Рет қаралды 592
Here's how you can install an automatic bow reloader onto your compound bow.
--------------
Link To Product:
taplink.cc/techoverflow/p/rap...
Related video:
-------------
0:00 Warning
0:07 Getting bow ready
0:42 Installing holder on bow
1:49 Getting sliding part ready
2:39 Moving Nock Set
2:57 Adding sliding part
00:00:07.799 so to start off we're going to need to
00:00:09.679 go ahead and remove this part right here
00:00:12.920 to do that we're going to go over to our
00:00:15.519 tools here we're just going to pull that
00:00:18.560 one out to the side we're going to go
00:00:20.080 for the skinniest one
00:00:22.400 here so here we got our skinny
00:00:25.679 one we're just going to go to the back
00:00:28.400 here we're just going to stick it in the
00:00:30.439 hole and then push and kind of
00:00:38.200 Wiggle just like that and now it is
00:00:42.039 out now I'm going to take this over flip
00:00:44.800 it over here and then we're going to
00:00:47.440 grab this part right here you can see
00:00:49.920 this long section right here we're going
00:00:51.399 to take
00:00:52.680 that put that right over those two
00:00:57.280 holes and then you're going to go ahead
00:00:59.280 and grab that big screw and stick that
00:01:02.320 in the big
00:01:03.439 hole just like
00:01:05.720 that now you want to go over grab your
00:01:08.240 large
00:01:09.759 tool
00:01:11.479 and screw it
00:01:17.520 in so now we're just going to want to go
00:01:19.640 ahead and move these in as much as we
00:01:22.200 can grab our small tool
00:01:26.040 here and screw them in so that they're
00:01:29.600 nice and
00:01:41.000 tight now we can go ahead and tighten
00:01:43.560 this one as
00:01:44.880 well now as you can tell it's firmly on
00:01:47.520 there it's not coming
00:01:48.880 off we're now going to grab this thing
00:01:51.799 right here and we're going to grab our
00:01:54.920 medium
00:01:56.280 one and we're going to go ahead and
00:01:58.799 remove this screw
00:02:03.920 here we're then also going to have to
00:02:05.880 remove the screws up
00:02:16.640 here I know this one seems to be a
00:02:18.840 different
00:02:28.760 size
00:02:30.840 so this tool did not work in that screw
00:02:32.840 and I think it's supposed to so that's a
00:02:34.800 problem we going to ahead and remove
00:02:36.840 that so now as you can see it slides
00:02:38.840 apart like
00:02:42.200 that so we are going to need to go ahead
00:02:44.360 and move that as well so I'm just going
00:02:46.879 to grab it with some tweezers just
00:02:49.080 putting it like gently around it and
00:02:50.640 then kind of pulling it like that gets
00:02:52.959 it unstuck and you can just kind of move
00:02:54.879 it down here somewhere and just leave it
00:02:56.360 like that so now we got to make sure
00:02:58.239 that this Gap goes in between the the
00:02:59.920 wire so we're going to go here put it on
00:03:03.200 like that and then we're going to line
00:03:05.640 it up with the wheels
00:03:07.560 there just like that and now it is on
00:03:11.920 our bow you can see so next we're going
00:03:15.040 to go ahead move our bow down a little
00:03:18.200 bit and we're going to need to replace
00:03:19.760 this top part
00:03:22.799 here and you may need to pull this up a
00:03:24.959 little bit and get it to pop back in the
00:03:28.360 right position like that
00:03:32.840 and then just tighten it up like that
00:03:35.680 now we're just going to need those last
00:03:36.799 two screws
00:03:43.239 here and now we just need to replace
00:03:45.400 that one screw right here as
00:03:50.640 well just like
00:03:52.920 that and now we have a bow that can
00:03:56.079 rapid fire