Always put the bracket on carb first... so u can look down the bracket to see if it lines up with the O gasket built in if not then it can cause an air leak and run like crap
@TAKEoverIAN11 ай бұрын
What parts of the linkage do you take off
@jasongallardo7075 Жыл бұрын
What throttle cable did you use
@Mlox2 ай бұрын
I put it all on its getting fuel from the tank but its not spraying into the engine
@Kevin2valid3 ай бұрын
Do I need that 212 for me to put a carb in my 100u stock?
@slurpe8357 Жыл бұрын
What all have you done to the bike
@gtanino20613 ай бұрын
Does the mikuni come tuned already?
@theclaytonshow8386 ай бұрын
What about the linkage underneath the gas tank?
@perkututperkutut8725 Жыл бұрын
wanted to buy or purchase intake manipol 6 unit (manipol) how much?
@crybabylocr40122 жыл бұрын
Did put on braket for after or no ?
@montiel33b Жыл бұрын
Do you with that hose on the bottom I didn’t see you hook it up to anything
@ryantevlin488410 ай бұрын
Hey did u have to order a new throttle cable? I ordered the same kit for my Colman ct200uxe and I haven’t installed it yet. Or can I by pass it with this carb? Also great video really helpful and well Shit my guy.
@xptics4 ай бұрын
so the stock cable doesn’t have a bead on the end for it to hook into the slide on the carb, you could either get a soldering iron and some solder and put that on the end or get a new cable
@JayBubbaАй бұрын
That’s the part I hated most with mine 😂
@AJ-uf2tp2 жыл бұрын
should i have not removed my throttle assembly on the motor? will that affect it idk i havent heard it run yet
@chrishall1025 Жыл бұрын
Have you figured that out I’m not sure if I shouldn’t have
@Cal3b5872 ай бұрын
@chrishall1025 this completely bypasses the whole throttle assembly and governor
@starlaheartless27082 ай бұрын
Did the belts come with the carburetor
@ajvanhouten76872 жыл бұрын
Have the same exact carburetor leaks a lot of gas miss around with it for two hours or one
@elliottfilms62542 жыл бұрын
I would just check all the seals
@STLWILDONEАй бұрын
1:15 INSTALL STARTS FOR ANYBODY NEEDING IT
@user-oj3fw3fw8r18 күн бұрын
Would it work on a 100cc engine
@dangotti3454 Жыл бұрын
Put the carb up n first guys trust me if it don’t line up well it won’t be an enjoyable experience
@altraveling70192 ай бұрын
Link to the carb?
@crybabylocr40122 жыл бұрын
Because I'm stuck I can put everything else on but stuck when it comes to throttle what do I do after I put carb and gas line on I just unhook old throttle and hook new one up to carb and it will work 🤔 ps I have 79 cc predator egine very simple
@elliottfilms62542 жыл бұрын
You might need a different throttle cable to match carb!
@madshaman3911 Жыл бұрын
Whats the link to the parts
@shushunliu65725 ай бұрын
Do I have to remove the governor arm for my 212cc since I have have governor removed will the governor arm effect my engine with high idle since I have the mikuni installed just curious?
@lilbitotoxic3 ай бұрын
did you findout? should i remove it
@shushunliu65722 ай бұрын
@@lilbitotoxicyeah it’s fine after I started mine up it did no high idle effect just ran quietly with choke on
@Harristunerracing5 ай бұрын
Fun fact yall before y’all put that carburetor on there you haft to remove the ! governor ! If not it will break of in to you motor so that’s one thing he didn’t show you
@Gera-zm4etАй бұрын
So the governor will break?
@LovejoyBoi785Ай бұрын
@@Gera-zm4etDEFINITELY
@isaiahperez7010Ай бұрын
It’s that a stock motor
@Deucealive7519 күн бұрын
It won't break if RPM is limited. I wouldn't trust it 6K RPM and up. I use a small bracket bolted to the head to connect the spring to. Governor just pulls on it like it does with the stock carb. I'm running 5K RPM and under so it's not a concern.
@b-stodomingokenluii92026 күн бұрын
@@Deucealive75how to know if how much rpm you running like if you doing 50mph is that low?
@baudeliodiaz4094 Жыл бұрын
Pulling hoses, taking nuts and bolts pretty much easy to figure out but the ONLY special part of the job you Did Not take time to explain...taking off and putting back the cable that controls the amount of gas put into the mix. The cable that is activated when you push on the gas pedal
@chrismitsven85448 ай бұрын
What kit is this?
@teshuvahemmet3036 Жыл бұрын
Good job 👍
@davidhammond37212 жыл бұрын
Whare can I get some
@janiceuga87852 жыл бұрын
hm ,package deal ?
@dangotti3454 Жыл бұрын
You just did a governer bypass if I’m not mistaken. Upgraded your flywheel?
@jacklivingston4182 Жыл бұрын
i’ve done the same thing but haven’t upgraded my flywheel or rod. just have to know the engines limits
@Cal3b5872 ай бұрын
@jacklivingston4182 the valves start to float at 5500rpm as long as you don't pin it for extended periods of time your good
@Hitech8211 ай бұрын
Nice work son..
@zakrYAH2 ай бұрын
What about the loose piece?That's attached to the governor on the top underneath the gas tank is that important Do you need that in a certain direction
@buddahmayne92732 ай бұрын
Most people remove the governor
@Yumm-qk2lk2 ай бұрын
After removing the govenor and governor arm theres a decent sized hole that might be a pain in yhe ass to remove
@xpticsАй бұрын
just take off all the linkage and the arm and leave the governor in the engine that’s what i did
@aidenbecker6325Ай бұрын
Can you link everything in the description or something otherwise this video is damn near unless unless you already magically have the same filter card and manifold
@picklekondor791 Жыл бұрын
What do you do with the extra black tube hanging out the bottom
@wonderingwildling2598 Жыл бұрын
Zip tie it to the frame and angle it down towards the ground, or you can connect it to a catch can and strap the can to the frame but it doesn’t matter either way.
@troyholland3436 Жыл бұрын
Do I half to remove the Throddle linkage ?
@cuh_202311 ай бұрын
You don’t have to but to me it just looks way better with it off
@trokiandokeh1836 Жыл бұрын
Do i need to rejet it or is it already good for stage 1
@cuh_2023 Жыл бұрын
You will need to reject it to like a 120 or 115 jet
@troyholland3436 Жыл бұрын
Can I do this with out removing the Throddle linkage???
@cuh_202311 ай бұрын
You don’t have to but then theirs just useless part on the engine
@andrew_the_coin_collector85842 жыл бұрын
How do you install the fuel lines
@elliottfilms62542 жыл бұрын
Part 4:07 on my video there is a close up on the carb, there should be a brass nipple that you pith the fuel line around! And then hook it to you gas tank the same way!
@carsonlarabie Жыл бұрын
Does anyone know if this setup would work on a Baja 196cc
@125club Жыл бұрын
Wonder the same just got one yesterday
@Cal3b5872 ай бұрын
@@125clubtheir both clones of the same engine your good it'll fit
@richardhammah9887 Жыл бұрын
would this work on a stock massimo mb200
@elliottfilms6254 Жыл бұрын
Yes it should work, just make sure you get the correct size carb.
@Dwp9112 жыл бұрын
What size fuel line did you use ..thank you in advance
@Tota1Everything2 жыл бұрын
Should be 3/8s
@elliottfilms62542 жыл бұрын
It should 3/8. It also depends on the carb!
@Tmask3211 ай бұрын
So what do you do with all the other linkages??
@daejuan2829 ай бұрын
you don’t need them
@561jitt2 ай бұрын
Can I put it on there without the extra manifold😂? I juss don’t like how it sticks out
@xpticsАй бұрын
won’t get a good seal, plus the cylinder head gets really hot and the intake helps mediate that
@Ohio_Hobbies_Guy4 ай бұрын
What do i do with the governor? We arent removing it.
@undagroundhustla3 ай бұрын
Very good question.🤔
@Cal3b5872 ай бұрын
Just leave it in their as long as you don't upgrade the valve springs the stock ones will float before it gets too high of rpm
@deutschlandgaming4079 ай бұрын
Need help at 2:39 what size nuts do you put on the exist bolt?
@Geneva_suggestions19 күн бұрын
My size
@noturtleleftbehind2242 Жыл бұрын
did u have to remove the internal governor for the new throttle set up
@chrishall1025 Жыл бұрын
That’s what I’m wondering did you ever figure that out?
@ItsLando Жыл бұрын
@@chrishall1025 No u dont need to remove the governor inside
@Mattydaddy80 Жыл бұрын
@@ItsLandoso how did you connect it to the carb?
@ItsLando Жыл бұрын
@@Mattydaddy80 the throttle cable goes into the carb so the throttle linkage on the predator isn’t being used so u can just take that all off and the governor arm isn’t being pulled with all that linkage so the governor just didnt kick in my bike does like 60 with the mikuni and the governor is still inside the motor 🤷🏻
@Mattydaddy80 Жыл бұрын
@@ItsLando so is the governor arm just sitting there? It doesn’t affect the engine at all?
@gr35132 жыл бұрын
Would this work on a honda clone? I got the bt200x. I always find videos but every vid I watch they have a predator 212 engine
@elliottfilms62542 жыл бұрын
Yes it should if the bolt patter is the same!
@gr35132 жыл бұрын
Thanks for the quick response brotha looking forward to your next vids
@jasonjulian12 жыл бұрын
It'll all work perfectly on the bt200x or any Coleman mini bike . I juet installed a vm22 and adaptor on my rb200, basically identical.
@Fiatfan Жыл бұрын
Where did you get the air filter?
@TeddyLoaf3 ай бұрын
i got the same thing as him but black, amazon, it comes with the carb
@antoniojaime42539 ай бұрын
Both of my bolts got stuck bro
@trokiandokeh1836 Жыл бұрын
I have a stage 1 exhaust and a tc do i have to get another jet or is it adjustable
@elliottfilms6254 Жыл бұрын
You shouldn’t need another jet unless you are running a bigger engine or a different fuel line size.
@Cal3b5872 ай бұрын
Yeah throw a 110 jet in it if you have a different exhaust or else you'll run lean
@Deucealive7519 күн бұрын
@@Cal3b587 Others need to tune to their engine and environment. A 110 jet worked for you but may not work for others. My stock 196's with a header pipe and silencer ran best with a 120 main. My built 196 likes a 125 main jet.
@christopherflores6751 Жыл бұрын
Hi what carburetor is this I am trying to buy it
@danielclouse1546 Жыл бұрын
YOXUFA VM22 Carburetor Carb
@J_ake Жыл бұрын
can i just use the stock throttle cable?
@jacklivingston4182 Жыл бұрын
yes
@elliottfilms6254 Жыл бұрын
I will be coming out with another video answering all the questions so ask them in the comments!!
@dallas749 Жыл бұрын
what did you do about the govenor? does it still limit at 4000rpm
@Trains_n_stuff082 жыл бұрын
Did the carb you got needed to be re jetted
@elliottfilms62542 жыл бұрын
No it was perfect
@Trains_n_stuff082 жыл бұрын
@@elliottfilms6254 oh ok thanks
@slim2peezy2812 жыл бұрын
@@Trains_n_stuff08 I would suggest jetting them so they won’t bog at full throttle
@stonerboiphoenix87322 жыл бұрын
Can I put that carb on a 49cc engine
@Ypn_m5 Жыл бұрын
no
@jaydenmcmillen6748 Жыл бұрын
What jet did you run?
@Cal3b5872 ай бұрын
I'm running a 110 jet on my lifan 196cc with a straight pipe and it runs good
@mikiecastro39572 жыл бұрын
Will this fit on tilly 212
@viceanime76852 жыл бұрын
it should theyre all basic honda clones
@Frank_3362 жыл бұрын
Will it go on a carter brothers go kart
@Cal3b5872 ай бұрын
Does it have a gx200 clone engine?
@mohamadalhennawi842 Жыл бұрын
Do I need to remove the govonor 😅
@danielclouse1546 Жыл бұрын
if your building a go-kart or mini bike its really up to you the governor makes it so it cant go to max rpm rated for the engine so not you don't need to but its recommended to remove it and if you decide to I recommend upgrading the valve springs I put 22lb springs in my Honda gx 160 and it ran great I have since retired it but it ran amazingly
@carlosfrances012 жыл бұрын
Fuel lines ????
@B4N4N4-1DK3 ай бұрын
Yes on the predator
@joelmccall5665 Жыл бұрын
Where do you get the kit from?
@elliottfilms6254 Жыл бұрын
Amazon
@Hareelevio Жыл бұрын
@@elliottfilms6254 could you send me a link if you can
@danielclouse1546 Жыл бұрын
YOXUFA VM22 Carburetor Carb
@LovejoyBoi785Ай бұрын
Y’all gonna. Blow the motor without removing the governor
@Ghost88890REAL2 жыл бұрын
hey we have the same build with a chikuni carb!
@313madenell2 жыл бұрын
Does that carb make your bike a little faster ?
@Ghost88890REAL2 жыл бұрын
@@313madenell it should, the chikuni (if jetted right and no damage because it’s easily fragile) basically adds more fuel and air than the stock engine does
Put two nuts on the rods then you then you can just use a wrench on the first nut to unscrew it
@richardramirez-st8nc6 ай бұрын
Did it work ? Haha
@fadefrees37292 ай бұрын
Did it crank tho 🤣🤣🤣
@Its-Steven10 күн бұрын
Holy fuck dude, hold the damn camera steady!
@DollarhiteDelight2 ай бұрын
Says ur gonna show how to install it then skips over the steps of unhooking of the old one, or how u assembled the new one…wtf
@ancientdebris7102 Жыл бұрын
Yo did it Fr add +20 mph from stock
@ancientdebris7102 Жыл бұрын
Also what jet did you use? Thx
@elliottfilms6254 Жыл бұрын
Yesss it was look at the end of the video I have the before and after also a torque converter adds a lot of power!
@elliottfilms6254 Жыл бұрын
I used the jet that came With it it worked great
@Cal3b5872 ай бұрын
@@ancientdebris7102 I have the same kit with a straight pipe I have a 110 in mine
@cesarcabanillas93332 жыл бұрын
Must be nice having to order the black one they won’t ship red or gold to California🤦♂️
@elliottfilms62542 жыл бұрын
Ah darn!
@blakesmith9632 Жыл бұрын
Deal with what you got bro
@pedroferreia974 Жыл бұрын
@@blakesmith9632 literally no reason to comment that but Ight
@timothykiniris1724 Жыл бұрын
@@pedroferreia974he isn't wrong tho. Like fuck dude all he has to do is order a red air filter off Amazon
@zachfloyd4049 Жыл бұрын
Dont live in California then
@jimmartin9440 Жыл бұрын
The background music is annoying, why have it?
@richardgordon32022 ай бұрын
My guy slow the camera down next time, all over the place
@brokeblackguru9344 Жыл бұрын
Only ONE word for today: DIZZYING!!!😢 RalphyNovotney The BrokeBlackGuru
@david-bx1ox2 ай бұрын
At that point, just buy an actual Mikuni carb
@CrazyJoker482 ай бұрын
Why in the world are you using a crescent wrench? lol Do you not have a ratchet and socket set? Fixed end wrenches or even a ratchet end wrench! Crescent wrenches should only be used as a last resort when nothing else is available! They will strip the heads off a nut in an eyeblink! The 2:46 mark for example...I don't even have one in my collection because they cause more harm than help! You're a rookie in this video I can tell by that alone! But we all have to start somewhere! I'm sure you've grown wiser by now!
@Tokyo816k9 ай бұрын
I hate when peoples make videos and don’t show everything
@user-cc1tm1bh7w8 ай бұрын
ngl bro it’s a pretty straight forward assembly
@americandad4864 Жыл бұрын
Can’t hear because of the music .
@norcal8718 Жыл бұрын
Snore 😴
@emu552 жыл бұрын
not a real mikuni
@rogerrose82202 жыл бұрын
Yup!
@charliewilliams80262 жыл бұрын
What do you mean it says mikuni on it
@Tahmanakki2 жыл бұрын
@@charliewilliams8026 😂
@jeremymartin88572 жыл бұрын
Probably already know ,it works just as good and less $ . No brainer to get the knock offs
@emu552 жыл бұрын
@@jeremymartin8857 they work the same until they completely break…
@Nimbo-hn3ri11 ай бұрын
What do you do with the line that sticks out of the top of the fuel tank
@cuh_202311 ай бұрын
It’s just to release fumes from the gas tank just cut it short