How to Install Upgraded Rocker Arms on a Jeep, Dodge 3.7 & 4.7

Рет қаралды 107,006

4 жыл бұрын

In this video, I'll explain the benefits of the 05 and later rocker arm and show how to install these upgraded rocker arms. This also a great time to replace the lash adjusters (lifters) if there is any lifter tick. Also, show you how they operate with the engine running. With an epic fail but funny.
Amazon Affiliate
Rocker Arm For 99-13 3.7L, 4.7L amzn.to/3U2rwxO
Mellings Rocker Arms amzn.to/3pzqpEC
Valve Lifters Set of 16 Chrysler Dodge Jeep 4.7L amzn.to/3VZjgBg
Valve Cover Gasket 3.7L V6 amzn.to/3ctJPED
Fel-Pro Valve Cover Gasket Set amzn.to/3aetank
Pry Bar - 4 Piece amzn.to/2yh3Y25
ABN Automotive Door Panel Plastic Fastener Clip Removal Tool amzn.to/34JPqV2
Permatex 81950 Ultra Slick Engine Assembly Lube, 4 oz. amzn.to/2qLojZO
Related Videos
How to Install 4.7HO Camshafts & Solid Lifters • How to Install 4.7HO C...
DIY Jeep/Dodge 3.7 & 4.7 Camshaft Sprocket Spanner Wrench • DIY Jeep/Dodge 3.7 & 4...
How to Install 4.7 08 Camshafts, HO Valve Springs, & Valve Stem Seals • How to Install 4.7 08 ...
Donate to Help Support Channel www.paypal.com/cgi-bin/webscr...
Facebook / martinbuilt-2351766611...
Disclaimer:
FYI if you click any of the product links above and end up purchasing anything I MAY get paid a small commission at no extra charge to you. This is one of the ways you can support the channel. Your support helps me bring out more content for all of you. Martinbuilt assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from the information contained in this video is the sole responsibility of the user and not Martinbuilt. Martinbuilt cannot guarantee against improper use or unauthorized modifications of this information.
#martinbuilt #jeepgrandcherokee

Пікірлер: 512

@oasisx27 3 жыл бұрын

Wow very informative.love all the different angles in the video as well as very informative commentary. Gives me the confidence to overtake this kind of maintenance myself.

@martinbuilt 3 жыл бұрын

Glad you enjoyed it, you can do it!

@LZDEN 4 жыл бұрын

hi Martin,and as always first class work..all the best my friend.

@martinbuilt 4 жыл бұрын

Thanks, you too!

@TCG_Jay 3 жыл бұрын

Nice work love how you showed the motor running and the oil circulating

@martinbuilt 3 жыл бұрын

Thank you, glad you found it helpful.

@jjginnard 3 жыл бұрын

Thank You for this video you saved me a ton of work I thought I was going to have to remove the engine head. You videos are so simple to follow.

@martinbuilt 3 жыл бұрын

Great to hear! Thank you, I appreciate that.

@tsschoolman4496 4 жыл бұрын

I have had an 02 Durango for the past 8 years and now it is time to take care of many of these common problems. With your help I think it will go pretty good. Thank you for the videos and all the great info.

@martinbuilt 4 жыл бұрын

Glad to help

@vr4787 4 жыл бұрын

Great as always Martin!

@martinbuilt 4 жыл бұрын

Glad you enjoyed it

@mzwandilenzimande4621 4 жыл бұрын

Incredible Value, Amazing Video, You have no Idea how much we appreciate your videos Martin. Keep well Sir and thank you again for sharing your knowledge.

@martinbuilt 4 жыл бұрын

Thank you, I appreciate that. Stay safe.

@itsmeagain8518 2 жыл бұрын

Great video. Well explained and thorough. Things explained at decent pace with good camera views.

@martinbuilt 2 жыл бұрын

I'm glad you liked it and found it helpful thank you for watching.

@felipevalles8041 2 жыл бұрын

Man That’s so cool ,Thanks for taking the time to show us the oil pressure on the rockers and lifters 👌🏻👍🏻✌🏻

@martinbuilt 2 жыл бұрын

Thank you. I'm glad you found it helpful. ☺️

@MixedGoku 4 жыл бұрын

Absolutely amazing content I wish I had found this channel before I started working on my Jeep

@martinbuilt 4 жыл бұрын

Welcome aboard!

@Logan-de3xx 2 жыл бұрын

This such a good one Martin. Thanks for this, I’ve learned so much from you. Thank you for sharing your knowledge with us!

@martinbuilt 2 жыл бұрын

Thank you. I appreciate that, and I'm glad you found it helped.

@georgesimpson7793 3 жыл бұрын

Thank you for making easy to follow videos sir you are a great teacher also

@martinbuilt 3 жыл бұрын

Glad you like them!

@ianbaumann3678 3 жыл бұрын

Finally somebody that knows what they're doing with the 4.7 and the 3.7 great videos thank you for the information 👍

@martinbuilt 3 жыл бұрын

Thank you appreciate it

@jamesviehmann4291 3 жыл бұрын

Wow! Glad now that I bagged and tagged those rocker arms off that 08 Durango that I got the cams and intake off of yesterday at the Pull A Part! Excellent demo on the rocker arm to cam lobe oiling. This whole set up will find its way onto my 03 Durango! Thanks for the heads up Martin!

@martinbuilt 3 жыл бұрын

That is awesome! you scored big at Pull a Part

@Vdubin4life 4 жыл бұрын

I really enjoy watching the videos you create for the 4.7 and 3.7 Chrysler Dodge engines. Iv been working on a set of valve covers myself, polishing them up like you have done in a previous video. I believe in my ram 4.7 as it's been in my family since 80k and I'm soon to hit 207k. No engine issues ever, knock on wood, so it's time to show love and replace lifters and the rockers. Thanks for the tips.

@martinbuilt 4 жыл бұрын

Thank you!

@constructiontech1970 4 жыл бұрын

Super tip! Great video Martin!

@martinbuilt 4 жыл бұрын

Glad you liked it!

@GarySmythe 3 жыл бұрын

Thanks Martin, I've learned so much about my 2004 4.7 HO engine watching your videos! I look forward watching them all. Interesting to know about letting the commercials play out. I'll won't skip them from now on.

@martinbuilt 3 жыл бұрын

You are most welcome Gary and thank you for watching those commercials I do appreciate that, have a great New Year

@bc4092 2 жыл бұрын

Great analysis

@martinbuilt 2 жыл бұрын

Thank you 😊

@toddmoss8672 4 жыл бұрын

awesome job explaining how to remove and putting rockers back on,

@martinbuilt 4 жыл бұрын

Thanks for watching!

@danhambrick6331 4 жыл бұрын

Nice job Martin.The oil bath was priceless.....I wish I would have known about this last Nov. when I changed my head's,I would have used the upgraded rocker arms.

@martinbuilt 4 жыл бұрын

Thanks Dan, I'm glad you it enjoyed it.

@joeyelliott-bh3yb 5 ай бұрын

love watching your videos keep up good work buddy. i have a ram 1500 4.7 very helpful vids

@martinbuilt 5 ай бұрын

Thank you I appreciate that. I'm glad you like them and find them helpful.

@DarkSim77 2 жыл бұрын

Best thing about your videos is how in depth you go..like telling us the correct size socket to rotate the crankshaft..don't have to try 7 different sockets to get the job done..

@martinbuilt 2 жыл бұрын

Thank you I'm glad you liked it and found it helpful.🙂👍

@mikejohnson-rj4uk 3 жыл бұрын

Wow, just found this page and an instant subscribe! My 2000 WJ has 640,000 miles but I'm always looking for 'new' info to keep it going. As a Detroiter. 'lifter,' 'valve adjuster,' whatever, depends on which side of town you're from - Ford, GM or Chrysler. I call them tappets!

@Extinction.of.Innocense 2 жыл бұрын

Since I just found you, I'm not letting go. I already feel as though I owe you money. Great instructor. Funny, I kinda look forward to doing it except doing what I have to do to do it.

@martinbuilt 2 жыл бұрын

I'm glad you liked it and found it helpful.😎👍

@edgreany4226 3 жыл бұрын

I have had a noisy lifter on my 06 Mitsubishi Raider for over a year. One mechanic said "Oh, that's normal". What he didn't tell me was that it may be "a normal failure" on that vehicle but it still needs replacement. THANK YOU for an excellent classroom education. I'll be back. I wish you were in my town.

@martinbuilt 3 жыл бұрын

You are very welcome.

@T3CN01 4 жыл бұрын

15:30 you start to school us on pro mod if your engine is working better you can gain 10 HP love it!

@ricedy6592 2 жыл бұрын

Excellent video. A lot of help!!

@martinbuilt 2 жыл бұрын

Thank you, I'm glad you liked it and found it helpful 👍 😊

@richwilson7017 4 жыл бұрын

Man it was so cool watching that camshaft spin. I’m rebuilding my 2004 4.7 after watching all your videos when I get home I need to see what kind a roller rockers I have. Probably the old style I don’t know that I’ll replace them now but I am putting in new melling lifters. It sounds like have a good lifters is the most important thing. Thanks for putting in the time!

@richwilson7017 4 жыл бұрын

I do have the newer style! I had 315,000 miles and I’m glad I checked them because all the squirted holes were clogged. Will need to clean and I guess start using a senthetic oil more regularly. Thank you!

@martinbuilt 4 жыл бұрын

Thank you, Rich

@wickedpissah6037 3 жыл бұрын

Best video yet

@martinbuilt 3 жыл бұрын

Glad you like it!

@carlcarson9403 Жыл бұрын

That was something else never seen them snap on like that I'm use to the 70 up to I guess late 90 thank you for sharing I'm still scratching my head wow

@AC-gu7rg 3 жыл бұрын

Thanks for the info , greatly appreciated !!

@martinbuilt 3 жыл бұрын

Glad it was helpful!

@rmp608 Жыл бұрын

THANK YOU!!! EXCELLENT VIDEO!!!

@martinbuilt Жыл бұрын

Thank you I'm glad you liked it and found it helpful.😊

@oscarencarnacion5802 Жыл бұрын

You are absolutely a genius

@martinbuilt Жыл бұрын

Thank you. I really appreciate that. I'm glad you liked it and found it helpful.

@sleeperolds 3 жыл бұрын

Awesome video. Thank you!

@martinbuilt 3 жыл бұрын

Glad you liked it

@swatscorner 2 жыл бұрын

Amazing video! You explained it so clearly. Hoping to do this in the 2008 Jeep Liberty 3.7!! Happy wrenching!

@martinbuilt 2 жыл бұрын

Thank you. I really appreciate that. Your 08 Jeep already has the upgraded rocker arms. From 05 and later all 3.7 and 4.7 have the upgraded rockers.

@swatscorner 2 жыл бұрын

@@martinbuilt understood-I knew from your video I had the upgraded rockers. The LASH Adjusters/lifters is what I am thinking need to be replaced (lifter tick). Wonder if with 130k I ought to replace rockers as well.

@martinbuilt 2 жыл бұрын

@@swatscorner I doubt if the rockers need to be replaced. They are pretty much bulletproof.

@swatscorner 2 жыл бұрын

@@martinbuilt good to know! Thanks!!

@edwardhuddleston1548 Жыл бұрын

nice video. Very informative

@martinbuilt Жыл бұрын

I'm glad it was helpful!

@evelioherrera5619 2 жыл бұрын

Great video👌

@martinbuilt 2 жыл бұрын

Thank you, much appreciated 🙏😊

@timothydean 2 жыл бұрын

God bless you finally someone explains it to me . thanks

@martinbuilt 2 жыл бұрын

Thank you I really appreciate that I'm glad you liked it.

@douglasangelflores6796 2 жыл бұрын

Very nice job!

@martinbuilt 2 жыл бұрын

Thank you. Glad you like it.👍🙂

@jakedaniels7546 4 жыл бұрын

Great video, my 04 ram 4.7 with almost 400k miles definitely needs a set of lash adjusters, seemed like a daunting task but it looks like the hardest part is going to be getting the valve covers off...thanks for posting this!

@martinbuilt 4 жыл бұрын

Wow...400K you must be taking great care it, I don't think I would change a thing.

@jakedaniels7546 4 жыл бұрын

@@martinbuilt My pops bought the truck new in 2004, been all over the west coast and all around California for his contracting business. I got it from him about 5 years ago when he got his new GMC - he still misses it every time his Denali is in the shop...lol. Just a testament to regular maintenance and taking care of your vehicle!

@miguel300ish 2 жыл бұрын

Hi I know this is an old video .. but I’m rebuilding the 4.7 in my 2002 ram ... since many parts needed replacement I bought new 2009-2013 cams and I saved some money by buying the upgraded rockers from 2 2012 Jeep’s I found at the junkyard .. they were the 3.7 so I hade to take 2 apart I just gotta say thank you for having this info for you I much appreciate it .. now I’m looking forward to finish my engine and see for myself if all this upgrades add up . I’m also gonna do the injector upgrade .

@martinbuilt 2 жыл бұрын

Just out of curiosity, where did you get the 09 -13 Cam shafts from you have a link to the product? Good luck with the build 👍

@miguel300ish 2 жыл бұрын

@@martinbuilt oh I’m sorry I meant newer cams from the 2009-2013 ... I actually was able to buy them off a dismantler in my town I just checked to make sure the numbers were correct .

@jelqzkolazarov4633 2 жыл бұрын

Respect from Bulgaria 🇧🇬 now I will start project wit my new 4.7 wj but is broken for now ✌

@martinbuilt 2 жыл бұрын

Nice to hear from you 🙂 Good luck with the repairs. Thank you for watching 👀

@tyesquare2624 9 ай бұрын

Always great

@martinbuilt 9 ай бұрын

Thank you

@BuiltByRik 10 ай бұрын

I hear about it but now I seen it thanks Martin I'll use them in my next build. 👍

@martinbuilt 10 ай бұрын

I'm glad you found it helpful thank you for watching.😊

@rufuswimberly7196 2 жыл бұрын

Nice work thanks

@martinbuilt 2 жыл бұрын

I'm glad you liked it. Thank you for watching.🙂

@michaelrowland45 Жыл бұрын

Great Information Martin thanks keep my HO Jeep overland WJ 4.7 going 👍

@martinbuilt Жыл бұрын

Thank you, Glad you liked it and found it helpful.🙂

@michaelrowland45 Жыл бұрын

@@martinbuilt Gday Martin, I was amazed how hard it is to Locate Camshafts for HO . Look forward to chatting again . The information on Jeep WJ is fantastic I watch them regularly. I like air craft hanger heaps of room 👍. Cheers mate

@michaelrowland45 Жыл бұрын

Gday Martin, How are you going Martin? Mate you ever re- grind the camshafts if not available for the HO WJ Jeep 4.7 V8? Or is it not recommended? Regards Mike

@juanmespinoza65 Жыл бұрын

Thank you so much I’m gonna use this upgrade on my 2001 dodge Dakota 4.7. It has a slight lifter sound and gasket leak on the driver side although it is a crate jasper engine about two years old.

@Agronomkleptoman 4 жыл бұрын

thanks for the rocker arm uppgrade notice

@martinbuilt 4 жыл бұрын

Any time!

@yourneck2 4 жыл бұрын

Your the best Mr. Martin, Don’t forget your cam lube people

@martinbuilt 4 жыл бұрын

Thank you, just added them!

@pennypackmtb2542 3 жыл бұрын

I've begun work on my 2000 4.7 WJ. So far every nut and bolt has been rusted solid. So should I call it my Rusty Nut Project, which I have or the Rust Bolt Project. I enjoy your videos very much and I am holding you responsible for encouraging me to rebuild my loved jeep. Truly the best vehicle I ever owned. When my mechanic said Junk it cause it needs new control arms, shocks and an exhausted, I thought time for a lift kit. It just turned over 100,000 miles. So, I have begun.

@martinbuilt 3 жыл бұрын

Wow only 100k that's nothing, to bad about the rust

@itsmeagain8518 Жыл бұрын

I have a 2005 Liberty Sport 3.7. From the list of affiliates you provide I am not sure which rocker arms and lifters will fit my 3.7. And, again, excellent video. I taught auto body repair for over 25 years. You would make a good instructor. Thanks, Jim

@martinbuilt Жыл бұрын

Thank you Jim I really appreciate that here's a couple links below that should help you out. Lifters amzn.to/3zjtAZb Rocker arms amzn.to/3PrS4VU

@LHTAS 2 жыл бұрын

Siempre veo los PATROSINADORES. GRACIAS compartire tus videos en mi pagina.

@martinbuilt 2 жыл бұрын

Thank you, I appreciate that, glad you liked it.

@mlubnani 4 жыл бұрын

Great video!!! One question, I changed the Cloyes timing kit and I feel the same tensioner knock noise I had before. Disappears within 2 to 5 minutes of turning on. the oil pressure measured it and it is at 70 cold and at 18 hot idle. I put liqui moly for botadores and I do not improve. What can be?

@IanMcDonald-ro5xm Жыл бұрын

Jeep Chrystler, AND JEEP!? Thanks to you Martin and this video I was able to do this project on my jeep. I used a tool for interior / trim clips to get them out that happened to be 10mm. It gets real hairy on the back passenger side but it can be done! I used the new rockers from the 2005 like you said and I also confirm THEY DO FIT!!!! Thanks for putting this together. All of my youtube advice will come from you from now on! (And scotty kilmer lol)

@IanMcDonald-ro5xm Жыл бұрын

PS I popped the rockers in with my tire iron LOL

@IanMcDonald-ro5xm Жыл бұрын

Also to anyone else reading this, probably the rocker kicked off due to poor oil delivery. My suggestion is to replace the worn lifter but also pop off the oil pan and clean the suction filter.

@mercedesmariasilvadeperez3042 4 жыл бұрын

Buenas .excelente explicación y a su vez la mejora para que no salpique .gracias .Saludos desde Venezuela

@martinbuilt 4 жыл бұрын

Translated comment: Good. Excellent explanation and in turn the improvement so that it does not splash. Thank you. Greetings from Venezuela Thank you, stay safe.

@hobbyprison 3 ай бұрын

Hey Martin. Thanks for the video. You have a lot of really good info. Was wondering if I put 08 cams in my 04 4.7 HO if I’ll need to replace the valve springs.

@hardworkingandunderpaid3635 3 жыл бұрын

Thanks for the info it helps...

@martinbuilt 3 жыл бұрын

No problem, thank for watching!

@Rockr69747 4 жыл бұрын

Thanks Martin. My wallet is thinking you're not a nice man, but your content is golden. I'll tell the wallet to quit thinking. Keep that content coming!

@alexkoynov 20 күн бұрын

Спасибо, Мартин! Очень полезное видео. 👍

@martinbuilt 20 күн бұрын

I'm glad you liked it and found it helpful thank you for watching.

@agreene638 5 ай бұрын

Thanks for mentioning what year they were redesigned and what was changed

@chrisbeitzel4788 4 жыл бұрын

Awesome information. Love the bloopers, That's my favorite part! I hope your looking into the roller timing chain set-up?? Stay safe out there..

@xc8487 4 жыл бұрын

What roller timing chain?

@martinbuilt 4 жыл бұрын

Chris took a late model 4.7 timing chain (that is a single roller) and modified to fit the older 4.7's

@martinbuilt 4 жыл бұрын

I did remove the cam timing wheel from one of the older cam gears but, that is as far as I got.

@martinbuilt 4 жыл бұрын

Hi Chris, where did you get the chainset you used and what hardware will I need from the newer engine to complete the conversion?

@chrisbeitzel4788 4 жыл бұрын

Okay, Rockauto has a Cloyes set #90393SF listed under 2008 dodge Dakota 4.7 for $270.00. This will have everything you will need, except the toner wheel from a 2002 4.7. Grind the rivets from the back side and punch then out enough the remove the toner wheel, Swap the 02 onto the 08 sprocket and weld up the rivets. I spoke with Cloyes about what I was doing and he agreed it would work. And mine is working great. Cloyes has a video on youtube with both applications if you need to watch and see what they did differently. Best of luck.

@dwightstebner2345 5 ай бұрын

Very nice video! I sense a lot of knowledge from Martinbuilt. I see headers installed, curious as to what other performance parts are available for the 3.7? 350000 km on my Liberty, glad I found this video

@alwayspackin1 Жыл бұрын

You are awesome thanks

@martinbuilt Жыл бұрын

Thank you I'm glad you liked it and found it helpful.

@davekana8388 2 жыл бұрын

Liked and subscribed, just brought home a 2004 Rengade, 150K, hope I don’t need but great info, thanks!

@martinbuilt 2 жыл бұрын

Awesome 👌 congratulations. Thank you for subscribing and watching 👀

@davekana8388 2 жыл бұрын

@@martinbuilt ☕️💪

@gpsbando Жыл бұрын

Man I Love You,you Just literally put $600 In My Savings I've completed the job client satisfied 😊❤

@martinbuilt 5 ай бұрын

I'm glad I could help and thank you for watching.😎🤑

@Peter-od7op Жыл бұрын

Ty i have 4.7 in dodge pick up other day barley got to my friends shop. No 2 cylinder missing like crazy violent really. I bet lifter failed. Hope rocker did not cause to much damage to engine. I subscribed

@Kolonol1 4 жыл бұрын

Always always turn the motor kn the direction of running rotation... Love those shiny Valve covers...I'm still working on mine...Amazon screwed up my orders

@Kolonol1 4 жыл бұрын

I didnt know you get commission through Amazon...you got double from me because I had to order those Dremel polishing wheels twice XD

@martinbuilt 4 жыл бұрын

Thank you, I appreciate that, Yes as long as you go through the amazon link in the description the channel receives a commission.

@claudio_sergiacomo 3 жыл бұрын

What an amazing tutorial about the rockers and lifters... Really really helpful. I will do my lifters myself on my Jeep 3.7 2006 cause they make sometimes noise for a coupe of seconds at startup. I wonder where can I get those chrome shinny valve covers for my 3.7 ??

@martinbuilt 3 жыл бұрын

You may want to try some Marvel Mystery oil that could cure your lifter noise. On your next oil change use half a quart. Then if that doesn't fix it then I would replace the lifters. If you want your valve covers to look like those look up how to Polish magnesium.

@leograjalts Жыл бұрын

Good evening, excellent video and explanation, I just wanted to ask you, I have a 3.7 jeep liberty, can I put a 4.7 rock arm and lifter on it without problems?

@thomasvaninwagen2256 2 жыл бұрын

I have a 01 Dodge Dakota it dropped #8 rocker and I don't have compression so It probably dropped the valve. I haven't looked down the plug hole to see how bad. Than you for the video.

@martinbuilt 2 жыл бұрын

I bet you dropped a valve seat and the valve is hung open and that's why the rocker came off unfortunately you probably gonna have to replace the cylinder head or a machine shop should be able to repair the head.

@bradleycrenshaw6778 2 жыл бұрын

Mr. Martin thank you so much for what you do and sharing your vast knowledge about the 4.7. Because of you I am no longer scared to do these modifications to my vehicle. I am currently in the middle of a 4.7 to 4.7 swap for my 04 ram 1500 4.7 SLT 4X4 because of a blown head gasket and milky oil. I bought another donor 04 ram 1500 4x4 because it currently has a strong 4.7 with no issues. I do have a question if you have time. Both trucks have the 8th digit N in the VIN. The donor is an automatic tranny while the recipient is a 5spd. Watching your video on replacing the stock cams with the earlier HO cams you scared the daylights out of me. You made mention about the PCM plugs. The donor (automatic tranny) has a 4 plug PCM while my truck has a 3 plug PCM. Is this due to the difference in the auto vs 5spd or am i going to run into the tone ring issue? Also my new to me cams are marked 1414AB and 1413C. Did I do good on the pick and will they work? Again thank you so much for your time and devotion to this channel. Sending you some educational funding as soon as i post this !!

@martinbuilt 2 жыл бұрын

Thank you Bradley for the kind words and generous donation I really appreciate that. Yes the camshafts you got the 1414 and the 1413 are HO Cam shafts. Now the situation with the number of plugs on the ECM on your donor 04 seems a bit odd that it only has 3 and this could be because of the manual transmission the 4th plug is for automatic transmission control. To verify that both of them have the same tone ring on the crank shaft or reluctor gear I would verify that they have the same camshaft gear on the passenger side compare the rectangle holes and if they are in the same location then you are good to go. I would remove the Cam gear from the engine that has the blown head gasket lay that Cam gear up against the donor vehicle engine and compare carefully to verify that they are the same or not. Let me know what you find you can always contact me on my Facebook Messenger there is a link in the description of all my videos.

@KingJamesV-jo7nv 4 ай бұрын

Thanks for your video. After doing the rocker arms and lifters on the passenger side, my check engine light came back on and I can’t get engine to rev above 2200 rpm. Could it be related to hand turning the crankshaft ?

@nikozoumis9506 4 жыл бұрын

Thank you

@martinbuilt 4 жыл бұрын

You're welcome

@douggavic5682 3 жыл бұрын

Hey Martin! Love all your 4.7 videos! You have no idea how much I have learned from your videos!! Thank you. Wondering what rocker arm brand you put in with the new design? Huge price difference and origin of manufacture. My rockers seem all right, but have old style you mention in video (2001 dodge dakota 4.7). Swapping all lifters and seems like good time to change to new style. Received DNJ (made in china). Got the similar priced EngineTech rockers you mentioned above coming this week. I am torn if I should just leave the old ones or not. Just don't want to put in low quality arms, but think the new design makes sense. Also everything says the Melling MR-1345 rocker doesn't fit 2001 but fits 2002, do you think that is a screw up or is there something to it.

@martinbuilt 3 жыл бұрын

Thank you, I really appreciate that. I like the OEM rockers and I just get them from the local Pick-a-Part and them just clean them up with some Totally Awesome and reoil before installing them. The Melling MR-1345 will fit all 99-13 3.7 and 4.7 engines.

@stephendunne8537 4 жыл бұрын

Hi Martin, thanks for high quality video, question can I put new valve stem seals on without removing camshaft, and just remove rocker arms. Thanks a million!

@martinbuilt 4 жыл бұрын

Yes you can, They do make a special tool to compress the spring. You will also need to use compressed air to the cylinder to keep the valve from falling into the cylinder.

@raynaldturner9679 2 жыл бұрын

thanks

@corneliusbilljohn9465 4 жыл бұрын

Man you made dat easy nice video

@martinbuilt 4 жыл бұрын

Glad you liked it

@corneliusbilljohn9465 4 жыл бұрын

@@martinbuilt I dnt have to set da timing or anything like dat

@corneliusbilljohn9465 4 жыл бұрын

Hey bud i got a 2004 malibu 2.2 reset my timing and still no start wat u think is wrong wit it eco pack or wat

@ariele4278 9 ай бұрын

Hello, thanks for the video, very informative, Can you apply this method on 3.6 pentestar

@martinbuilt 9 ай бұрын

Thank you. I appreciate that I'm glad you like it. Unfortunately, the 3.6 is not as easy as the 4.7 or the 3.7.

@gilliland426 2 жыл бұрын

the driver side valve cover is a very tight fit on a dakota pickup.

@martinbuilt 2 жыл бұрын

Yes, it is. On the 00-04 Jeep Grand Cherokee it's the passenger side that's really tight. The battery, battery tray, A/C compressor, and more need to be removed.

@charliedee9276 4 жыл бұрын

Would you use these if you already have solid lash adjusters? I would think they are not needed in that case.

@Artlopez105 2 жыл бұрын

Martin please tell us what do you think about the rocker locks

@invisabledad 3 ай бұрын

Still not sure what to get. Your links no longer work. There are several rocker links. Can you update them please?

@Toolaholic7 2 жыл бұрын

Will nick the cam doing that.A special tool is needed.Another cause of the rocker arms coming out is a dropped valve seat,have seen this before

@copenhagin1 3 жыл бұрын

Hello Martin I clicked the link for the B-2271 lifters and they are out of stock do you know anywhere else I can get these lifters I've been and will continue to keep looking, you have been very helpful and I greatly appreciate it and the time you take to explain to in your videos

@charliedee9276 3 жыл бұрын

They changed the lash adjuster in 05 or 06 as well. The 2271 adjuster is part 53021077 and the new one is part 53021894AA or Sealed Power HT-2308.

@TransformationwiththeWordofGod 2 жыл бұрын

Where do I get the upgraded rocker arms and valves for my 2003 Dodge ram 1500 4.7

@P.A.C.E.automotive 3 жыл бұрын

Awesome instructional Martin! Do you ever see the roller of the rocker go bad? If someone already has an 05-07 would replacing the rocker arms as maintenance with the lash adjusters make sense?

@martinbuilt 3 жыл бұрын

Thank you, I personally have never seen one go bad, I wouldn't replace them.

@OscarHernandez-ym4hx Ай бұрын

I am getting too much negative camber on my right front wheel. Any videos on tigjtening up front of vehicle.

@Elvenudo1986 2 жыл бұрын

Hello, thank you for the video and all the info and also where can I buy those rockers and lifters?

@martinbuilt 2 жыл бұрын

Here's a link for the rocker arms. amzn.to/3L1ymgs

@connorsmith4234 3 ай бұрын

ive got a 3.7 im gonna rebuild, i pulled it because it wouldnt idle,blown head gaskets, and higher miles, and i droped 4 and 6 exhaust rockers what woulda caused that??

@juanmata5292 3 жыл бұрын

Thanks

@martinbuilt 3 жыл бұрын

No problem

@greghubert4968 4 жыл бұрын

The way you explaining and showing is amazing . You love your shiny valve covers:) I just ordered ones from scrap yard,will do the same project,thank you Martin

@martinbuilt 4 жыл бұрын

Glad you like them!

@misadventureswiththemartys312 3 жыл бұрын

Hey Martin Love this video. When upgrading the rocker arms can the extra pressure do damage?

@martinbuilt 3 жыл бұрын

Thank you, no there be no damage only benefits.

@jln1122 3 ай бұрын

I just rotate the motor and cam so the lobes are in a neutral position and take the bolts out of the cam caps and carefully lift the cam without affecting the timing to remove and install the rockers. Way easier that way

@xAnAngelOfDeathx 10 ай бұрын

Liked and subbed, great video.

@martinbuilt 10 ай бұрын

Thank you I really appreciate that i'm glad you liked it and found it helpful.

@Cuidadopisado 2 жыл бұрын

Good stuff Martin. I am in the market for a 2002 liberty and was researching some set backs I might come across. You addressed a major concern I’ve read about the 3.7 and 4.7 engines. I do have a question, are these parts you listed interchangeable between both engines?

@martinbuilt 2 жыл бұрын

Thank you. I'm glad you're enjoying the content.. Yes, the rocker arms and lash adjusters are interchangeable between the 3.7 and 4.7

@albertogonzalez5564 4 жыл бұрын

Awesome video. Is there a difference from the lifters you have listed to the ones from airram?

@martinbuilt 4 жыл бұрын

Thank you, no these are the same lifters, I purchased them from airram.

@grahammay4727 Жыл бұрын

I know this is at least 3 years ago. The links (20.05.23) are all out of stock for the new type of rockers as well. I was just wondering if you have used the rocker locks that are made for the 3.7 & 4.7L as well and if you think they would be of value and last the distance?