How To Install the Big 3 Upgrade Improve Your Vehicle's Charging System

No video

How To Install the Big 3 Upgrade Improve Your Vehicle's Charging System

Рет қаралды 49,208

Күн бұрын

Upgrade Alternator charging wire to Battery positive, Battery Negative to chassis ground wire and
Engine Block to chassis ground wire using 1 gauge cable that I got for a Dodge Charger and Magnum or Chrysler 300 for as little as $5.00 The cable is 13 feet long.
1 Gauge wire will provide low resistance and increase potential current flow.
All work performed on a 2004 Jeep Grand Cherokee with a 4.7L engine.
Related Video:
Engine Wire Tuck on a 4.7L Jeep Grand Cherokee Part 1 • Engine Wire Tuck on a ...
Relocate Battery on a 99-04 Jeep Grand Cherokee • Relocate Battery on a ...
How to Wire Tuck Engine Bay on a Jeep Grand Cherokee WJ • How to Wire Tuck Engin...
How to Replace and Upgrade Welder Cables for under $5.00 • How to Replace and Upg...
How to Install a Battery Disconnect Switch • How to Install a Batte...
Amazon Affiliate Links
Cable Lug Crimping Tool amzn.to/3fwWawE
50pcs Copper Wire Battery Cable Lugs amzn.to/3ucTKHC
Dual Wall Adhesive Heat Shrink Tubing Kit amzn.to/39RZ2Rp
Bernzomatic High-Intensity Trigger Start Torch amzn.to/3cDCwxa
Pack of 2, MAPP Gas Cylinder amzn.to/2Psm5ee
Milwaukee Fastback Utility Knife amzn.to/3rGDYD6
Fastronix High Current Battery Disconnect Switch amzn.to/2W4YezY
Fastronix High Current 3/8" Thru Panel Battery Terminal Connectors amzn.to/3dqsXRo
Fastronix 3/8" Stud Terminal Covers amzn.to/39srF7p
Donate to Help Support Channel www.paypal.com...
Facebook / martinbuilt-2351766611...
Disclaimer:
FYI if you click any of the product links above and end up purchasing anything I MAY get paid a small commission at no extra charge. This is one of the ways you can support the channel. Your support helps me bring out more content for all of you. Martinbuilt assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from the information contained in this video is the sole responsibility of the user and not Martinbuilt. Martinbuilt cannot guarantee against improper use or unauthorized modifications of this information.
#martinbuilt

Пікірлер: 140

@inkedbuddhist5220 3 жыл бұрын

One of my first & best mods IMO. My XJ started first try, prepped for my Dodge big alt swap,& ensure current available when needed. I used welding wire, waterproof shrink tube, & brass lugs. Upgraded batt post clamps too.

@martinbuilt 3 жыл бұрын

Thanks for sharing

@user-ny7mg3lo4e 9 ай бұрын

Jmu

@richwilson7017 3 жыл бұрын

Thanks Martin. Already got me 2 of these. 2.99 a piece is a steal. Going to get more. Great for the boat too!

@martinbuilt 3 жыл бұрын

Wow that's a great price, you can't bet that.

@dzlfreek 3 жыл бұрын

I like to grind the flare off the terminal ends so there aren't any hot spots in the shrink tube

@steveblankenship5474 3 жыл бұрын

Nice job posting this. I did this a couple of years ago on my XJ and it really made a difference, smoother running engine and no issues with the gauges.

@martinbuilt 3 жыл бұрын

Yeah I may need to do this to my XJ

@mobius-1503 3 жыл бұрын

What size ground did you use same size as this?

@martinbuilt 3 жыл бұрын

@@mobius-1503 yes, same cable 1 gauge, I just pained the red black.

@steveblankenship5474 3 жыл бұрын

@@mobius-1503 yes

@steveblankenship5474 3 жыл бұрын

Also the ground going to the body by the battery I did that #4 as well

@toddstratton9197 3 жыл бұрын

Hey Martin, I'm fairly new to your channel and being a jeep guy. Your videos are freaking great all the way around from the camera work to your explanations. Most importantly though is your demeanor, attitude, and your knowledge. Knowledge is the key to most things in life I believe and I appreciate you sharing yours.

@martinbuilt 3 жыл бұрын

Thank you for the kind words Todd, I really appreciate that. 😊

@robgarner1378 2 жыл бұрын

Currently doing the BIG 3 on our 2 Dodge Chargers, love Martin's processes, very nice, clean and thoughful. in one word, AWESOME!

@martinbuilt 2 жыл бұрын

Thank you, Rob. I really appreciate that! 🤗

@ralphcampisi9696 3 жыл бұрын

Hey Martin, great video. Just a suggestion on crimping,when doing a double crimp, first crimp starts closer to palm of lug second goes to wire entering lug

@gregj.gotham4402 2 жыл бұрын

Martinbuilt: I’m going to follow your big three cable set up for my own WJ. Always the best videos on KZfaq. Thank you!

@martinbuilt 2 жыл бұрын

Thank you, Greg, I really appreciate that. 😀

@masterdebater8757 2 жыл бұрын

Use some liquid electric tape after soldering/crimping then add your heat-shrink and you will have a forever cable that will last until the lug rots off. Seems not many people know about liquid electric tape but it is a great product especially like where you joined 2 wires in one lug and have a penetration between wires into the joint.

@martinbuilt 2 жыл бұрын

I've used that liquid tape many times and it works quite well. amzn.to/3MjrVqn

@JoshSmith-wo7zw 2 жыл бұрын

By pulling the negative cable first you prevent sparks. That's why they tell you to pull the negative then the positive. If it was a wet cell battery it could cause an explosion if it's venting alot of hydrogen gas at the time.

@xc8487 3 жыл бұрын

Jeep Cables has big7 kits, but for stock battery location.

@masterdebater8757 2 жыл бұрын

kits are over priced. wire itself is expensive Martin shows how to save and still do it right.

@gregj.gotham4402 2 жыл бұрын

U pick u save in Syracuse New York I got mine out of a Chrysler 300 today yep 👍 about $ 6.00 in the rusty east coast. Thank you Martinbuilt great heads up on parts to put to use. I’ll have the ground on tomorrow from engine to frame. Got a ground a bit smaller but the best Made in the USA.

@martinbuilt 2 жыл бұрын

That's still a really good deal.. I would imagine this time of year you had to battle a little bit of snow.

@gregj.gotham4402 2 жыл бұрын

No in fact it was 66 degrees yesterday. Still warm today but rain. Snow is all most gone. I have my receipt from yesterday I paid 2.80 for 13’ of #1 red welding wire from that Chrysler 300. WOW cheap. I also found a high performance air cleaner, and a small 90 of hose for a total of $6.00

@martinbuilt 2 жыл бұрын

@@gregj.gotham4402 That is is an awesome deal.👍

@NoWr2Run 3 жыл бұрын

Harness/ Wiring Tuck, Damn Martin WAAAAYYYY TOOOO MUCH TROUBLE FOR ME TO DO, KRAZY. GOOD LUCK WITH THAT, YA I IMAGINE IT WILL TAKE WHILE, HOLY CROW.

@allensnook7760 3 жыл бұрын

I like how you said im not running 10 to 1 compression. The whole time i was thinking yeah not yet!!you know your always brainstorming for more power,ha,ha..know this is old vidieo but i was revisiting trying to see if you had info on were to get those nutsetter tools.i got a few projects that would benifit,snooky pa.keep ur top side up martin!!!!

@martinbuilt 3 жыл бұрын

The engine I have on the stand will be 10:1 if I ever get it built. Here is a link to that tool RZX 16" RIVET NUT TOOL amzn.to/3tGHSyl

@bobbyemick4251 Жыл бұрын

Love the video. I got my big piwer cable out of a bmw 740 IL any time i build a car i buy one to scrap an i take all the wire out of it an use it on my build

@martinbuilt Жыл бұрын

Thank you. I'm glad you liked it. Yeah. I've seen the battery cables on some of those BMWs. Those are even bigger than the one I got out of the chrysler.

@DrHavok1 3 жыл бұрын

Thanks Martin I never knew they were using wire like that in that vehicles in seriously going to go snag me up some new wires for my zj

@dwj7386 3 жыл бұрын

Great job and informative. Only thing I would do different would be to have a vent tube for battery due to fumes. Could be just as simple as hose and grommet that runs outside cab.

@martinbuilt 3 жыл бұрын

Thank you, there is actually a 3/4 hole vent toward the bottom of the battery box and there is also the battery temp sensor mounted at the back of the battery Box that also vents any battery games if any. One thing nice about the Optima battery that it is a sealed battery and only would it vent would gasses during an overcharge situation.

@masterdebater8757 2 жыл бұрын

I think those optima bats are AGM so no vents needed

@joaquinaguirre2976 Жыл бұрын

Thank you. I appreciate the info, I will try to upgrade to my toyota camry.

@cbronsonda13th37 2 жыл бұрын

Do you guys know about autotechengineering they have alternators for imports like the 10th gen Honda civic

@jdsrcs8061 3 жыл бұрын

Great work Martin!!! My 04 WJ is jealous of your 04!!!🤣🤣

@martinbuilt 3 жыл бұрын

Thanks 👍

@1stzjtruck706 3 жыл бұрын

Another great job and video.

@martinbuilt 3 жыл бұрын

I appreciate that

@paultavres9830 3 жыл бұрын

Only problem with a battery cut off switch is you have to do a PCM drive cycle every time you turn it off Basically like clearing your codes Then perform your drive cycle to reestablish your monitor systems test cycles Such as evap 02 sensors cat ect

@martinbuilt 3 жыл бұрын

I only use the cut off switch when servicing the vehicle much easier than pulling the cover off the battery box and removing the negative terminal, it also makes a great safety feature.

@danhambrick6331 3 жыл бұрын

Nice job as always Martin..

@martinbuilt 3 жыл бұрын

Thanks again!

@kennygerald3458 3 жыл бұрын

What video do you show how to remove the 1 guage wire from the dodge charger/magnum? I really want to watch it

@kennygerald3458 3 жыл бұрын

I rewatched this video and seen the video recommendation pop up thanks!

@jerrywhite7269 3 жыл бұрын

Kenny Gerald, Is there a timestamp of the video Martin mentioned ? I too, have missed it. Thanks in advance,

@laidbackrich_nyc6090 3 жыл бұрын

My mechanic did not sand painted part of chasis. It didn’t improve the voltage at all.

@ChickenNoodle0404 2 жыл бұрын

Any advice on how to get a stuck pitman arm off? Mine is stuck on there good.

@martinbuilt 2 жыл бұрын

I've always struck a hammer on the end of the Pitman arm bolt bolt and also using a hammer on the side of the Pitman arm. Continuously tightening the Pitman arm bolt And it always comes off for me.

@babayaga5176 8 ай бұрын

Hey Martin your Jeep is 4.7 correct? Well my 4.0 doesn't have a power cord from the battery to the alternator. It has a power cord from the alternator to my fuse box. Is that the same cord essentially?

@DanBrino 3 жыл бұрын

I think you're the guy my Uncle Scott told me about. You're from Henderson right? He helped you fabricate something for some weights you made.

@martinbuilt 3 жыл бұрын

Yup I'm the guy, your Uncle has helped me out several times.

@scjeepHO 3 жыл бұрын

Great job as always.

@martinbuilt 3 жыл бұрын

I appreciate that, thank again!

@chucktaylor4958 2 жыл бұрын

Very helpful. Thanks.

@martinbuilt 2 жыл бұрын

You're very welcome. Thank you for watching.

@eggr17ify Жыл бұрын

Do you recommend fuses from alternator to battery and battery to fuse box?

@LZDEN 3 жыл бұрын

great job Martin,i liked the made in the U-S-A...but what about made in Great Britain...hahaha.

@teamblack3star445 3 жыл бұрын

What is the special terminal called that leads to the alternator? It already came on your part from the junkyard, It’s got like some arms on it that you gotta spin into the alternator

@Chromedome-ss6mg 4 ай бұрын

That cheap cable isn't oxygen free and has a lot more resistance than oxygen-free cable. You basically got to run twice as much as oxygen-free wire.

@DBThatBassMan 2 жыл бұрын

we're did you get the wire from

@martinbuilt 2 жыл бұрын

Here is a video that I did that will show you exactly where I got this cable and how to remove it for around $5. kzfaq.info/get/bejne/nNqfYJSksazYYHU.html

@sgt.7133 2 жыл бұрын

Is there a particular order to connect the Big 3 once ur ready to install???

@mobius-1503 3 жыл бұрын

Very intresting your talking about ground. I have the left light flickering issue when stopped and my blower motor relay keeps blowing out. Wondering if i have weak ground straps. Their paper thin

@martinbuilt 3 жыл бұрын

Yes it could be a poore ground. The ground straps may be thin but they add up to around a 14 Gauge wire.

@bumblezee Жыл бұрын

What if your battery is in the trunk? I've been wanting to install the big 3 on my 2015 camaro but the battery is located in the trunk. The only thing I can think of is run the 0g power wire from the trunk ,through the car, and to the alternator but from what i was told having "too long" of a wire can diminish the power your creating with the big 3. I have car audio that eats a good bit of it so i definitely need more power with everything powering off of the oem alternator

@martinbuilt Жыл бұрын

Since your battery is in the trunk, you probably already have one gauge cable. I would improve the ground cables then. You can also enlarge the alternator cable.

@scottstrangman7309 3 жыл бұрын

Nice work.

@martinbuilt 3 жыл бұрын

Thank you! Cheers! 😃

@salvadorebertolone 3 жыл бұрын

not sure i would solder the joint. solder is not a reliable cable connection method. as the copper hardens from vibration more strain is placed on the solder joint itself until it fails. the ground system on these vehicles is kind of not great. i would not rely much on the unibody structure to transfer much load i would keep something similar to the factory arrangement and add a battery ground straight to the engine block as many parts of the vehicle electrical system ground through the block back to the battery, which is also grounded to the block.

@martinbuilt 3 жыл бұрын

I used to work at a wire harness factory where we built harnesses for John Deere and Caterpillar and many other companies and all of caterpillars terminals are dipped in soldered.

@salvadorebertolone 3 жыл бұрын

@@martinbuilt how long ago?

@martinbuilt 3 жыл бұрын

@@salvadorebertolone 1986-1991

@DytliefMoller 3 жыл бұрын

I agree with Marting, The solder is not for securing the joint, it is to improve the joint preventing moisture from entering the crimped zone and stiffens the cable end. The Heatshrink further holds the joint to reduce "moving/bending" the wire to lug section.

@jerrywhite7269 3 жыл бұрын

Martin, I missed the video link you mention of removing these cables at the recycling yard. Would you mind letting me know which video it is, possibly by the date, or name ? Thanks, A-Fan

@martinbuilt 3 жыл бұрын

kzfaq.info/get/bejne/nNqfYJSksazYYHU.html

@gregj.gotham4402 2 жыл бұрын

Martinbuilt: I’ve looked for how you have removed the long battery positive wire from Chrysler 300 or dodge I don’t see a link under this video, I don’t find it in your video’s?

@martinbuilt 2 жыл бұрын

It should be this video Relocate Battery on a 99-04 Jeep Grand kzfaq.info/get/bejne/iqqpdtp-m6ytZWg.html

@thehannman69 3 жыл бұрын

hey martin, quick question. I have a 2004 jeep grand cherokee 4.0. I'm doing a basic big 3 for a aftermarket sound system that is being installed. Where is the location of the factory OEM ground to switch out? It's so hard to find information on the grand cherokees. Thanks, great content boss

@masterdebater8757 2 жыл бұрын

I think you prolly figured it out but when i did mine i just overlayed a lot or replaced some. 6guage for passenger side engine where i think the knock sensor is up to fire wall. 2 gauge from alternator bracket to battery, 2 gauge from battery to fender under the coolant tank (opted to not move the fuse box to replace the factory fender ground), then there is one more ground low on the engine block behind alternator i put a 2 gauge there up to the other bolt hole for the coolant tank but you can run it how you like. I choose the coolant tank because the mounting bolts already existed and it was easy to use studs over the lugs to reattach the tank. It is actually more like a big 7 wire upgrade on the WJ once you have done then all. I left the fuse box alone in mine as i was only adding 1200watt amplifier without expensive alternator upgrade and the factory should have had enough for their end (fuse box). I did notice the engine was a bit happier when the cooling fans kicked on and AC was running. Some those wires like Martin said maybe only 8guage and the flat strap on the passenger side to fire wall well i have seem more copper feeding and rc cars motor than Crysler used there my flat strap fell to 2 pieces when i remove the nut from it. I took 4 gauge back under passenger rear seat on a 100amp maxi fuse added a distribution block there with a pass through hot and 4 fusible legs. Added a Xspower AGM where Martin added his optima and found good spot just beside the E-brakes splitter box under the seats for a ground. This will all depend on how you want to do things i opted for some solid terminals that have 2 grubs screw holes of that take 0 to 4gauge and 2 grubs taking some smaller wires so i could over lay some of the factory wire since the terminals gave me so many options. I got both factory hot and negatives into 1 large grub hole per terminal and had another big hole and 2 smaller to play around with.

@signaturetile 3 жыл бұрын

Not shown in the other video, was the negative cable also off the charger?

@martinbuilt 3 жыл бұрын

I didn't use the negative from the Charger, it is only 8 gauge. The negative that I used was the same red cable I just painted it black.

@Logan-de3xx 2 жыл бұрын

Martin I’m curious, have you had any issues with your wiring in the door hinge? I didn’t realize WJ’s have this problem with the wires breaking. Just curious if it’s happened to you yet. I was thinking going ahead and fixing it before it breaks since I see so many having that issue.

@martinbuilt 2 жыл бұрын

No not as of yet. A lot of cars have this problem.

@Logan-de3xx 2 жыл бұрын

@@martinbuilt Appreciate you answering Martin. Yeah I guess we’re both lucky. I think I’m going to just pull the loom out and see if there’s any sign of wear. I didn’t realize so many WJ’s have an issue with this. Nice seeing you’re clean wiring in yours. I love how meticulous you are. It’s always the best when you do it yourself!

@hakenkreuz7076 2 жыл бұрын

I'm looking to do the big three on my 2018 JL Wrangler but it has an auxiliary battery and I'm not quite sure exactly how to do it is there any links you could send me to or any kind of help you can give me it would be much appreciated thank you

@martinbuilt 2 жыл бұрын

I would just replace the existing battery cables with a larger gauge cable, and you should be good.

@hakenkreuz7076 2 жыл бұрын

@@martinbuilt Well the auxiliary battery is buried under a whole lot of stuff in the engine bay and if I don't have to replace the cables to that it would be great that's mainly what my question was thank you for the reply.

@johnnypiper1717 Жыл бұрын

Hi I had a quick question, I was gonna change my Alt to a 320 in my 20 Ram 1500 5.7. It said I needed a shorter belt, 1/2" to 1" shorter. I seen there is 2 options 1 belt is like .58" shorter and other is .98" shorter. How would I know which one will work best, thanks alot

@martinbuilt Жыл бұрын

By the sounds of it the manufacturers already determined that either one would work just fine it's just a range half an inch to 1" shorter will work. If you're planning on Is pulling anywhere near that 300 amps I would go ahead with the shorter one.

@johnnypiper1717 Жыл бұрын

@martinbuilt ok cool yeah I was thinking of going with the 240A alt but might jus do the 320 and be done with jus in case. My amp Is a 2k which I don't plan on going any higher than that. It looks like the 240 and 320 pull around same amps at idle which I like but wasn't sure on if I should use that 1/2 belt or the belt closer to 1"

@sgt.7133 2 жыл бұрын

Question... When I do the Big 3 install... Do I completely disconnect the battery cables before installing the big 3 wires???

@martinbuilt 2 жыл бұрын

Yes, I definitely disconnect the battery before being.

@sgt.7133 2 жыл бұрын

@@martinbuilt Appreciate

@noemah3272 2 жыл бұрын

At the 15:30 mark what did you mean that the terminal wasnt touching the.. i think it was frame??? Also to solder, i just have the basic tools that i bought at Walmart, also a roll of lead type solder... Could i use that? Or is that too weak and 🔥

@martinbuilt 2 жыл бұрын

To prevent rust, paint the frame any where the terminal is not contacting the frame.

@noemah3272 2 жыл бұрын

@@martinbuilt not directly related but still on the 04 jgc 4.7 HO, i watched the fan SWAP you did and was intrigued... But i was wondering have you found another electric fan that would also fit into it? Or has another subscriber of your page come across another fan that would also fit? And easier to bolt in?

@martinbuilt 2 жыл бұрын

@@noemah3272 the 97 Mercury Villager or the Lincoln Mark VIII fan would be a good fit and perform well.

@SledsandGear 3 жыл бұрын

Hi Martin, I'm replacing the heads on my 4.7 and there are some ground straps that have fallen apart. Do the heads need a ground as well? From where to where? Thanks!

@martinbuilt 3 жыл бұрын

Yes, it's a go idea to have them. They go from the driver-side head at the rear coil bolt to the passenger side rear coil bolt to a ground stud just above the ECM.

@salvadorebertolone 3 жыл бұрын

check the block surface for flatness. these engines run a mls gasket which require an exceptionally perfect surface finshes to seal correctly. as martin said, yes theres a ground strap from each rear coil stud to a stud on the firewall.

@dem1177 3 жыл бұрын

hi! can i use 200amp wires from a jumper cable/lead? i found them to be thick and high amperage. thanks in advance!

@martinbuilt 3 жыл бұрын

As long as the Gauge of wire is bigger than what you already have I would go for it, bigger is always better.

@dem1177 3 жыл бұрын

@@martinbuilt thanks for your advice! love your vid so informative

@fatality_don7813 3 жыл бұрын

Is it true that the big 3 upgrade affects the battery after a while ?

@martinbuilt 3 жыл бұрын

There would be no negative effects from doing the big 3

@367cuba1 3 жыл бұрын

Nice!

@martinbuilt 3 жыл бұрын

Thanks 😊

@marcello033 2 жыл бұрын

I dont have a jeep but a mazda 323fastbreak (2001) I did a big 5 upgrade How do you think about upgrading the power and ground wires of the fusepanel or fusebox?(under the hood) not the interior fusepanel!! + battery to + fusebox - battery to -fusebox -fusebox to ground chassis or bodywork Is it also better to upgrade these 3 wires?

@martinbuilt 2 жыл бұрын

yes, it would a good idea to upgrade the + battery to fusebox+ I don't have any - fusebox but if your car does yes you can do those as well.

@marcello033 2 жыл бұрын

@@martinbuilt oke oke Tanx for your comment And what about the power wire from alternator to + fusebox? Is this one also needed to upgrade whene the powerwire from +alternator to + battery is alteady done? And how is it possible that you dont have any - fusebox?

@marcello033 2 жыл бұрын

@@acepairfecto5597 ok..tanx man👍

@marcello033 2 жыл бұрын

@@acepairfecto5597 Yes i watched that vid also I am gonna put some small bolts in the back frame of the alternator and connect 2 or 3 wines from the small bolts to the bolt that holds the alternator . Than connect a big wire from that bolt to the - of the battery. And a extra ground wire from the altornator to grond chassis

@marcello033 2 жыл бұрын

@@acepairfecto5597 Watch team# peranurkka Also a good explain

@michaeladams3851 3 жыл бұрын

I have a cylinder 4 misfire changed cam and crank sensors, no change. 98 2.5 Wrangler. Any ideas

@martinbuilt 3 жыл бұрын

I would check and change if needed, the spark plug, ignition wire, fuel injector and distributor cap.

@michaeladams3851 3 жыл бұрын

@@martinbuilt think could be pcm?

@martinbuilt 3 жыл бұрын

@@michaeladams3851 I doubt it, I would check the things that control the #4 cylinder first.

@markcarpenter3600 3 жыл бұрын

Also look for carbon tracking in the spark plug boots, always start with the simple stuff first.

@Airman.. Жыл бұрын

What's the output of your alternator?

@martinbuilt Жыл бұрын

160 amp

@Airman.. Жыл бұрын

@@martinbuilt 1/0 is good for 300A continuous duty if length is kept under 8ft

@artyfuffkin7805 10 ай бұрын

So you re-engineer ed your your cars electrical system , are you do you have an automotive engineering degree mr._______, let the record show he does not.