darnelltomlinson83132 жыл бұрын
Hey bro I just saw ur video an its really helpful an neat an in instrested, two questions I wana ask for the downstairs outside lights an the upstairs switch how do link the upstairs switch to control downstairs outside lights
@marvinwilliams29223 жыл бұрын
Love this video
@ElectricalInstallationEEE3 жыл бұрын
Thanks a lot👍
@minarockson5577 Жыл бұрын
Pls what size of generator is recommend for three bed room and hall with 3 AC and 3 water heaters. And the generator cable as well. Pls help me.
@charlesokoh33733 жыл бұрын
Nice job I’m loving it already ♥️ 🇳🇬 Where should I consider using the 1inch pipe?
@ElectricalInstallationEEE3 жыл бұрын
The 1" can use for a lot of things such as multiple circuits , water heater , air conditioner or even mains
@charlesokoh33733 жыл бұрын
Great! Thanks man
@aeneasbekele70843 жыл бұрын
I was many videos but they donot worry where youtuber understood or not. but this on is fantastic. bet go a head. sometimes some electrician uses sand in fan box slab installation. what is the purpose of sand inside fan box?
@MrAndreone3 жыл бұрын
Hey bro will the pvc box hold the fan are do you use concrete screws to help with installing the fan
@ElectricalInstallationEEE3 жыл бұрын
Concrete screws 👍
@carllisgreene16163 жыл бұрын
Well done Sir. ....how do you get rid of the nails used to secure the boxes?..sharp edges when pulling wires even if u break/cut them?
@ElectricalInstallationEEE3 жыл бұрын
How to get rid of it ? When the board pull down take out the papers first ,if it is plastic box like what i used just hold it with a pliers and pull it out now if is a metal then you use a trizzle place it on the nail close to the whole in the box that the nail come then use a hammer and knock it until it brust off.
@cm55692 жыл бұрын
Do you have a conduit video for two plate wiring ( feed to switch ) system on decking/slab?
@abelghide86473 жыл бұрын
In which country do you live i watch everytime i have more interesting in your video
@ElectricalInstallationEEE3 жыл бұрын
Jamaica . Thanks for watching my videos appreciate it hope you are learning something from it.👍
@blingmotions6996 Жыл бұрын
I want to know how u determine the size panel wire and breaker used?
@ndumbefelix3438 Жыл бұрын
please can you help with the calculation on how to know the number of pipes to use for specific work? please 🙏🙏
@1LAW__3 жыл бұрын
🔥🔥🔥
@ElectricalInstallationEEE3 жыл бұрын
A it man
@luxurymusic20403 жыл бұрын
Respect for the video, quick question...how many 2.5mm cables are allowed to run through a 20mm conduit?
@ElectricalInstallationEEE3 жыл бұрын
6 maximum
@luxurymusic20403 жыл бұрын
Blessings
@andrewlawrence22912 жыл бұрын
I might be late with this or to some might be a stupid question but. When doing a decking do i use a 1 inch conduit or 3/4? I am a up and coming electrician.
@surpernichalas Жыл бұрын
3/4 pipes boss
@michaelfrenchman793 жыл бұрын
Excellent content
@ElectricalInstallationEEE3 жыл бұрын
Appreciated
@daviafoota3 жыл бұрын
Remind me which wires run in the conduit pipes which is pushed down at the top of the light boxes ?
@ElectricalInstallationEEE3 жыл бұрын
You can use 2.5mm or 1 5mm single wires
@kingmal34633 жыл бұрын
So I guess grounds won't be needed for the boxes?
@ElectricalInstallationEEE3 жыл бұрын
No but still have it there for ceiling fans , chandeliers etc
@1LAW__3 жыл бұрын
👍
@labriochedor Жыл бұрын
Hi, does it make the roof weak?
@nyconmckenzie43613 жыл бұрын
Blessings brethren a 15×14 kitchen how pipe you bring down only for switch and a draw box?
@ElectricalInstallationEEE3 жыл бұрын
Once you have a feed to it only switches or a wall light pipes would be necessary to send down
@nyconmckenzie43613 жыл бұрын
Thanks
@jamelectro9623 жыл бұрын
What if they wanna install a ceiling fan in the bedroom, would that pvc box hold it up?
@ElectricalInstallationEEE3 жыл бұрын
Yes it can but i don't , i use concrete screws mainly to hold it.
@PrinceDitrainer Жыл бұрын
What's the cost per point
@christopherjackson77062 жыл бұрын
Question why do you use paper to cover those box and not duck tape 📼
@ElectricalInstallationEEE2 жыл бұрын
Both can use
@jak50cent3 жыл бұрын
So how do you price your jobs with out prints? or do you work with the same contractor so you know what they need
@ElectricalInstallationEEE3 жыл бұрын
I work with a lot of contractor and yes they know the price
@garrettalarmdepot78273 жыл бұрын
Can you make your ideos capable of full screen...box in lower right corner
@ElectricalInstallationEEE3 жыл бұрын
U mean like a texting
@h287213 жыл бұрын
What do you do when you have rotted boxes?
@ElectricalInstallationEEE3 жыл бұрын
Well if you use the word rotted i'll take that as the box is done ,what i do is if it is the ceiling one that is rotted i use a wood block over it or cut it a little wider and put in another one and if is any other boxes i just take them out and replace it .
@jak50cent3 жыл бұрын
Do you do recess lighting
@ElectricalInstallationEEE3 жыл бұрын
Yes mostly when i do offices etc only a few people out here want it at there home don't know why but i think they bring off your house
@jak50cent3 жыл бұрын
@@ElectricalInstallationEEE yes I love them, I sell the sh..t out of them here
@ElectricalInstallationEEE3 жыл бұрын
Ok
@brightmansions20353 жыл бұрын
i would do my work just the same except for the junction box at the camera slot... i pierce a hole in the cover of the box for the camera connection to go through and screw the camera on the cover of the handy box
@ElectricalInstallationEEE3 жыл бұрын
Ok but using the box instead hold the camera more firmly
@brightmansions20353 жыл бұрын
@@ElectricalInstallationEEE yes and its also neater...
@darnelltomlinson83132 жыл бұрын
How do u price a decking
@ShaniqueS3 жыл бұрын
Where are you located...do u work in st elizabeth
@ElectricalInstallationEEE3 жыл бұрын
Islandwide
@ElectricalInstallationEEE3 жыл бұрын
Links in description
@garkem3 жыл бұрын
Why pvc octagonal boxes instead of metal?
@ElectricalInstallationEEE3 жыл бұрын
Metal boxes rush too easy if the building stops there ,because a lot of times people deck there house and can't finish it in awhile so the plastic last longer.
@garkem3 жыл бұрын
@@ElectricalInstallationEEE so the inspector won't have any problems with it and would still pass it?
@garkem3 жыл бұрын
Like your work so far, really appreciate these videos, keep doing the good work and all the best.
@ElectricalInstallationEEE3 жыл бұрын
No there can't fail your job for using plastic boxes
@ElectricalInstallationEEE3 жыл бұрын
Appreciated
@jak50cent3 жыл бұрын
This is a big house, what’s the size service
@ElectricalInstallationEEE3 жыл бұрын
Really big for them not to get a drawing done but i'm used to it , a 150amp with 50mm wires maybe 70mm with a 225amp one out of both after i check my loads and circuits
@ElectricalInstallationEEE3 жыл бұрын
Really big for them not to get a drawing done but i'm used to it , a 150amp with 50mm wires maybe 70mm with a 225amp one out of both after i check my loads and circuits
@jak50cent3 жыл бұрын
@@ElectricalInstallationEEE from the looks of the roughing installation they will have more than one panel, so what’s the sub panel amps will you be using?